Rozšiřující modul komunikace PROFIBUS-DP EC-TX803
“
Specifikace
- Working temperature: [specification]
- Storage temperature: [specification]
- Relative humidity: [specification]
- Running environment: [specification]
- Installation method: [specification]
- Ingress protection (IP) rating: [specification]
- Heat dissipation method: [specification]
- Communication rate: [specification]
- Network topology: [specification]
Konec produktuview
Popis modelu
Product model: EC-TX803
Distinguishing code: 803 (PROFIBUS-DP communication), TX
(communication module), EC (expansion module)
Popis součásti
| Žádný. | Jméno | Popis |
|---|---|---|
| 1 | STATUS indicator (green) | On: The expansion card is connected with the master device. Off: The expansion card is disconnected from the master zařízení. |
| 2 | FAULT indicator (red) | Blinking (On: 250ms; Off: 250ms): User parameter data is incorrect. Off: No fault. |
| 3 | Montážní upevňovací otvor | To fix the expansion module |
| 4 | PROFIBUS-DP communication port | For communication with the control box |
Instalace a elektroinstalace
Bezpečnostní opatření při instalaci
- Před instalací se ujistěte, že je zařízení vypnuté.
- Use any of the 3 expansion module interfaces on the control
krabice. - Recommended to install the PROFIBUS-DP expansion module at
expansion slot 3.
Pokyny k instalaci
- Place the expansion module in the corresponding position of the
control box expansion slot 3. - Align the positioning hole with the stud.
- Fix with an M3 screw to complete the installation.
FAQ
Q: What is the maximum number of nodes that can be
připojen?
A: When used, a maximum of 127 nodes (including repeaters and
master nodes) can be connected.
Otázka: Jakou normu výrobek splňuje?
A: The product complies with the fieldbus standard EN50170.
“`
Rozšiřující modul komunikace PROFIBUS-DP EC-TX803
EC-TX803 PROFIBUS-DP Communication Expansion Modules User Manual
1.2 Specifikace
EC-TX803 PROFIBUS-DP Communication Expansion Module Table 1-1 Specifications
Parameters Working temperature Storage temperature
Relative humidity Running environment Installation method Ingress protection (IP) rating Heat dissipation method Communication rate
Topologie sítě
Specification -1050 -2060.0 5%95% (No condensation) No corrosive gas Fixed with snap-fits and screws IP20 Natural air cooling 9.6k bit/s12M bit/s Linear bus with one active fieldbus terminal resistor on each end
1.3 Struktura
Figure 1-2 Structural diagram
1
3
5
Rozšiřující modul komunikace PROFIBUS-DP EC-TX803
2.2 Rozměry
The dimensions of the PROFIBUS-DP expansion module is 73.5 ×74×23.3 (W*H*D) mm, as shown in Figure 2-1.
Figure 2-1 Product outline and mounting dimensions diagram (unit: mm)
72
73.5
STATUS FAULT
23.3
74
Předmluva
Thank you for choosing INVT EC-TX803 PROFIBUS-DP communication expansion modules. EC-TX803 is a PROFIBUS-DP fieldbus communication module that needs to be used with the GD880 series VFD control box. The expansion module communicates with the bus master through PROFIBUS-DP communication protocol. This manual describes the product overview, installation, wiring, and commissioning instructions. Before installing the VFD, read through this manual carefully to ensure the proper installation and running with the excellent performance and powerful functions into full play. Product features: Communication rate: 9.6kbit/s12Mbit/s A maximum of 31 nodes can be connected when no repeater is used. If repeaters are
used, a maximum of 127 nodes (including the repeaters and master nodes) can be connected. Complies with the fieldbus standard EN50170
1 Konec produktuview
1.1 Popis modelu
Obrázek 1-1 Typový štítek produktu a označení modelu
Typový štítek
Manufacture No. Product model
XXXXXXXXXXXXXXX EC-TX803
Product model EC – TX 803
Distinguishing code 803: PROFIBUS-DP communication Module category TX: communication module Product category EC: expansion module
PLC1.ir
6
4
7
Tabulka 1-2 Popis součásti
Žádný.
Jméno
Popis
POSTAVENÍ
On: The expansion card is connected with the master device and
1
bus status data exchange can be performed.
indicator Off: The expansion card is disconnected from the master device.
(zelený)
On: The expansion module is offline and data exchange cannot
být proveden.
Blinking (On: 500ms; Off: 500ms): Configuration error occurs. The
length of the user parameter data set during the module
initialization is different from that during the network
CHYBA
konfigurace.
2 Fault indicator Blinking (On: 250ms; Off: 250ms): User parameter data is
(červený)
incorrect, The length or content of the user parameter data set
during the module initialization is different from that during the
konfigurace sítě.
Blinking (On: 125ms; Off: 125ms): An error occurs in the ASIC
initialization of PROFIBUS communication.
Vypnuto: Žádná chyba
3
Installation To fix the expansion module
upevňovací otvor
X1 –
4 communication PROFIBUS-DP communication port
přístav
5
Nameplate Including the model and sequence number of the expansion
modul
6
Connection For connection between the PROFIBUS-DP module and control
přístav
krabice.
Positioning To align the expansion module and control box for easy
7
otvor
instalace
2 Instalace a zapojení
2.1 Bezpečnostní opatření při instalaci
Před instalací se ujistěte, že je zařízení vypnuté.
Poznámka
Na ovládací skříni jsou 3 rozhraní rozšiřujícího modulu (rozšiřující slot 1, rozšiřující slot 2, rozšiřující slot 3). Můžete použít kterýkoli z těchto slotů podle skutečného zapojení.
