1. Úvod
The EPEVER XTRA4210N-G3 MPPT Solar Charge Controller is an advanced maximum power point tracking (MPPT) device designed for off-grid photovoltaic systems. It efficiently manages power from solar panels to charge various battery types, including Sealed, Gel (AGM), Flooded, LiFePO4, and Li(NiCoMn)O2 batteries. This controller features a common negative grounding design, ensuring compatibility with diverse applications such as communication base stations, household systems, street lighting, and RV solar setups.
Key features include high tracking efficiency up to 99.5%, peak conversion efficiency of 98%, and an ultra-quiet design. The G3 version introduces independent voltage regulation, allowing direct load connection even without a battery, and enhanced protection mechanisms for system integrity.
Obrázek 1: Přesview of EPEVER XTRA-N-G3 MPPT Solar Charge Controller features.
2. Nastavení a instalace
Proper installation is crucial for the safe and efficient operation of your EPEVER XTRA4210N-G3 controller. Follow the connection sequence carefully.
2.1 Pořadí připojení
- Připojte baterii k ovladači.
- Připojte zátěž k regulátoru.
- Connect the PV array (solar panels) to the controller.
Pořadí odpojení: To disconnect the system, reverse the connection order: first disconnect the PV array, then the load, and finally the battery.
Figure 2: Recommended connection and disconnection order for the solar system components.
2.2 Wiring Recommendations
- The cable length for the battery should not exceed 3 meters.
- The recommended cable length for the PV array should not exceed 3 meters. If the PV array cable length is less than 3 meters, the system meets EN/IEC61000-6-3 requirements. If it exceeds 3 meters, the system may not meet these requirements.
- Controller Terminals: #6AWG (16mm²).
- Recommended Wire Cable: #8AWG (10mm²).
Figure 3: Connection diagrams for both No-battery Mode and Battery Mode configurations.
2.3 Překročení systémuview
The controller supports 12V/24V DC auto-work for lead-acid batteries and manual selection for lithium battery systems. It can handle a maximum PV input power of 520W for a 12V battery system or 1040W for a 24V battery system, with a maximum PV open circuit voltage of 100V (at minimum operating environment temperature) or 92V (at 25°C environment temperature).
Figure 4: System capabilities including PV input power, supported battery types, and MPPT charging characteristics.
3. Návod k obsluze
3.1 MPPT Algorithm and Adaptive Charging
The XTRA4210N-G3 utilizes a revolutionary MPPT algorithm that enhances tracking and response speeds, reduces losses, and minimizes downtime. It improves efficiency across various power segments and optimizes energy extraction in all scenarios. The adaptive charging features stages like bulk, boost, equalize, and float, which optimize battery health, lifespan, and overall performance.
Figure 5: MPPT algorithm and adaptive charging stages for optimal battery charging.
3.2 Výběr typu baterie
The controller supports multiple battery types. For Lead-acid batteries (Sealed, Gel, Flooded), you can select the type directly. For Lithium batteries (LiFePO4, Li(NiCoMn)O2), or custom user settings, parameters need to be configured via accessories like MT50 (remote meter), BLE/WiFi Adapter (APP), eLOG01, or PC software via the RS485 interface.
Figure 6: Supported battery types and methods for setting lithium battery parameters.
3.3 Display and Control Interface
The controller features a three-color LED indicator and an LCD display to show PV, Battery, and Load working status intuitively. Five buttons allow for easy adjustment and browsing of system parameters.
Figure 7: Controller display interface and battery type selection options.
3.4 Režimy provozu zatížení
The controller offers various load control modes, including Manual, Light ON/OFF, Light ON plus Timer, and User-defined settings. These modes allow for flexible management of connected loads based on user requirements and environmental conditions.
Figure 8: Load working modes for flexible power management.
4. Údržba
Regular maintenance ensures the longevity and optimal performance of your solar charge controller and battery system.
4.1 Stav baterie
The controller's adaptive charging stages (bulk, absorption, float, equalization) are designed to prolong the lifecycle of batteries. Ensure correct battery type selection and parameter settings, especially for lithium batteries, to maintain optimal charging conditions.
4.2 Ochrana systému
The controller includes all-around electronic protection against reverse polarity, overcharging, over-discharging, overload, short-circuiting, and reverse current. These features protect the battery from being over-charged by solar modules and over-discharged by loads. Periodically inspect all connections for tightness and corrosion.
4.3 Environmentální hlediska
The controller has a dustproof and waterproof design with IP33 enclosure, making it suitable for various environments. However, ensure it is installed in a well-ventilated area, away from direct sunlight and excessive moisture, to prevent overheating and ensure optimal performance.
