MAGICAMENTE Kitchen Set Instructions

MAGICAMENTE Kitchen Set

Specifikace

• Značka: MAGICAMENTE
• Doporučený věk: 3+
• Země původu: Vyrobeno v Číně
• Materiály: Not specified, but includes plastic fasteners and various-sized screws (M4X44mm, M4X36mm, M4X15mm, M3X18mm).
• Obsah: Various numbered pieces (1-21) and accessories (25-28) as detailed in the ‘CONTENIDO’ and ‘ACCESORIOS’ sections of the manual.

Návod k použití

WARNING! Choking hazard – Small parts. Not suitable for children under 3 years.

The tableware is not intended to contact real food; please do not fill or contact real food.

Nutná montáž dospělých.

Poznámka 1:

Organize your parts.
Make sure you have all the required parts BEFORE starting the assembly!

• Please use a manual screwdriver for assembly, or set your electric screwdriver to the minimum torque to avoid damaging the product. If the minimum torque is not enough to turn the screws, gradually increase the torque as needed.
• Do not fully tighten the screws until all panels are connected.
• To complete the assembly, use a manual screwdriver to fully tighten all screws until they are secure.

Poznámka 2:

• The plastic fasteners are pre-installed. However, they may shift during transport. Please check whether the fasteners are correctly seated in the holes and adjust them if they are misaligned.
• The correct installation positions are as follows:

Seznam dílů

Před montáží:

1. Přečtěte si pokyny: Please read all instructions before assembling. Incorrect assembly could result in a hazard for the child.
2. Řazení dílů: Order your pieces. Make sure you have all the required parts BEFORE starting assembly!

Montážní tipy:

• Minimum Torque: Please use a manual screwdriver for assembly or adjust your electric screwdriver to MINIMUM TORQUE to avoid damaging the product. If the minimum torque is not sufficient to turn the screws, gradually increase the torque as needed.
• Do Not Fully Tighten Initially: ŠROUBY PLNĚ NEUTAHUJTE, DOKUD NEJSOU VŠECHNY PANELY SPOJENY.
• Konečné utažení: To complete assembly, use a hand screwdriver to fully tighten all screws until they are snug. DO NOT OVERTIGHTEN! Overtightening will cause the product to crack.
• Plastic Fasteners (Note 2): Plastic fasteners are pre-installed. However, they may shift during transport. Please check if the fasteners are correctly seated in the holes and adjust them if they are misaligned. The correct installation positions are shown in the diagram on  Pay attention to Note 2 in assembly steps B, E, H, I, J, K, L, O.

Montážní kroky:

Follow the diagrams and part numbers provided on

1. Krok A: Use parts 1, 20 (x2) and screws 27 (x2).
2. Step B (See Note 2): Use parts 3 and screws 26 (x2).
3. Krok C: Use parts 2, 6 (x2).
4. Krok D: Use parts 14 and screws 27 (x2).
5. Step E (See Note 2): Use parts 5 and screws 26 (x4).
6. Krok F: Use parts 4, 16, 19 and screws 28 (x2).
7. Krok G: Use parts 7, 11, 12 and screws 26 (x2).
8. Step H (See Note 2): Use parts 8, 9 and screws 25 (x2).
9. Step I (See Note 2): Use parts 13 (x2) and screws 25 (x4).
10. Step J (See Note 2): Use part 9 and screw 25.
11. Step K (See Note 2): Use part 15 and screw 25. Pozor! Before continuing to the next step, slightly loosen the screw on the back to regulate the turning force of the switches.
12. Step L (See Note 2): Use part 10 and screws 25 (x2).
13. Step M: Use parts 17, 18 (x2).
14. Step N: Use screws 26 (x6).
15. Step O (See Note 2): Use screws 26 (x4).
16. Step P: Use part 21.

Odstraňování problémů

• Product Damage During Assembly: If you notice cracking or damage, you may be overtightening screws. Loosen slightly and re-tighten gently. Always use minimum torque for power tools.
• Loose Parts/Wobbly Structure: Ensure all screws are fully tightened (but not overtightened) after all panels are connected. Check that plastic fasteners are correctly seated as per Note 2.
• Chybějící části: Refer to the ‘CONTENIDO’ and ‘ACCESORIOS’ sections to verify all parts are present before starting assembly. If parts are missing, contact the manufacturer.
• Difficulty Turning Screws: If using a manual screwdriver, apply firm, steady pressure. If using an electric screwdriver, gradually increase the torque from minimum if the screws are not turning.