Zavedení
The Evenflo LiteMax 30 Infant Car Seat is designed to provide safety and comfort for infants weighing between 3 and 30 pounds. This manual provides essential information for proper installation, operation, maintenance, and troubleshooting to ensure the safe use of your car seat.
Figure 1: Evenflo LiteMax 30 Infant Car Seat, River Stone
Klíčové vlastnosti:
- Lehký design: Extremely lightweight for easy portability.
- Rozšířené použití: Accommodates infants from 3 to 30 lb.
- Nastavitelný postroj: Features 4 shoulder harness positions to adapt as your child grows.
- Ergonomická rukojeť: Navrženo pro pohodlné nošení.
- Full Coverage Canopy: Provides protection from sun, wind, and rain.
- Snadná instalace: Base equipped with a vehicle belt lock-off for quick and secure installation.
- Bezpečnostní normy: Meets or exceeds all applicable Federal Safety Standards, including structural integrity, rollover performance, and temperature testing.
Nastavení a instalace
Proper installation is crucial for your child's safety. Always refer to your vehicle's owner's manual for specific car seat installation instructions and locations.
Installing the Car Seat Base:
- Place the car seat base on the vehicle seat in a rear-facing position. Ensure it is level.
- Route the vehicle's lap belt or LATCH system through the designated belt path on the base.
- Engage the vehicle belt lock-off mechanism to secure the base tightly. The base should not move more than one inch side-to-side or front-to-back at the belt path.
- Verify the recline angle using the built-in recline indicator on the base. The indicator should be within the acceptable range for your infant's weight.
Figure 2: Securing the car seat base with the vehicle belt lock-off.
Figure 3: Recline indicator and harness adjustment points.
Attaching the Infant Carrier to the Base:
- Zarovnejte dětskou nosič se základnou.
- Lower the carrier onto the base until it clicks securely into place.
- Always check that the carrier is firmly attached to the base by lifting it slightly.
Ovládání autosedačky
Placing Your Child in the Car Seat:
- Unbuckle the harness and loosen the shoulder straps.
- Place your infant in the car seat with their back flat against the seat back.
- Přetáhněte popruhy bezpečnostního pásu přes ramena dítěte a mezi jeho nohy.
- Buckle the crotch buckle, then connect the chest clip. The chest clip should be positioned at armpit level.
- Utáhněte popruhy bezpečnostního pásu, dokud nebudou těsně přiléhat k tělu dítěte. Přebytečné popruhy by neměly být možné přiskřípnout. webbing na rameni.
Figure 4: Infant properly secured in the car seat harness.
Nastavení stříšky:
The full-coverage canopy can be adjusted by pulling it forward or pushing it back to shield your child from the elements.
Figure 5: Car seat with canopy extended for protection.
Údržba a péče
Pokyny pro čištění:
- Fabric Pads: The fabric pads are removable and machine washable. Use cold water and a gentle cycle. Tumble dry on low heat or air dry. Do not use bleach.
- Popruhy postroje: Otřete popruhy bezpečnostního pásu reklamouamp látku. Neperte v pračce ani neponořujte popruhy do vody, mohlo by to oslabit webbing.
- Plastové a kovové díly: Plastové a kovové části otřete měkkým hadříkemamp hadříkem a jemným mýdlem. Nepoužívejte abrazivní čisticí prostředky nebo rozpouštědla.
Figure 6: Cleaning the car seat fabric and base.
Skladování:
Store the car seat in a cool, dry place away from direct sunlight when not in use for extended periods.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Car seat base is loose after installation. | Vehicle belt not tight enough or lock-off not engaged. | Re-read installation instructions. Ensure vehicle belt is pulled taut and the lock-off is fully engaged. Apply pressure to the base while tightening. |
| Popruhy postroje se obtížně utahují nebo povolují. | Straps may be twisted or obstructed. | Check for twists in the harness straps. Ensure no fabric or clothing is obstructing the harness mechanism. |
| Infant carrier does not click securely into the base. | Nesprávné zarovnání nebo překážka. | Ensure the carrier is properly aligned with the base's connection points. Check for any debris obstructing the connection. |
If you encounter issues not covered here or require further assistance, please contact Evenflo ParentLink Consumer Care.
Specifikace
| Funkce | Detail |
|---|---|
| Rozměry produktu | 28.5 x 19 x 24 palce (72.4 x 48.3 x 61 cm) |
| Číslo modelu položky | CS100112042 |
| Doporučená maximální hmotnost | 30 liber (13.6 kg) |
| Doporučená minimální hmotnost | 3 liber (1.4 kg) |
| Typ materiálu | 100% Polyester |
| Počet poloh pro sklápění | 4 |
| Typ postroje | 5-bodový |
| Orientace | Směrem dozadu |
| Hmotnost položky | 8.17 libry (3.7 kg) |
Obrázek 7: Diagram rozměrů produktu.
Informace o záruce
Evenflo products are manufactured with quality and durability in mind. For specific warranty details, including coverage period and terms, please refer to the warranty card included with your product packaging or visit the official Evenflo webUschovejte si doklad o koupi pro případ reklamace.
Zákaznická podpora
Evenflo is committed to providing excellent customer service. If you have questions about your LiteMax 30 Infant Car Seat, need assistance with installation, or require support, please contact our ParentLink Consumer Care Team.
- Online podpora: Visit the Evenflo webweb s nejčastějšími dotazy a zdroji podpory.
- Live Video Support: Evenflo offers live video support with certified car seat safety technicians to assist with proper vehicle installation. This service can help you install your car seat with confidence.
- Kontaktní údaje: Refer to the contact details provided in your product packaging or on the official Evenflo webweb s telefonními čísly a e-mailovou podporou.
For more information about Evenflo products and services, you can visit the Evenflo Store on Amazon.
