Puig Rim Strips Installation Manual for BMW R1200GS ADV. (2014-2018) and R1250GS ADV. (2018-2020)

Zavedení

This manual provides detailed instructions for the proper installation and care of your Puig Rim Strips. These rim strips are designed to enhance the aesthetic appeal of your BMW R1200GS Adventure (2014-2018) or R1250GS Adventure (2018-2020) motorcycle wheels. Please read all instructions carefully before beginning the installation process to ensure a successful application and long-lasting results.

Bezpečnostní informace

Always prioritize safety when working on your motorcycle.

• Před zahájením jakékoli práce se ujistěte, že je motocykl stabilní a bezpečně podepřený.
• Work in a well-lit and clean environment.
• Keep all tools and materials organized to prevent accidents.
• If you are unsure about any step, consult a professional motorcycle mechanic.
• Uchovávejte výrobek mimo dosah dětí.

Co je v krabici

Your Puig Rim Strips package should contain the following components:

• Puig Rim Strips (sufficient quantity for both wheels)
• Application instructions (this manual)

Note: Additional tools required for installation (not included) are listed in the "Preparation" section.

Instalace

1. Příprava

Proper preparation is crucial for successful adhesion and a clean finish.

1. Vyčistěte kola: Thoroughly clean the rim surface where the strips will be applied. Use a degreaser or isopropyl alcohol to remove all dirt, grease, wax, and any other contaminants. Ensure the surface is completely dry before proceeding.
2. Sbírejte nástroje: You will need a clean cloth, a spray bottle with water (optional, for wet application), and a squeegee or soft card (e.g., credit card) for smoothing.
3. Pracovní prostředí: Perform the installation in a dust-free environment with a temperature between 15°C and 25°C (59°F and 77°F).

2. Kroky aplikace

Follow these steps carefully for optimal results. It is recommended to apply the strips one section at a time.

1. Umístění: Carefully peel a small section of the backing paper from one end of a rim strip. Align the strip with the desired position on the rim.
2. Initial Adhesion: Press the initial section firmly onto the rim.
3. Postupná aplikace: Slowly peel off more of the backing paper while simultaneously pressing the strip onto the rim. Use your thumb or a squeegee to smooth out the strip, working from the center outwards to avoid air bubbles.
4. Odstraňte vzduchové bubliny: If air bubbles appear, gently lift the strip back to the bubble and reapply, smoothing it down. For stubborn bubbles, a small pin can be used to prick the bubble, then press the air out.
5. Repeat for all sections: Continue this process around the entire rim until all strips are applied. Ensure there are no overlaps or gaps between sections.
6. Final Press: Once all strips are in place, firmly press along the entire length of each strip to ensure maximum adhesion. Pay special attention to the edges.

Obrázek 1: Příkladample of Puig Rim Strips correctly applied to a motorcycle wheel. Note the clean alignment and smooth finish.

Obrázek 2: Detailní view of the Puig Rim Strips on a motorcycle wheel, demonstrating the product's appearance after installation.

Péče po instalaci

After installation, allow the adhesive to cure properly before exposing the motorcycle to harsh conditions or washing.

• Doba vytvrzování: Avoid washing the wheels or exposing them to heavy rain for at least 24-48 hours after application to allow the adhesive to fully bond.
• Počáteční kontrola: Periodically check the rim strips for any signs of lifting or damage, especially after the first few rides.

Údržba a čištění

To maintain the appearance and longevity of your Puig Rim Strips, follow these cleaning guidelines:

• Jemné čištění: Clean the rim strips with mild soap and water using a soft cloth or sponge.
• Vyhněte se agresivním chemikáliím: Do not use abrasive cleaners, solvents, or high-pressure washers directly on the rim strips, as this can damage the material or adhesive.
• Sušení: Pat dry with a clean, soft cloth to prevent water spots.

Odstraňování problémů

Here are solutions to common issues encountered during or after application:

• Vzduchové bubliny: If small air bubbles are present after application, they may dissipate over a few days, especially in warm weather. For larger or persistent bubbles, gently prick them with a fine needle and smooth the area with your finger or a squeegee.
• Edges Lifting: If edges begin to lift, ensure the surface was thoroughly cleaned and dry before application. Re-press the lifting edge firmly. If the issue persists, the strip may need to be replaced.
• Špatná přilnavost: This is usually due to inadequate surface preparation (e.g., grease, dirt, or moisture). Ensure the rim is perfectly clean and dry before applying.

Specifikace

Informace o záruce

For detailed warranty information regarding your Puig Rim Strips, please refer to the official Puig webstránky nebo se obraťte přímo na jejich zákaznický servis. Záruční podmínky se mohou lišit.

Zákaznická podpora

If you have any questions, require assistance with installation, or need to report a product issue, please contact Puig customer support through their official webmístě nebo autorizovaným distributorům.