Návod k obsluze zadního tlumiče Puig 6447J Matt Black

1. Úvod

This instruction manual provides essential information for the proper installation, operation, and maintenance of your Puig 6447J Matt Black Rear Hugger. Please read this manual thoroughly before beginning installation to ensure correct procedure and safe use.

The Puig 6447J Rear Hugger is designed for supersport motorcycle models. It features an aluminum support and is constructed from durable materials to provide protection for the rear suspension, under-tail area, and rider from road debris and spray.

2. Bezpečnostní informace

• Během instalace vždy používejte vhodné osobní ochranné prostředky (OOP).
• Před zahájením jakékoli práce se ujistěte, že je motocykl stabilní a bezpečně podepřený.
• Pokud si nejste jisti některým krokem instalace, poraďte se s kvalifikovaným motocyklovým mechanikem.
• Neupravujte výrobek ani jej nepoužívejte k jiným účelům, než ke kterým je určen.
• After installation, verify that all fasteners are tightened to the manufacturer's specifications and that the hugger does not interfere with any moving parts of the motorcycle.

3. Obsah balení

Před zahájením instalace ověřte, zda jsou všechny komponenty přítomny:

• 1 x Puig 6447J Matt Black Rear Hugger
• Mounting hardware (bolts, washers, spacers, brackets as required for your specific motorcycle model)
• Pokyny k instalaci (tato příručka)

4. Nastavení a instalace

The installation process may vary slightly depending on your specific motorcycle model. Refer to your motorcycle's service manual for specific torque values and component removal procedures. The following steps provide a general guide:

1. Příprava motocyklu: Park the motorcycle on a level surface and secure it on a paddock stand or center stand to lift the rear wheel off the ground. Allow the exhaust system to cool completely if it is near the installation area.
2. Access the Installation Area: Depending on your motorcycle, it may be necessary to remove the rear wheel, chain guard, or other components to gain clear access to the swingarm and suspension area where the hugger will be mounted.
3. Position the Hugger: Carefully position the Puig Rear Hugger against the swingarm or existing mounting points. Identify the attachment points for the supplied brackets and hardware.
4. Připevněte montážní konzoly: Secure any necessary mounting brackets to the swingarm or other designated points using the provided hardware. Do not fully tighten bolts at this stage.
5. Mount the Hugger: Attach the rear hugger to the brackets or directly to the motorcycle's frame/swingarm using the remaining hardware. Ensure proper alignment and clearance with the tire, chain, and suspension components.
6. Utáhněte všechny upevňovací prvky: Once the hugger is correctly positioned and aligned, progressively tighten all bolts and nuts. Refer to your motorcycle's service manual for recommended torque specifications for relevant fasteners.
7. Znovu sestavte komponenty: Reinstall any components that were removed (e.g., rear wheel, chain guard).
8. Závěrečná kontrola: Before riding, manually rotate the rear wheel to check for any interference between the hugger and the tire, chain, or suspension. Ensure all fasteners are secure.

Obrázek 1: The Puig 6447J Matt Black Rear Hugger. This image shows the component designed to protect the motorcycle's rear suspension and under-tail area from road debris.

5. Návod k obsluze

Once installed, the Puig Rear Hugger operates passively by deflecting water, dirt, and debris away from the rear shock absorber, under-tail components, and the rider's back. No active operation is required.

6. Údržba

• Pravidelný úklid: Clean the rear hugger regularly with mild soap and water to remove accumulated dirt and grime. Avoid abrasive cleaners or solvents that could damage the finish.
• Inspekce: Periodically inspect the hugger for any signs of damage, cracks, or loose fasteners. Check that it maintains adequate clearance from the tire and other moving parts.
• Kontrola upevňovacích prvků: Over time, vibrations can cause fasteners to loosen. Check all mounting bolts and nuts periodically and retighten them to the recommended torque specifications if necessary.

7. Řešení problémů

• Hugger is Loose: Check all mounting bolts and nuts. Ensure they are tightened securely. If the issue persists, inspect brackets for damage or improper installation.
• Interference with Tire/Chain: Immediately stop riding if you notice any rubbing. Re-check the installation and alignment. Ensure the hugger is correctly positioned and that all spacers (if applicable) are used as intended.
• Neobvyklé zvuky: Investigate any new noises coming from the rear wheel area. This could indicate loose components or interference.

8. Specifikace

9. Záruka a podpora

Informace týkající se záruky na produkt, vrácení zboží nebo technické podpory získáte od oficiálního prodejce Puig. website or contact your authorized Puig dealer. Keep your proof of purchase for any warranty claims.