5. Řešení problémů
This section provides guidance on common issues and protective measures.
5.1 Output Overcurrent Protection
The XTRA4210N-G3 controller features intelligent overcurrent detection and dynamic load management. It quickly detects and responds to excessive current, adjusting output in milliseconds to prevent system overload and ensure continuous operation. This protects the solar system from damage due to overcurrent events.
Figure 9: Comparison of overcurrent protection in a typical system versus the XTRA-N G3 controller.
5.2 Battery Management System (BMS) Disconnection
The G3 version's constant voltage output and limited current features ensure the system runs smoothly even if the BMS disconnects the battery. This protects connected equipment and loads from interruption and potential damage.
5.3 Problémy s komunikací
If experiencing issues with remote monitoring or parameter adjustment, ensure that communication accessories (e.g., BLE/WiFi Adapter, RS485 cable) are correctly connected and configured. Check the respective mobile app or PC software for error messages or connection status.
6. Specifikace
6.1 Mechanické parametry
| Položka | XTRA3210N | XTRA3215N XTRA4210N | XTRA3415N XTRA4215N | XTRA4415N |
|---|---|---|---|---|
| Dimenze | 230×165×63 mm | 255×185×67.8 mm | 255×187×75.7 mm | 255×189×83.2 mm |
| Montážní rozměr | 173 × 156 mm | 200 × 176 mm | 200 × 178 mm | 200 × 180 mm |
| Velikost montážního otvoru | Φ5 mm | |||
| Terminál | 6AWG (16 mm²) | |||
| Doporučený kabel | 8AWG (10 mm²) | |||
| Hmotnost | 1.31 kg | 1.70 kg | 2.07 kg | 2.47 kg |
| Osvědčení | EN/IEC62109-1, EN61000-6-3/EN61000-6-1, 47 CFR Part 15, Subpart B, IEC62509, IEC62321-3-1 | |||
Figure 10: Mechanical parameters and available accessories for the XTRA series.
6.2 Electrical Parameters (XTRA4210N-G3)
| Položka | XTRA4210N |
|---|---|
| Jmenovitý systém objtage | 12/24VDC automatický provoz |
| Jmenovitý nabíjecí proud | 40A |
| Jmenovitý vybíjecí proud | 40A |
| Vstup baterie objtage rozsah | 8~32V |
| Max. FV otevřený okruh objtage | 100V (at min operating environment temp); 92V (at 25°C environment temp) |
| MPPT svtage rozsah | V(BAT+2V)~72V |
| Max. FV vstupní výkon | 520W/12V; 1040W/24V |
| Typ baterie | Sealed / Gel / Flooded / LiFePO4 / Li-NiCoMn / User Lithium battery (LiFePO4 / Li-NiCoMn / User) |
| Dimenze | 255×185×67.8 mm |
| Terminály | 6AWG (16 mm²) |
| Čistá hmotnost | 1.70 kg |
Figure 11: Electrical parameters for the XTRA series solar charge controllers.
7. Záruka a podpora
For warranty information, please refer to the documentation provided with your purchase or contact the authorized EPEVER seller, Goland Century. The product is CE certified (LVD EN/IEC62109, EMC EN61000-6-1/3).
EPEVER offers various accessories to enhance monitoring and control:
- Dálkový měřič (MT50): For remote monitoring and real-time parameter configuration.
- Kabel USB-RS485 (CC-USB-RS485-150U): For monitoring and configuration via PC software.
- WiFi 2.4G Adapter (EPEVER-WiFi-2.4G-RJ45-D): Compatible with mobile app or cloud platform for wireless monitoring and parameter configuration via WiFi signal.
- Bluetooth adaptér (EPEVER-BLE-RJ45-D): Compatible with mobile app for wireless monitoring and parameter configuration via Bluetooth signal.
- Serial Device Server (EPEVER TCP 306): Compatible with mobile app or cloud platform via TCP network communication for remote wireless monitoring. LAN monitoring can be achieved using PC configuration tools and PC software.
- 4G Wireless Data Transmission Terminal (EPEVER RTU 4G HC01): Compatible with mobile app or cloud platform via a GSM or GPRS SIM card for remote wireless monitoring.
- Remote Temperature Sensor (RT-MF58R47K3.81A): For accurate control and protection of charging and discharging by collecting real-time battery temperature.
Video 1: EPEVER MPPT Solar Charge Controller XTRAN G3 Version overview. This video provides a brief introduction to the features and advancements of the G3 series controller.
Video 2: EPEVER MPPT Solar Charge Controller G3 Version XTRAN detailed features. This video offers a more in-depth look at the functionalities and benefits of the G3 series controller.
