IOTmug SMD V3 4kanálový ovladač semaforů

Specifikace

• 4-kanálové relé
• Ovládání přes Wi-Fi s vlastní Wi-Fi sítí
• Ovládání přes přístupový bod
• Ovládejte více zařízení z jedné jednotky
• Expansion of the number of lights possible by adding another controller
• Omezení počtu cyklů
• Individuální manuální ovládání pro každou žárovku
• K dispozici jsou možnosti blesku
• Option to control the device using an existing Wi-Fi network
• On/Off control for all lights available with a single button press
• Ovládání klimatizace pomocí SMD relé
• Možnost obnovení továrního nastavení a možnost tvrdého obnovení továrního nastavení
• Tiché relé
• Téměř neomezený počet přepnutí
• Reverse option for Motions – Stop, Start, Pause, Resume options available as Software/Hardware

ELEKTROINSTALACE – Also see Image 11 below in the images gallery

• More resource: www.iotmug.com
• Need help with ASAP: support@iotmug.com

ZAPOJENÍ — Ovládání střídavých vedení / žárovek napájených ze zdroje střídavého proudu 

Glosář

• Pohyb: We use moƟon to activate any relay/device/lamp in a time cycle. You will see an M symbol next to each motion.
• MAC adresa: A unique address for each controller.
• Zařízení: Controlling multiple controllers from a single controller. We call Master and Slave / Client
• Blikat: Turn on/off any device frequently within a specified time period.
• Cyklus: You can set a limit for our cycle count. For example, if the cycle is set to 2, it means the controller will stop after running all motions 2 times. 0 means unlimited cycle count.
• Zvyk: Manually control each relay/device.
• Zastávka: Stop all motions.
• Start: Begin all motions.
• Turn On/Off ALL: This will turn on all relays. If any client controllers are connected to the master, it will also turn on the clients’ relays.
• SSID: If you want to connect your device to your WIFI network, you can use this.

Glosář

• Pohyb: We use motion to activate any relay/device/lamp in a time cycle. You will see the M symbol next to each motion.
• MAC adresa: A unique address for each controller.
• Zařízení: Controlling multiple controllers from a single controller. We call Master and Slave / Client
• Blikat: Turn on/off any device frequently within a specified time period.
• Cyklus: You can set a limit for our cycle count. For example, if the cycle is set to 2, it means the controller will stop aŌer running all motions 2 Ɵmes. 0 means unlimited cycle count.
• Zvyk: Manually control each relay/device.
• Stop: Stop all motions.
• Start: Begin all motions.
• Turn On/Off ALL: This will turn on all relays. If any client controllers are connected to the master, it will also turn on the clients’ relays.
• SSID: If you want to connect your device to your WIFI network, you can use this.

Další nápověda
Please check out our YouTube channel for detailed information: www.youtube.com/@IOTmug. You can also visit us at www.iotmug.com. If you would like a detailed video sent via email, please reach out to us at support@iotmug.com. Please describe what you would like to do, and we will be more than happy to assist you.

Základní instrukce
Each moƟon will have Start, End Time.

Motion/M      Seconds RED                7-12 YELLOW        5-7 GREEN           0-5

Napřample, in this scenario, the green light will be active from 0 to 5 seconds. Following that, the yellow light will be active from 5 to 7 seconds. Lastly, the red light will be active from 7 to 8 seconds. These light sequences will run in a continuous cycle. The minimum start time corresponds to the beginning of the cycle, and the maximum end time corresponds to the last point of the cycle.

How to Change the Light Controller Cycle

1. Power up your board, Image 11. Locate your device’s network in your device’s Wi-Fi settings. It will have a default name starting with “LC_********”. Connect to this network (Image 1). The default password is “12345678”
2. In any device’s browser (mobile or computer), type “192.168.4.1” and press Enter. Use the username “user” and password “123456” (Image 2).
3. You’ll be directed to the default motion settings in your browser (Image 3). These motions operate in a cycle/loop.
4. To add a new motion, click the “Add New Motion” button. Enter your settings and click “Add” (Image 4).
5. Modify existing motions by clicking on them (Image 5).
6. By default, channel turns on the defined motions. By the Reverse option, it will be turned off. (Image 12).
7. For manual relay control, click the “Custom” button to gain manual access (Image 6).
8. To limit the cycle count, adjust it on the motion screen and press “Save” (Image 7 shows an example of a 2-time run). Cycle 0 means unlimited.
9. For controlling multiple controllers, visit the Devices page. Add the MAC address of the client’s controller and provide a name (Image 8). You can find the MAC address of the desired devices on the motion page (image 3) or the “Print Mac Address” page.
10. Customize the device network name, default IP address, and add the device to your Wi-Fi network on the settings page. It supports 2.4GHz networks (Image 9).”
11. Factory Reset from Settings Page: To perform a factory reset, navigate to the settings page, scroll down, and select “Factory Reset.” Afterward, turn off the power, then turn it back on.
12. To reset the board to factory settings, ensure the device is powered off, then briefly connect the “I05” pin to GND. Turn the device on and wait for the green light to appear. Once the green light is visible, power off the device again and remove the jumper. Finally, turn the device back on, and it will be restored to its factory settings.
13. To enable wired Stop, Start, Pause, and Resume options, you need to create connections between the ground and the corresponding pin numbers. For example, to use the Stop function (pin 104), place a button between the Ground pin and the 104 pin. The other pin assignments are as follows: STOP (104), START (105), PAUSE (102), and RESUME (100). If you wish to

FAQ

Otázka: Kde najdu podrobné informace o zapojení a nastavení?

You can check out our YouTube channel at www.youtube.com/@IOTmug nebo navštivte naši webmísto na www.iotmug.com. For personalized assistance, contact us at support@iotmug.com.

Otázka: Jak provedu obnovení továrního nastavení nebo hard reset?
To perform a factory reset or hard reset, refer to the instructions provided in the manual or visit the Setup/Settings page on the device for detailed steps.

Dokumenty / zdroje

IOTmug SMD V3 4kanálový ovladač semaforů [pdfUživatelská příručka SMD V3, SMD V3 4kanálový ovladač semaforů, SMD V3, 4kanálový ovladač semaforů, ovladač semaforů, ovladač světel, ovladač

Reference

• Uživatelská příručka