Zavedení
This manual provides essential instructions for the proper installation, use, and maintenance of your Evenflo NurtureMax Infant Car Seat Base. This base is designed to be used exclusively with the Evenflo NurtureMax Infant Car Seat for children weighing between 4 and 22 lbs (1.8 to 10 kg) and with a height between 19 and 29 inches (48 to 74 cm).
The Evenflo NurtureMax Infant Car Seat Base meets or exceeds all applicable federal safety standards. For additional support, Evenflo offers ParentLink customer service with certified car seat safety technicians.
Důležité bezpečnostní informace
VAROVÁNÍ: Nedodržení těchto pokynů může vést k vážnému zranění nebo smrti vašeho dítěte.
- Always read and understand the complete instruction manual before installing or using the car seat base.
- This base is for rear-facing use only with the compatible Evenflo NurtureMax Infant Car Seat.
- Never use this car seat base without the Evenflo NurtureMax Infant Car Seat properly secured.
- Ensure the base is securely installed in your vehicle using either the lower anchor system (LATCH) or the vehicle's seat belt.
- Do not use a car seat base that has been involved in a crash, even if it appears undamaged. Replace it immediately.
- Register your car seat base with Evenflo to receive important safety notices and recalls.
Components of the Car Seat Base
Familiarize yourself with the parts of your Evenflo NurtureMax Infant Car Seat Base.
Obrázek 1: Přední strana view of the Evenflo NurtureMax Infant Car Seat Base. This image shows the overall shape and structure of the base.
Obrázek 2: Strana view of the Evenflo NurtureMax Infant Car Seat Base, highlighting its profile a mechanismus sklápění.
Obrázek 3: Spodní část view of the Evenflo NurtureMax Infant Car Seat Base, showing the routing paths for vehicle seat belts and lower anchor straps, along with instructional labels.
The base features a level line indicator to ensure correct installation angle and multiple recline positions for your child's comfort and safety.
Nastavení a instalace
The Evenflo NurtureMax Infant Car Seat Base can be installed using either the vehicle's lower anchor system (LATCH) or the vehicle's seat belt. Always refer to your vehicle owner's manual for specific car seat installation instructions and locations of LATCH anchors.
1. Preparing the Base
- Place the car seat base on the vehicle seat where it will be installed.
- Adjust the recline position of the base to achieve the correct angle. The base has 4 reclining positions. Refer to the level line indicator on the side of the base to ensure it is within the acceptable range for your child's weight and height.
Figure 4: The Evenflo NurtureMax Infant Car Seat Base positioned on a vehicle seat, ready for installation.
2. Installation using Lower Anchors (LATCH)
- Locate the lower anchors in your vehicle's seat. These are typically found in the crease between the seat back and bottom cushion.
- Attach the lower anchor connectors from the car seat base to the vehicle's lower anchors. Ensure both connectors are securely latched.
- Press down firmly on the car seat base while pulling the LATCH strap to tighten it. The base should not move more than 1 inch (2.5 cm) side-to-side or front-to-back at the belt path.
- Verify the level line indicator is correct.
3. Installation using Vehicle Seat Belt
- Protáhněte pánevní a ramenní pás vozidla vyznačenou dráhou pásu na základně autosedačky.
- Zapněte si bezpečnostní pás vozidla.
- Press down firmly on the car seat base while pulling the shoulder portion of the vehicle seat belt to remove all slack. If your vehicle seat belt has a locking mechanism (retractor or locking clip), engage it according to your vehicle's manual.
- The base should not move more than 1 inch (2.5 cm) side-to-side or front-to-back at the belt path.
- Verify the level line indicator is correct.
Operating the Car Seat Base
Once the base is securely installed, you can attach and detach the Evenflo NurtureMax Infant Car Seat.
Figure 5: The Evenflo NurtureMax Infant Car Seat Base with the compatible infant car seat attached (car seat shown faded for illustration).
Figure 6: The Evenflo NurtureMax Infant Car Seat securely attached to its base in a vehicle, demonstrating proper fit.
Připevnění dětské autosedačky
- Zarovnejte dětskou autosedačku se základnou.
- Lower the car seat onto the base until you hear an audible "click," indicating it is securely latched.
- Always check that the car seat is firmly attached to the base by lifting the car seat handle. It should not lift off the base.
Odpojení dětské autosedačky
- Locate the car seat release handle or button, typically at the back or front of the car seat.
- Press or pull the release mechanism while simultaneously lifting the infant car seat straight up from the base.
Údržba a péče
Proper care ensures the longevity and safety of your car seat base.
- Čištění: Do not lubricate or immerse any part of this child restraint in water, unless rinsing is permitted. Plastic and metal parts may be wiped clean with mild soap and water and dried with a soft cloth. The harness (if applicable to the car seat, not the base) can be wiped clean with mild soap and water. Allow harness to air dry. Machine wash the seat pad separately in cold water, delicate cycle. Tumble dry 10 to 15 minutes on low heat.
- Skladování: Pokud základnu autosedačky nepoužíváte, skladujte ji na chladném a suchém místě mimo dosah přímého slunečního záření.
- Inspekce: Regularly inspect the base for any signs of damage, wear, or missing parts. Contact Evenflo customer service if you notice any issues.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Base moves more than 1 inch (2.5 cm) | Not tightened sufficiently; incorrect belt path. | Re-install the base, ensuring the LATCH strap or vehicle seat belt is pulled as tight as possible while pressing down on the base. Verify the belt path is correct. |
| Infant car seat does not click into base | Nesprávné zarovnání; překážka. | Ensure the car seat is properly aligned with the base's connectors. Check for any obstructions preventing a secure connection. |
| Level line indicator is not correct | Incorrect recline angle. | Adjust the recline mechanism on the base until the level line indicator is within the acceptable range. |
If you continue to experience issues, please contact Evenflo ParentLink customer service for assistance.
Specifikace
Figure 7: Dimensions of the Evenflo NurtureMax Infant Car Seat Base: 11 inches (28 cm) height, 21.5 inches (54.6 cm) length, 13.5 inches (34.3 cm) width.
- Číslo modelu: CS900210000
- Rozměry produktu: 11 x 18 x 28 palce (28 x 45.7 x 71.1 cm)
- Hmotnost položky: 3.8 libry (1.72 kg)
- Minimum Child Weight: 4 libry (1.8 kg)
- Maximální hmotnost dítěte: 22 libry (10 kg)
- Minimum Child Height: 19 palců (48 cm)
- Maximální výška dítěte: 29 palců (74 cm)
- Typ materiálu: Polyester
- Materiálové složení: Base: Pp 46.65%, Pom 5.97%, Steel 42.44%, Pa 0.39%, Al 0.10%, Safety System 4.40%
- Počet poloh pro ležení: 4
- Typ instalace: Latch or Seat Belt
- Orientace: Rear Facing (Note: Infant car seat bases are designed for rear-facing use only, despite any conflicting data.)
Podpora a záruka
Evenflo is committed to providing safe and reliable products. For assistance with installation, product questions, or warranty information, please contact Evenflo ParentLink customer service.
Evenflo ParentLink Customer Service:
- Online support and live video assistance with certified car seat safety technicians are available. Visit the official Evenflo webstránky s kontaktními údaji a zdroji podpory.
- Product registration is recommended to receive important safety updates and recall information.
For detailed warranty terms and conditions, please refer to the documentation included with your purchase or visit the Evenflo official webmísto.
