Lineární LED světlo Technilight GEN II

Specifikace produktu

Žádný.	Velikost	A (v)	B (v)	C (in)	D (v)	E (in)
1	2 FT	3.346	18.858	3.346	/	/
2	4 FT	3.346	42.480	3.346	/	/
3	6 FT	3.346	66.102	3.346	/	/
4	8 FT	3.346	43.189	3.346	43.189	3.346

Návod k použití produktu

Montážní pokyny:
The suspension mount should be securely fixed to the aircraft using the provided screw nut and thread locker. Ensure the waterproof connector is passed through the gasket and canopy and fixed with a screw nut.

Pokyny pro elektrické zapojení:
Pass the AC wire into the waterproof connector and secure it with a screw cap. Connect the L pole to the black wire, N pole to the white wire, GND to the green wire, DIM+ pole to the purple wire, and DIM- pole to the pink wire.

Pokyny pro propojitelné příslušenství:
In order to link fixtures, make sure that the quantity meets the specified conditions based on input voltage a wattage per fixture, as mentioned in the manual.

DŮLEŽITÉ BEZPEČNOSTNÍ POKYNY

Read this installation guide prior to attempting installation. Always turn OFF the main power before starting your installation. Consult a qualified electrician before installation. Installation should be carried out by a qualified electrician.

1. During installation, basic safe precautions ou always be followed, including the following listed. Do not install the lighting system in a wet location. Ensure the appropriate connectors match the luminaire fixture.
2. Neinstalujte žádnou část svítidla níže než 5 stop nad podlahou.
3. Do not install any luminaire assembly closer than 5 inches from any window treatments,i.e., curtains, blinds, or any similar combustible type material.
4. Nepokoušejte se napájet nic jiného než svítidla.
5. To reduce the risk of fire and electric shock, do not attempt to connect power tools, extension cords, appliances, or the like to the track. Maintenance of the luminaires should be performed by a person (s) familiar with the luminaire’s construction and any hazards involved. Regular fixture maintenance programs are recommended.
6. Nepřekračujte jmenovitý objem napájenítage nebo amperage hodnocení.
7. Před prováděním jakékoli instalace nebo údržby vypněte napájení pojistkové nebo jističové skříňky.
8. Noste boty s gumovou podrážkou a pracujte na pevném dřevěném nebo nevodivém žebříku.
9. The lighting product must be mounted in locations and at heights in compliance with the National.
10. Electrical Code and local building codes.
11. Installing contrary instructions may cause unsafe conditions.
12. To avoid hazards to children, take accountability for all parts and dispose of all packing materials properly.
13. It may be necessary to clean the refractor/lens.
    The frequency of cleaning will depend on the ambient dirt level and minimum light output, which is acceptable to the user. The refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water, and wiped dry. Should the optical assembly become dirty on the inside, wipe the aspheric lens and clean it in the above manner, replacing damaged gaskets as necessary.
14. Call the Technical Support department for any installation questions.
15. Do not install a damaged product. This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
16. These instructions do not purport to cover all details or variations in equipment nor provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or particular problems arise, not covered sufficiently for the purchaser’s or owner’s purposes, please contact the Technical Team.

POZOR
This equipment is intended to be installed only by qualified personnel. The installation must be made by the current edition of the National Electrical Code (NEC) and all applicable state and local building codes. The final installation must be approved by the appropriate, qualified electrical / building inspector(s). Improper installation may result in a fire or an electrical hazard.
Ensure the electrical power to the circuit has been disconnected before installing the electrical system.

VAROVÁNÍ

• Risk of fire. Most dwellings built before 1985 have supply wires rated at 600 °.C
• Před instalací se poraďte s kvalifikovaným elektrikářem.
• Properly ground the electrical enclosure.
• Abyste předešli poškození nebo otěru kabeláže, nevystavujte kabeláž hranám plechu nebo jiným ostrým předmětům.
• Use only UL-approved wire input/output connections.
• Minimum size 18 AWG or 14 AWGG if there are any continuous runs.
• If the fixtures are connected in a continuous run, do not exceed the allowable number of fixtures in series/power in continuous runs.
• Inrush currents must be taken into account by the electrician to ensure proper circuit design.

NÁSTROJ

Aircraft Suspension Mount

Instalační sady

Žádný.	Velikost	A(in)	Zásobník)
1	2 FT	22.205	/
2	4 FT	45.827	/
3	6 FT	69.449	/
4	8 FT	46.535	46.535

1. Drill a hole of 5.0mm in diameter at the location required for installation. Then, install the plastic anchor into the hole with a hammer.
2. lnsertrt PA4*30 Screws into the screw holder and then drill into the plastic anchor.
3. Zajistěte podstavec z ocelového lana ke koncovým deskám pomocí šroubů PM4*8.
4. Press down the inner hole of the steel wire rope pedestal, and let the steel wire rope go through the hole.
5. Connect and DIM- of the AC input wire to the DIM- of the C terminal.
6. Press the pedal of the steel wire rope pedestal to adjust the steel wire rope, and then finish the installation.

