Figure 1: HZXVOGEN MIG250DP Multi-Process Welder Overview - Showcasinklíčové vlastnosti a design.
1. Důležité bezpečnostní informace
Welding operations involve inherent risks. Always prioritize safety to prevent injury or damage. Read and understand all safety warnings and instructions before operating the HZXVOGEN MIG250DP welder.
- Elektrický šok: Může způsobit smrt. Nedotýkejte se elektrických částí pod napětím. Používejte suché svářečské rukavice a ochranný oděv. Zajistěte řádné uzemnění.
- Výpary a plyny: Může být nebezpečné pro vaše zdraví. Chraňte hlavu před výpary. Používejte dostatečné větrání nebo odsávání v místě oblouku.
- Obloukové paprsky: Can injure eyes and burn skin. Wear a welding helmet with a proper shade filter and protective clothing.
- Požár a výbuch: Welding sparks and hot metal can cause fire or explosion. Keep flammable materials away from the welding area. Have a fire extinguisher readily available.
- Popáleniny: Horký kov může způsobit těžké popáleniny. Nedotýkejte se horkých částí holýma rukama.
- Elektromagnetická pole (EMF): May interfere with pacemakers. Consult your doctor before welding.
The HZXVOGEN MIG250DP includes safety features such as a Voltage Reduction Device (VRD) and protection against overvoltage, overcurrent, overload, and overheating. However, these features do not replace proper safety practices.
Figure 2: Welder Safety Features - Illustrates the various protection systems integrated into the HZXVOGEN MIG250DP, including overcurrent, overvoltage, overheat, overload, electrostatic discharge protection, and IP21 waterproofing.
2. Konec produktuview
The HZXVOGEN MIG250DP is a versatile 6-in-1 multi-process inverter welding machine designed for various welding applications. It combines advanced digital control with robust safety features to deliver stable and precise welding performance.
2.1 Klíčové vlastnosti
- 6-in-1 Welding Capability: Supports MIG Gas, Flux Core MIG, Pulsed MIG, Lift TIG, Stick (MMA), and Aluminum welding.
- Enhanced Power and Reliability: Features a fully digital microcontroller and highly integrated circuit for stable and consistent welding results.
- Advanced Synergic Control: Automatically adjusts welding parameters for optimal performance across different materials like carbon steel, stainless steel, and thicker steel.
- Optimized Welds: Compensates for mains voltage fluctuations, reducing spatter, increasing penetration, and ensuring consistent wire feed.
- Komplexní bezpečnost: Equipped with Voltage Reduction Device (VRD) and protection against overvoltage, overcurrent, overload, and overheating. Features a unique cooling system for extended operation.
- Dual Voltage Vstup: Kompatibilní se zdroji napájení 110V i 220V.
Figure 3: Multi-Process Welding Modes - Displays the various welding processes supported by the MIG250DP, including Gas MIG, Flux Core MIG, Stick, Lift TIG, and Pulse MIG for aluminum.
2.2 Obsah balení
The HZXVOGEN MIG250DP package typically includes the following items:
- Pochodeň MIG
- Pozemní Clamp
- Návod k použití (tento dokument)
- Plynová hadice
- Hadice Clamp
- Držák elektrody
- Kartáčové kladivo
- Demolition Wrench
- Conductive Nozzle
- 0.8 mm Welding Wire
- Drátěné kolo
- Grafenová trubice
- 110V-220V Adapter
Figure 4: Included Accessories - A visual representation of the components supplied with the HZXVOGEN MIG250DP welding machine.
3. Nastavení a instalace
Správné nastavení je klíčové pro bezpečné a efektivní svařování. Pečlivě dodržujte tyto kroky.
3.1 Připojení napájení
- Ensure the welder's power switch is in the "OFF" position.
- Connect the power cord to a suitable 110V or 220V power outlet. The machine is designed for dual voltage vstup.
- Verify that the power source meets the welder's requirements.
