1. Úvod
Thank you for choosing the FLARING FC650D PLUS Plasma Cutter. This advanced 65 AMP plasma cutting machine is designed for efficient and precise cutting of various metals. Featuring dual voltage compatibility (120V/240V), a high-frequency IGBT inverter, and a large digital display, it offers powerful performance and ease of use for both professionals and enthusiasts. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting to ensure optimal performance and longevity of your device.
Figure 1.1: FLARING FC650D PLUS Plasma Cutter and included accessories.
2. Bezpečnostní informace
Při obsluze plazmové řezačky vždy dbejte na bezpečnost. Nedodržení bezpečnostních pokynů může vést k vážnému zranění nebo poškození zařízení.
- Elektrický šok: Plazmové řezání zahrnuje vysoký objemtage. Ensure proper grounding. Do not operate in wet conditions. Wear dry gloves.
- Výpary a plyny: Cutting metals produces fumes and gases that can be hazardous. Work in a well-ventilated area or use local exhaust ventilation.
- Obloukové paprsky: The plasma arc produces intense visible and invisible (UV and IR) rays that can burn eyes and skin. Always wear appropriate welding helmet with a suitable shade filter, protective clothing, and gloves.
- Požár a výbuch: Sparks and hot metal can cause fires. Keep flammable materials away from the cutting area. Do not cut containers that have held combustible materials.
- Hluk: Plasma cutting can be noisy. Wear hearing protection.
- Horké díly: The torch and workpiece will become hot. Allow them to cool before handling or wear heat-resistant gloves.
- Stlačený vzduch: Ensure air compressor is properly maintained and regulated to the specified PSI.
- Osobní ochranné prostředky (OOP): Always wear appropriate PPE, including a welding helmet, flame-resistant clothing, heavy-duty gloves, and safety footwear.
3. Obsah balení
Ověřte, zda jsou všechny níže uvedené položky součástí balení. Pokud některé položky chybí nebo jsou poškozené, kontaktujte zákaznickou podporu.
- FLARING FC650D PLUS Plasma Cutter Unit
- PT31 Plasma Cutting Torch (4M)
- Pozemní Clamp with Cable (3M)
- Air Filter Regulator (Pre-installed)
- Additional Consumables (4 PCS)
- Power Adapter (for 120V connection)
- Návod k použití
Figure 3.1: All components included with the FC650D PLUS Plasma Cutter.
4. Konec produktuview a Specifikace
4.1. Klíčové vlastnosti
- 7th Generation 65A Touch Arc Plasma Cutter: High-frequency touch arc starting for efficient cutting.
- Dual Voltage (120 V/240 V): Automatický voltage adaptation for versatile use.
- Technologie IGBT invertorů: Provides stable and powerful cutting performance.
- Velký digitální displej: Real-time display of air pressure, voltage a aktuální.
- PA/2T/4T Functions: Offers control modes for various cutting needs.
- Přenosný a kompaktní: Lightweight design with a handle for easy transport.
4.2. Technické specifikace
| Specifikace | Hodnota |
|---|---|
| Model | FC650D PLUS |
| Vstupní objemtage | 120V/240V Dual Voltage |
| Max Current (120V) | 35A |
| Max Current (240V) | 65A |
| Clean Cut Thickness (120V) | 1/2" (12mm) at 35A, 50 PSI |
| Severance Cut Thickness (240V) | 5/8" (16mm) at 60A, 60 PSI |
| Recommended Breaker Size (240V) | 40A |
| Recommended Breaker Size (120V) | 55A |
| Required Air Compressor | 90 PSI, 60 L/min or above |
| Hmotnost položky | 14.92 libry |
| Rozměry balení | 17.5 x 11 x 9.7 palce |
| Zdroj napájení | AC |
Figure 4.1: Compact and lightweight design of the FC650D PLUS.
5. Pokyny k nastavení
5.1. Připojení napájení
The FC650D PLUS supports dual voltagvstup (120 V/240 V).
- For 240V operation, connect the main power cord directly to a compatible 240V outlet. Ensure the circuit breaker is rated for at least 40A.
- For 120V operation, use the provided power adapter to connect the main power cord to a 120V outlet. Ensure the circuit breaker is rated for at least 55A.
- Always ensure the power source is stable and properly grounded.
5.2. Připojení vzduchového kompresoru
A clean, dry air supply is crucial for optimal plasma cutting performance.
- Connect your air compressor to the air inlet on the back of the plasma cutter.
- The FC650D PLUS features a pre-installed air filter regulator. This regulator automatically senses and displays the air pressure on the digital screen, eliminating the need for an external gauge.
- Ensure your air compressor can provide a minimum of 90 PSI and 60 L/min airflow.
Figure 5.1: The pre-installed air regulator simplifies setup and displays pressure digitally.
5.3. Hořák a uzemnění Clamp Spojení
- Connect the PT31 plasma cutting torch cable to the designated port on the front panel of the machine. Ensure it is securely fastened.