Instalace zavěšení vrchlíku

1. V místě požadovaném pro instalaci vyvrtejte otvor o průměru 5.0 mm, jak je znázorněno na obrázku. Poté zatlučte plastovou kotvu do otvoru.
2.  Insert PA4*30 screws into the M-type mounting bracket and then drill into the plastic anchor.
3. Zajistěte podstavec z ocelového lana ke koncovým deskám pomocí šroubů PM4*8.
4. Press down the inner hole of the steel wire rope pedestal, and let the steel wire rope go through the hole.
5. The thread locker passes through the canopy and is fixed with a screw nut, and the waterproof connector passes through the gasket and the canopy and is fixed with a screw nut
6. Press the steel wire rope holder as shown in the figure, and then insert the stainless steel wire into the inner hole of the steel wire rope holder. The mounting height of the lamp lze nastavit tímto držákem ocelového lana.
7. Pass the AC into the waterproof connector, fix the AC wire with a screw cap, connect the L pole to the black wire, the N pole to the white wire, the GND to the green wire, the DIM+ pole to the purple wire, and the DIM- pole to the pink wire
8. Upravte délku vstupního kabelu AC, zarovnejte boční otvor krytu a montážní konzolu M, jak je znázorněno na obrázku, a poté utáhněte šroub.
9. Instalace je dokončena.

Propojitelná instrukce

Poznámka: Dostupné pouze pro propojitelné produkty.

1. Measure the ceiling, mark the position for the first Linear Light to the ceiling as instructed in a Rope Suspension Installation.
   

   A                  B               C                D
   Žádný.	Velikost	A(in)	Zásobník)	C(in)	Rámus)	Poznámka
   1	2 FT	22.920	23.630	22.920	/	3ks propojitelný schematický výkres
   2	4 FT	46.540	47.250	46.540	/	3ks propojitelný schematický výkres
   3	6 FT	70.160	70.870	70.160	/	3ks propojitelný schematický výkres
   4	8 FT	46.540	47.250	47.250	46.540	2ks propojitelný schematický výkres

2. Install Linear 1, then connect the AC line; remove one end cap as shown on (2-a-b)Insert the linkable bracket into the Linear, connect with the buckle inside the Linear, and then take out the inside linkable wire. ( Five colors)
3. Insert the Linear Light as Step 2 and adjust the steel wire rope to the same height., Then, move out the two end caps of Linear2.lift up the up light, and disconnect the AC wire. Keep the female plug on the side ends
4. Connect the male plug of Linear I and the female plug of Linear 2, and insert the bracket the Linear 2, making them seamless and linkable together.
5. Check the status after linking, and make sure no gap between the two lines.
6. Make sure the male and female plugs have been connected well, and press $ on the uplight module. Put it back to the top of Linear1 and Linear2
7. Install the Linear Light 3,4,5,6, and 7 as in the above method, and keep one main input cord on one side for wiring rounding. Adjust the steel wire rope to the same height. Then finish the installation.

POZNÁMKA:
LED LINEAR CAN BE GAPLESS LINKED TOGETHER AS NEEDED,
( if you order to use 18# cord, More Links can be customized.)

Wall Mount (Type-C)

Instalační sady

1	C Držák pro montáž na stěnu	1 PC
2	Čtvercové dekorativní	1 PC
3	L podpora	2KS
4	Plastová kotva	4KS
5	Crosshead tapping	4KS
6	Ruční šroub	4KS
7	Šroub	1 PC
8	Koncový uzávěr	2KS
9	Linkable bracket	1 PC

1. Drill a Hole in the wall based on the Length of the Fixture, fix the plastic anchor in the hole, and fix the mount bracket on the Wall.
2. Push the L support bracket into the wall mount bracket as follows.
3.  Connect L, N, GND, DIM+, and DIM-0fAC input wire to L, N, GND, DIM, and DIM- of the AC output wire
4. Get the linear light installed into the wall mount bracket as shown picture. Using the hand screw to secure the linear light.
5.  The linkable bracket is inserted into one fixture and connects the male and female connectors, and the other part of the linkable bracket is inserted into the other fixture. Then the fixture is fixed on the wall-mounted kit.
6. Install the end caps, the connector wire must get through the correct place on the end caps as shown in the picture.
7. Rozsvítit světlo.

Povrchová montáž

Instalační sady

1. Drill a Hole in the ceiling based on the length of the fixture, and fix the plastic anchor in the hole.
2. Upevněte držák pro povrchovou montáž na strop pomocí šroubu PA4*30.
3. Zavěste bezpečnostní lanko přípravku do drážky držáku pro povrchovou montáž.
4. Wiring the fixture with the supply power, clear up the wires and safety cables, and clip the fixture into the slot of the surface mount plate on both sides
5. Fix screws on two sides of the fixture
6. Rozsvítit světlo.

T-grid Recessed Mount with Fringe

Frame Recessed Mount with Clips

E-Series

Change PC Lens with Parabolic Lens

Link Pattern

1. Pattern Suspend Mount as a Separate Part.
2. Pattern Suspended Mount as Link Part.

Linkable fixtures Qty need to meet the following two conditions:

1. N≤7pcs
2. Vstupní objemtage = 120V , N*P≤420W Input voltage = 277V , N*P≤960W Input voltage = 347V, N*P≤1200W

Poznámka: N = Qty of linkable fixtures, P = Wattage na zařízení

Toto schéma zapojení vyžaduje více než dva body zapojení AC vstupu.

Často kladené otázky

• Otázka: Kolik bodů zapojení je potřeba pro schéma spojování?
  A: The splicing diagram requires more than two AC inlet wiring points for proper installation.
• Otázka: Jak by měly být svítidla propojena?
  A: To link fixtures together, ensure that the quantity meets the conditions specified in the manual based on input voltage a wattage na zařízení.

Dokumenty / zdroje

Lineární LED světlo Technilight GEN II [pdf] Instalační průvodce 014-0004-0013 A5, 014-0004-0013 A5, 014-0004-0013 A5, Lineární LED světlo GEN II, Lineární LED světlo, Lineární světlo, Světlo

Reference

• Uživatelská příručka