3.2 Wire Spool Installation (MIG/Flux Core)
- Otevřete boční panel svářečky pro přístup k mechanismu podávání drátu.
- Place the wire spool onto the spool holder. Ensure it rotates freely.
- Thread the welding wire through the guide tube and into the drive roller groove.
- Close the drive roller tension arm and adjust the tension knob. The tension should be sufficient to feed the wire without slipping, but not so tight as to deform the wire.
- Ensure the correct drive roller size (e.g., 0.8mm, 1.0mm) is selected for your wire diameter.
Figure 5: Smooth Wire Feed System - Details the internal components for wire spool installation and feeding, emphasizing ease of setup.
Figure 6: Wire Feeding Mechanism - Shows the process of installing welding wire and ensuring smooth operation through the drive rollers.
3.3 Hořák a uzemnění Clamp Spojení
- Connect the MIG torch to the appropriate connector on the front panel. Ensure it is securely tightened.
- Připojte zem třamp cable to the designated terminal (usually negative for MIG/Flux Core, positive for Stick).
- Připojte zem třamp firmly to the workpiece or welding table, ensuring good electrical contact.
3.4 Gas Connection (for MIG Gas Welding)
- Connect one end of the gas hose to the gas inlet on the rear of the welder.
- Connect the other end of the gas hose to your gas cylinder regulator.
- Ensure all connections are tight to prevent gas leaks. Open the gas cylinder valve slowly.
4. Návod k obsluze
The HZXVOGEN MIG250DP offers multiple welding modes. Select the appropriate mode and adjust parameters according to your welding task.
4.1 Ovládací panel Overview
The welder features a large LED display and intuitive controls for mode selection and parameter adjustment.
Figure 7: Large LED Display - Provides clear digital readouts and indicators for selected welding modes and parameters.
Figure 8: Digital Control Interface - Highlights the precision and clarity of the digital display for setting welding parameters.
4.2 Výběr režimu a nastavení parametrů
- Turn on the welder using the power switch.
- Use the "Multi-function" or "Selection" buttons to cycle through the available welding modes (MIG Gas, Flux Core, Pulse, Lift TIG, MMA).
- In Synergic mode (SYN), simply select the current, and the machine will automatically match the voltage pro optimální výsledky.
- For experienced users, the voltage compensation feature allows for precise manual adjustment of voltage.
Figure 9: Synergic Mode Operation - Explains how the synergistic control simplifies parameter setting for beginners and offers fine-tuning for advanced users.
4.3 Welding Process Guidelines
Refer to the following table for recommended settings based on material thickness and welding process. These are starting points and may require fine-tuning.
Figure 10: Welding Parameter Chart - Provides a guide for selecting appropriate wire diameter and current for different materials and welding processes.
4.3.1 MIG Welding (Gas/Flux Core/Pulse)
- Select the desired MIG mode (Gas, Flux Core, or Pulse).
- Nastavení rychlosti a objemu podávání drátutage according to the material and thickness, or use Synergic mode.
- For Gas MIG, ensure gas flow is set correctly (e.g., 10-15 L/min for CO2 or Argon/CO2 mix).
- For Pulsed MIG (especially for aluminum), ensure the correct aluminum wire (e.g., 1.0mm/1.2mm) and a suitable spool gun are used.
Figure 11: Precision Welding Examples - Illustrates the quality of welds on different materials, including aluminum and mild steel.
Figure 12: Single Pulse Aluminum Welding - Shows the machine's capability for specialized aluminum welding with pulsed MIG.
4.3.2 Svařování obalenou elektrodou (MMA)
- Připojte držák elektrody ke kladnému (+) pólu a uzemňovacímu vodiči.amp na záporný (-) terminál.
- Vyberte režim MMA.
- Vložte příslušnou elektrodu do držáku.
- Adjust the current based on the electrode type and material thickness.
4.3.3 Svařování TIG s liftingem
- Connect a TIG torch (not included) to the appropriate terminal.