- Připojte zem třamp cable to the ground terminal on the front panel.
- Připojte zem třamp firmly to the workpiece or a clean, bare metal surface that is electrically connected to the workpiece. A good ground connection is essential for safe and effective cutting.
6. Návod k obsluze
6.1. Zapnutí a digitální displej
Turn on the power switch located on the back of the unit. The large digital display will illuminate, showing real-time parameters.
Figure 6.1: The digital display provides real-time operational data.
- The display shows air pressure (PSI), output current (Amps) a objemtage.
- Indicators for Post Air, Pilot Arc, Air Pressure, Air Testing, 2T, and 4T functions are also present.
- Adjust the current using the control knob on the front panel to match your cutting requirements.
6.2. Understanding PA/2T/4T Functions
- PA (Post Air) Time: This function allows adjustment of the post-flow air time after the arc is extinguished. Proper post-air time helps cool the torch consumables, extending their lifespan.
- 2T (Two-Touch) Control: This is a semi-automatic cutting control mode. Press and hold the torch trigger to start the arc and cut. Release the trigger to stop. Ideal for short, quick cuts.
- 4T (Four-Touch) Control: This is an automatic cutting control mode. Press and release the torch trigger to start the arc and cut continuously. Press and release the trigger again to stop. This mode is suitable for long, continuous cuts, reducing operator fatigue and potentially leading to higher cutting quality with lower consumable wear.
6.3. Cutting Performance and Material Compatibility
The FC650D PLUS is capable of cutting various types of metal with precision.
Figure 6.2: Demonstrating clean cut and severance cut capabilities.
- Čistý řez: Up to 1/2 inch (12mm) at 35A (120V, 50 PSI). This refers to a cut with minimal dross and a smooth edge.
- Odstupné: Up to 5/8 inch (16mm) at 60A (240V, 60 PSI). This refers to the maximum thickness the machine can cut, though the quality of the cut may be reduced.
- The machine effortlessly cuts through rough, painted, and rusty surfaces while generating minimal slag.
Kompatibilní materiály:
- Kov
- Steels
- Hliníková deska
- Železo
- Nerez
- Legovaná ocel
- Měkká ocel
- Měď
Figure 6.3: The FC650D PLUS is suitable for a wide range of metal cutting applications.
7. Údržba
Regular maintenance ensures the longevity and optimal performance of your plasma cutter. Always disconnect the power before performing any maintenance.
- Kontrola spotřebního materiálu: Regularly inspect the torch consumables (electrode, nozzle, swirl ring, shield cup) for wear. Replace them when they show signs of degradation to maintain cut quality and prevent damage to the torch.
- Air Filter Regulator: Periodically check the water trap on the air filter regulator. Drain any accumulated moisture to ensure a dry air supply. Clean or replace the filter element if it becomes clogged.
- Chladicí systém: Ensure the cooling vents on the machine are clear of dust and debris to prevent overheating. Use compressed air to blow out dust from inside the machine if necessary (do this in a well-ventilated area).
- Kabely a připojení: Inspect all cables (power, torch, ground) for damage, cuts, or frayed insulation. Ensure all connections are tight and secure.
- Generální úklid: Keep the exterior of the machine clean. Wipe down with a dry cloth. Avoid using solvents that could damage the casing.
8. Řešení problémů
Tato část se zabývá běžnými problémy, se kterými se můžete setkat. V případě problémů, které zde nejsou uvedeny, se obraťte na zákaznickou podporu.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Stroj se nezapne. | Žádné napájení; vypnutý jistič; vadný napájecí kabel. | Check power connection, wall outlet, and circuit breaker. Ensure power cord is undamaged. |
| Žádný oblouk nebo slabý oblouk. | Nedostatečný tlak vzduchu; opotřebované spotřební materiály; špatné uzemnění; nesprávné nastavení proudu. | Verify air pressure (min 90 PSI); replace worn torch consumables; ensure ground clamp has good contact; adjust current setting. |
| Poor cut quality (excessive dross, rough cut). | Worn consumables; incorrect cutting speed; incorrect current/air pressure; torch too far from workpiece. | Replace consumables; adjust cutting speed; optimize current and air pressure settings; maintain proper torch standoff distance. |
| Air flows but no arc. | Torch trigger issue; internal fault; consumables not seated correctly. | Check torch trigger; reseat consumables; if problem persists, contact support. |
| Indikátor přehřátí zapnutý. | Machine has exceeded duty cycle; blocked cooling vents. | Allow machine to cool down; ensure cooling vents are clear. Reduce continuous cutting time. |
9. Záruka a podpora
FLARING products are manufactured to high-quality standards. For information regarding warranty coverage, technical support, or to purchase replacement parts and consumables, please refer to the warranty card included with your product or visit the official FLARING webmísto.
Můžete také navštívit FLARING Store on Amazon pro informace o produktech a podporu.
