Uživatelská příručka k rádiovému ovladači Jumper T14 2.4 GHz ELRS

1. Úvod

This manual provides comprehensive instructions for the safe and effective operation of your Jumper T14 2.4GHz ELRS Radio Controller. Please read this manual thoroughly before using the device to ensure proper setup, optimal performance, and to prevent damage or injury. Keep this manual for future reference.

2. Bezpečnostní informace

Always operate the radio controller in a safe and responsible manner. Failure to follow safety guidelines can result in property damage, serious injury, or even death.

• Prostředí: Operate in open areas, away from people, animals, and obstacles. Avoid flying near power lines, roads, or crowded places.
• Bezpečnost baterie: Use only recommended batteries. Do not overcharge or over-discharge. Store batteries in a fireproof bag.
• Předletové kontroly: Always perform a thorough pre-flight check of your aircraft and radio controller before each use.
• Firmware: Keep your radio controller's firmware updated to the latest stable version for optimal performance and security.
• Voda a vlhkost: Keep the radio controller away from water and high humidity.
• Děti: This product is not a toy. Keep out of reach of children under 16 years of age. Adult supervision is required for minors.

3. Konec produktuview

The Jumper T14 is a compact and ergonomic 2.4GHz ELRS radio controller designed for FPV drones and other RC applications. It features CNC Hall Gimbals, an OLED screen, and runs on EdgeTX firmware.

3.1. Radio System Components

Obrázek 3.1: Detailed diagram of the Jumper T14 Radio Controller, highlighting key components and controls on the front, back, and side views. This includes switches, dials, gimbals, screen, module compartment, and charging port.

• Přední panel:
  • VS-M CNC Hall Gimbals: High-precision gimbals for smooth control.
  • 2.42" OLED Screen: Clear display for EdgeTX interface.
  • Vypínač: Pro zapnutí/vypnutí jednotky.
  • Switches (2-position, 3-position): Configurable for various functions.
  • Dials (S1, S2): Rotary controls for fine adjustments.
  • Ořezávací tlačítka: For adjusting stick trims.
  • Tlačítko SYS: System menu access.
  • Tlačítko STRÁNKA: Page navigation.
  • Tlačítko RTN: Return/back button.
  • Stavové kontrolky: Provide operational feedback.
• Zadní panel:
  • Standard JR Module Compartment: For external RF modules.
  • External Cooling Fan: Helps dissipate heat from internal components.
  • Zásobník baterií: Pojme baterii.
• Side/Top Panel:
  • USB-C 10W Fast Charging Port: Pro nabíjení a datové připojení.
  • Tlačítko DFU: Device Firmware Upgrade mode button.
  • Trenérský port: For connecting to a simulator or another radio.
  • Okamžitý spínač: Spring-loaded switch.
  • Aretační spínač: Stays in position until toggled.
  • Adjustable and Foldable Antenna: Pro přenos signálu.
  • Reserved Antenna DIY Port: For custom antenna modifications.
  • Skládací rukojeť: For portability and comfortable grip.

3.2. Key Features Visuals

Obrázek 3.2: Přední view of the Jumper T14, showcasing the dual gimbals, OLED screen, and various control switches and dials.

Obrázek 3.3: Zadní view of the Jumper T14, showing the JR module bay, cooling fan, and battery compartment cover.

Obrázek 3.4: Detail of the USB-C port, used for charging the internal battery and connecting to a computer for firmware updates or simulator use.

Obrázek 3.5: Illustration highlighting the precision CNC Hall Sensor Gimbals, which provide accurate and durable control inputs.

Obrázek 3.6: Diagram illustrating the internal cooling fan system, designed to maintain optimal operating temperatures for the internal electronics.

Obrázek 3.7: View of the bi-directional foldable antennas, which can be adjusted for optimal signal transmission and folded for compact storage.

4. Nastavení

4.1. Instalace a nabíjení baterie

The Jumper T14 uses a rechargeable battery (not specified in input, assuming common RC battery types like 18650 or LiPo). Ensure the battery is fully charged before first use.

1. Open the battery compartment cover on the rear of the radio.
2. Insert the battery, ensuring correct polarity if applicable.
3. Bezpečně zavřete kryt bateriového prostoru.
4. Connect the supplied USB-C cable to the USB-C port on the top of the radio and to a compatible USB power adapter (e.g., 5V/2A).
5. The OLED screen or indicator lights will show charging status. Disconnect once fully charged.

4.2. Initial Power On and EdgeTX Setup

Upon first power-on, the radio will guide you through initial setup steps for the EdgeTX firmware.

1. Press and hold the Power Button until the OLED screen illuminates.
2. Follow the on-screen prompts to calibrate gimbals, set date/time, and configure basic radio settings.
3. Navigate menus using the scroll wheel and SYS/PAGE/RTN buttons.

4.3. ELRS Binding

To bind your Jumper T14 with an ELRS receiver, follow the standard ELRS binding procedure:

1. Ensure your ELRS receiver is powered on and in binding mode (typically by cycling power three times).
2. On the T14, navigate to the ELRS LUA script or the internal module settings within EdgeTX.
3. Select the "Bind" option. The radio will transmit a binding signal.
4. Once the receiver's LED indicates a successful bind (refer to your receiver's manual), the process is complete.

5. Návod k obsluze

5.1. Základní ovládací prvky

• Gimbaly: Control the primary movements of your aircraft (Throttle, Rudder, Aileron, Elevator).
• Přepínače: Used for arming, flight modes, special functions, etc. Assign functions in EdgeTX.
• Číselníky: Typically used for fine-tuning parameters like camera tilt, gain, or volume.
• Ořezávací tlačítka: Adjust the neutral position of the gimbals for stable flight.

5.2. Model Setup in EdgeTX

EdgeTX offers extensive customization for different models. Refer to the official EdgeTX documentation for detailed instructions on advanced model setup.

1. From the main screen, press the SYS button to enter the System menu.
2. Navigate to "Model Select" or "Model Setup" to create a new model or edit an existing one.
3. Configure internal or external RF module settings (e.g., ELRS protocol, power output).
4. Set up mixes, inputs, outputs, and special functions according to your aircraft's requirements.

6. Údržba

• Čištění: Use a soft, dry cloth to clean the radio controller. Avoid abrasive cleaners or solvents.
• Skladování: Store the radio in a cool, dry place, away from direct sunlight and extreme temperatures. Remove the battery if storing for extended periods.
• Aktualizace firmwaru: Regularly check for and install the latest EdgeTX firmware updates from the official EdgeTX webweb (www.edgetx.org) to ensure optimal performance and access to new features.
• Péče o gimbal: The CNC Hall Gimbals are durable, but avoid excessive force or impact. Keep them free from dust and debris.

7. Řešení problémů

8. Specifikace

9. Záruka a podpora

Informace o záruce a technickou podporu získáte od oficiálního zástupce společnosti ARRIS. webnebo se obraťte přímo na jejich zákaznický servis. Uschovejte si doklad o koupi pro případ reklamace.

Výrobce: propojka

Značka: ARRIS

Online podpora: Visit the ARRIS official website for FAQs, firmware downloads, and contact information. Obchod ARRIS na Amazonu