It is recommended to install the PROFIBUS-DP expansion module at expansion slot 3.
Potřebné nářadí: křížový šroubovák PH1, rovný šroubovák SL3
Tabulka 2-1 Požadavky na utahovací moment šroubů
Velikost šroubu M3
Fastening torque 0.55 N·m
M3
2.3 Pokyny k instalaci
It is recommended to install the PROFIBUS-DP expansion module at expansion slot 3 of the control box. The following is an example of the installation at slot 3. Step 1 Place the expansion module in the corresponding position of the control box expansion slot 3, align it with the slot, and then buckle it together. Step 2 Align the expansion module positioning hole with the positioning stud. Step 3 Fix with a M3 screw. The installation is complete.
Expansion slot 1
Expansion slot 2
Expansion slot 3
Krok 1
Krok 2
Krok 3
Note: The expansion module and control box are electrically connected through slots. Please
install them in place. To ensure the reliable operation of the expansion module and meet EMC requirements,
please tighten the screws according to the recommended torque for reliable grounding.
2.4 Pokyny k demontáži
Modul můžete rozebrat obrácením pořadí kroků popsaných v části 2.3 Pokyny k instalaci.
Krok 1 Odpojte všechny zdroje napájení a demontujte všechny kabely připojené k rozšiřujícímu modulu.
Krok 2 Pomocí křížového šroubováku PH1 odstraňte zemnicí šrouby rozšiřujícího modulu.
Krok 3 Zvedněte rozšiřující modul z polohovacího čepu ovládací skříňky a vytáhněte jej do vhodné polohy. Demontáž je dokončena.
Rozšiřující modul komunikace PROFIBUS-DP EC-TX803
2.5 Uživatelská elektroinstalační svorka
Figure 2-2 Terminal diagram
Rozšiřující modul komunikace PROFIBUS-DP EC-TX803
3 Commissioning instruction
Figure 3-1 PROFIBUS-DP communication expansion module configuration flowchart Start
Table 2-2 D-type connector function definition
D-type connector
5
4
3
2
1
6
7
8
9
Kolík
Jméno
1
2
3
B-Line
4
RTS
5 GND_BUS
6
+5V BUS
7
8
A-Line
9
Housing SHLD
Popis Nepřipojeno
Unused Receive Date+ Request sending
GND +5V Not connected Receive DataNot connected Shielded cable
2.6 Opatření pro zapojení
The PROFIBUS-DP communication expansion module supports the standard 9-pin D-type connector. The electrical wiring diagram is shown in Figure 2-3.
Figure 2-3 PROFIBUS-DP bus connection diagram
Až do 31
Ovládací skříňka
Ovládací skříňka
PROFIBUS-DP
zvládnout
POSTAVENÍ
CHYBA
…
STATUS FAULT
Table 2-3 Transmission rates and corresponding transmission distances
Baud rate (kbps)
Transmission distance (m)
9.6
19.2
93.75 187.5 500 1500 12000
1200
1000
400
200
100
Poznámka:
Transmission distance in Table 2-3 refers to the distance without repeaters.
A maximum of 31 nodes can be connected when no repeater is used. If repeaters are used, a maximum of 127 nodes (including the repeaters and master nodes) can be connected.
Check the electrical connection between the PLC and the module
is proper.
Wait for the PLC and the control box to be powered on.
Set the node number of expansion module (P40.01) based on the system (The control box is repowered on after the node number is changed.)
Check P40.00 to
N
confirm whether the
module status is 1:
online.
Y
Configure other function codes.
Zkontrolujte, zda
N
STATUS indicator is
green (flashing).
Y End
Table 3-1 Function code parameters related to PROFIBUS-DP communication expansion module
Kód funkce
Jméno
Popis
Bit0: Online status of SLOT1 module
Bit1: Online status of SLOT2 module
Bit2: Online status of SLOT3 module
Bit3: Online status of SLOT2-1 module
Bit4: Online status of SLOT2-2 module
P40.00
Module Bit5: Online status of SLOT2-3 module online status Bit6: Online status of SLOT3-1 module
Bit7: Online status of SLOT3-2 module
Bit8: Online status of SLOT3-3 module
Online stav
0: Offline
1: Online
Uzel
P40.01
number of expansion
1
modul
0: Žádný
1: PROFIBUS-DP module
Bus adapter 2: PROFINET I/O module
P37.00 supporting 3: CANopen module
bus type 4: EtherNET module
5: Modul EtherCAT
6: Modul DeviceNet
Výběr kanálu dálkového ovládání
Remote 0: Bus adapter A
P02.00
control 1: Bus adapter B channel 2: MODBUS (address 0x4200, 0x4201)
selection 3: Terminal start/stop module (IN1,
IN2, IN3)
Setting range 0x000x1FF
1127 06 03
Default 0x00 1 1 0
Poznámka:
When two identical communication expansion modules are mounted at the same time, only the expansion module in the slot with a small label number is functional, while the other expansion module is used for redundancy. For example, when two DP expansion modules are inserted in slot 1 and slot 2 respectively, the DP module in slot 1 is valid.
For other parameter settings of the EC-TX803 PROFIBUS-DP expansion module, see software manuals of the GD880 series products.
PLC1.ir
Rozšiřující modul komunikace PROFIBUS-DP EC-TX803
Dokumenty / zdroje
 |
iNVT EC-TX803 PROFIBUS-DP Communication Expansion Module [pdfUživatelská příručka EC-TX803, EC-TX803 PROFIBUS-DP Communication Expansion Module, PROFIBUS-DP Communication Expansion Module, Communication Expansion Module, Expansion Module, Module |