RTX 8930 Wireless Dect Headset
NADVIEW
This manual explains how to operate the RTX SME VoIP DECT Headset (RTX8930) in generic mode, including power on/off, registration, basic call handling, volume control, and microphone muting.
Specifikace
- Model: RTX8930 headset
- Ovládání hlasitosti: Six volume steps (beeps indicate adjustments and limits)
- LED behavior (power/registration status): Blue LED blinks fast during initial signal detection/registration mode; after subscription it blinks with a 2-second interval
- Power-off key combination: Long-press AUX + VOL+ + VOL- for five seconds
Quick Setup & Use
- Zapnout: Stiskněte tlačítko AUX key. Wait for the blue LED to blink fast until a signal is detected; once subscribed, the voice prompt “Headset subscribed” plays and the blue LED changes to a 2-second interval.
- Initial registration: For first-time setup, switch the headset on; it enters registration mode automatically (blue LED blinking fast).
- Subsequent (re-)registration: Stiskněte a podržte HOOK OFF spolu s VOL+ a VOL- until the blue LED starts blinking fast. (Note: the blue LED will not enter registration mode if the unit is cradled and charging.)
- Přijmout hovor: Stiskněte HOOK OFF.
- Ukončení hovoru: Stiskněte HOOK OFF znovu.
- Adjust volume during a call: Stiskněte VOL+ zvýšit a VOL- snížit.
- Ztlumit/zapnout mikrofon: Stiskněte ZTLUMIT to toggle mute on and off.Headset Operations Manual
O tomto dokumentu
This document describes the features and functionalities available in the RTX SME VoIP DECT Headset. We describe how to operate the headset without going into details about its mechanical features. The reference for features and operation in this manual is RTX generic mode.
PublikumTato příručka je určena pro běžné uživatele i systémové administrátory.
ZkratkyPro účely tohoto dokumentu platí následující zkratky:
- DECT: Digitální vylepšené bezdrátové telekomunikace
- IPEI: Mezinárodní identita přenosného zařízení
- MAC: Řízení přístupu k médiím
- TELEFONNÍ ÚSTŘEDNA: Soukromá pobočková burza
Reference/Související dokumentace
- [1]: How_To_Deploy_SME_Network_V1.3
- [2]: SME VoIP System Guide, Version 2.5
Historie dokumentu
| Revize | Autor | Datum vydání | Komentáře |
|---|---|---|---|
| 0.1 | TMS | 26. července 2016 | Počáteční verze. |
Ochranná známka
| Jméno zákazníka | RTX | Wildix | SNOM | Strongbyte |
|---|---|---|---|---|
| Model č. | RTX8930headset | WAIR-Headset | A190 | VCV2840 headset |
| HVIN | 8930V10 | WAIRV10 | 190V10 | 2840V10 |
| Ochranná známka |
Základní operace
This section describes how to switch on and off the RTX8930 headset and how to register the unit on an RTX 8660 SME VoIP system.
How to Switch the Headset On/Off:
Vypínání náhlavní soupravyTo switch the headset off, long-press the AUX klíč spolu s VOL+ a VOL- keys (press and hold the three keys for five seconds). The blue LED will give a short blink before switching off.
Registration Initial Registration
Následné registraceIf the RTX8930 headset has already been registered on the same or another base system and needs to be re-registered, the required action is to press and hold the HOOK OFF klíč spolu s VOL+ a VOL- keys until the blue LED starts blinking fast.
POZNÁMKA: The blue LED will not start blinking in registration mode if the unit is cradled and charging. Please check the additional document via [2] for more information about terminal registration on a base system.
Call Operations
- Příchozí hovor As the headset receives an incoming call, a ringtone will be played back
- Odpověď na příchozí hovor Chcete-li přijmout příchozí hovor, stiskněte tlačítko HOOK OFF klíč
- Odmítnout příchozí hovor It is not currently possible to reject an incoming call
- Ukončení hovoru To end an ongoing call, press the HOOK OFF klíč
- Hlasitost a ztlumení It is possible to adjust the earpiece volume up or down during calls by pressing the VOL+ a VOL- keys, respectively. There are six volume steps. A beep is played back to indicate that the volume is adjusted. A higher frequency beep is played back when the volume cannot be adjusted further up or down.
- Vypnutí mikrofonu It is possible to mute the microphone during calls by pressing the ZTLUMIT key. The microphone is unmuted by pressing the ZTLUMIT key again. A voice prompt announcing “Mute on” is played back when mute is activated. A voice prompt announcing “Mute off” is played back when mute is deactivated.
Odstraňování problémů
- Headset doesn’t enter registration mode when re-registering: If you are cradled and charging, the blue LED will not start blinking fast in registration mode. Remove it from the cradle/charging and try again.
- No confirmation after switching on: Po stisknutí AUX, the blue LED should blink fast until a signal is detected. Once the headset locks onto a base, the voice prompt “Headset subscribed” should play and the LED should switch to blinking with a 2-second interval.
- Volume can’t be increased/decreased: The headset provides higher frequency beeps when the volume cannot be adjusted further up or down.
Dokumenty / zdroje
 | 8930 Wireless Dect Headset |
Reference
- Uživatelská příručkamanual.tools