JONSBO TK-5 Computer Case User Manual

Počítačová skříň JONSBO TK-5

Specifikace produktu

• Dimension: 474mm (D) x245mm (W) x539mm (H)
• Material: SGCC 1.0mm. plastic. Glass 4mm
• Drive Bay: 3.5 HDDx4 or 3.5 HDD×2,2.5 SSD×2 or 3.5 HDDx3,2.5 SSDx1
• Motherboard: ITX. M-ATX. ATX. M-ATX back plug. ATX back plug
• Rozšiřující slot PCI: 7
• Front I/0 Port: USB3.0×2. MIC & SPK×1. Type-Cx1
• PSU Support: ATX≤220mm
• Max. CPU Cooler Height: ≤180mm
• Max. Display Card Length: ≤460mm
• Fan: Top: 120mm*3 or 140mm*3 or 360 AlO (optional)
• Bottom: 120mm*3 or 140mm*3 (optional) Side: 120mm*3 (optional)Rear: 120mm*1 (optional)
• Weight: Standard version 10.72kg (net weight)

Seznam dílů

Schéma konektoru ukazuje pouze vztah posloupnosti linek. Funkce naleznete u skutečného produktu

INSTALACE

Remove the upper plate

• First loosen the thumb screws and push in the direction of the arrow to remove the upper plate.

Remove the glass side panel

1. Remove the 3 screws that secure the glass.
2. Lift in the direction of the arrow to remove the glass side panel.

Odstraňte pravý boční panel

Push outwards in the direction of the arrow to remove the right side panel.

Remove the right lower trim panel

Lift in the direction of the arrow to remove the right lower trim panel.

Instalace základní desky

Place the motherboard in the viewing installation area and fix it with screws.

Instalace grafické karty

1. Remove the PCI card strip and PCl cover.
2. Vložte grafickou kartu do slotu základní desky a zajistěte ji šrouby.

Instalace napájecího zdroje

Place the power supply into the installation area and lock it with screws.

3.5 Instalace HDD

1. Remove the hard drive bracket from the bottom of the chassis and lock the 3.5 HDD on the hard drive bracket.
2. The assembled hard disk bracket is screwed onto the chassis from the bottom of the chassis.

SSD Hard Drive Installation

1. The SSD hard drive is assembled with screws and washers.
2. Remove the hard drive bracket from the bottom of the chassis, place the assembled SSD into the corresponding hole, and push it forward into the card slot.
3. The assembled SSD hard drive bracket is locked to the chassis with screws from the bottom of the chassis.

Chladicí systém

Install a fan in the middle partition

1. Remove the screws that fix the middle partition and remove the middle partition.
2. Fix the fan to the middle partition with screws and then install it back into the chassis.

Top water cooling installation

1. Lock the fan on the water cooling radiator.
2. The water cooling radiator is fixed on the top cover of the chassis.

Instalace dokončena

1. Install the right lower trim panel in the direction indicated by the arrow.
2. Install the right side panel in the direction indicated by the arrow.
3. Install the glass from top to bottom and tighten the screws at the top.
4. Push the upper plate in the direction of the arrow and tighten the screws.

Dongguan Sibositong Industrial Co., Ltd.
No.5, Xinglong Lu, Sanzhong Village, Qingxi Town, Dongguan City, Guangdong Province, 523651, China © 2023 Dongguan Sibositong Industrial Co., Ltd. All rights reserved. Specifications are subject to change without prior notice. Some trademarks may be claimed as the property of others.