- Připojte zem třamp k obrobku.
- Vyberte režim Lift TIG.
- Adjust the current. Initiate the arc by gently touching the tungsten electrode to the workpiece and lifting it slightly.
Figure 13: Connection Setups for Various Modes - Illustrates how to connect accessories for Gas MIG, Flux Core MIG, Stick, and Lift TIG welding.
5. Údržba
Regular maintenance ensures the longevity and optimal performance of your HZXVOGEN MIG250DP welder.
- Čištění: Regularly clean the internal components, especially the fan and heat sinks, to prevent dust buildup and ensure efficient cooling. Use compressed air.
- Systém podávání drátu: Inspect the drive rollers and liner for wear or debris. Clean or replace as necessary to ensure smooth wire feeding.
- Hořák a kabely: Check the MIG torch, ground clamp, and electrode holder cables for damage, cuts, or loose connections. Replace damaged parts immediately.
- Kontaktní hroty a trysky: Replace worn contact tips and clean welding nozzles regularly to maintain arc stability and weld quality.
- Skladování: Pokud svářečku nepoužíváte, skladujte ji v čistém a suchém prostředí.
Figure 14: Internal Cooling System and Protection - Shows the internal components and cooling fan, emphasizing the importance of keeping them clear for optimal performance and highlighting integrated safety features.
6. Řešení problémů
This section provides solutions to common issues you might encounter. For problems not listed here, contact HZXVOGEN customer support.
| Problém | Možná příčina | Řešení |
|---|---|---|
| No power to the welder | Power switch off, loose power cord, tripped circuit breaker. | Ensure power switch is ON. Check power cord connection. Reset circuit breaker. |
| Žádný oblouk / Slabý oblouk | Poor ground connection, incorrect settings, worn contact tip, wrong wire size. | Zajistěte uzemněníamp is secure. Adjust current/voltage. Replace contact tip. Verify correct wire size. |
| Drát se nepodává plynule | Incorrect drive roller tension, clogged liner, tangled wire spool, wrong drive roller size. | Adjust drive roller tension. Clean or replace liner. Untangle wire. Ensure correct drive roller size. |
| Nadměrný rozstřik | Nesprávný svtage/wire feed speed, improper stick-out, dirty workpiece. | Adjust settings. Maintain proper stick-out. Clean workpiece thoroughly. |
| Aktivní indikátor přehřátí | Překročení pracovního cyklu, ucpané chladicí otvory, vysoká okolní teplota. | Allow welder to cool down. Ensure clear airflow to vents. Reduce welding time. |
7. Specifikace
| Funkce | Detail |
|---|---|
| Značka | HZXVOGEN |
| Model | MIG250DP |
| Rozměry produktu (D x Š x V) | 45 x 28 x 29 cm |
| Hmotnost | 11.8 kg |
| Vstupní objemtage | 230 voltů (dvojitý hlasitost)tage 110V/220V compatible) |
| Svařovací procesy | MIG Gas, Flux Core MIG, Pulsed MIG, Lift TIG, Stick (MMA), Aluminum Welding |
| Maximální výstupní proud | 250 A |
| Kompatibilita průměru drátu | Flux-cored: 0.8mm / 1.0mm; Aluminum: 1.0mm / 1.2mm |
| Bezpečnostní funkce | VRD, Overvoltage, Overcurrent, Overload, Overheating, Electrostatic Protection, IP21 |
Figure 15: Portable and Lightweight Design - Highlights the compact dimensions and manageable weight of the welder.
8. Oficiální produktová videa
No official product videos specifically for the HZXVOGEN MIG250DP model were available from the seller in the provided data. Please refer to the written instructions and diagrams for guidance.
9. Záruka a podpora
For warranty information, technical support, or service inquiries, please refer to the contact details provided with your purchase documentation or visit the official HZXVOGEN webUschovejte si doklad o koupi pro případ reklamace.
