ID-COOLING FX240 INF 240mm Liquid CPU Cooler Instruction Manual

1. Úvod

This manual provides detailed instructions for the installation, operation, and maintenance of your ID-COOLING FX240 INF 240mm Liquid CPU Cooler. Please read this manual thoroughly before installation to ensure proper setup and optimal performance. This All-In-One (AIO) liquid cooler is designed to provide efficient thermal management for your CPU, featuring a 240mm radiator, two 120mm daisy-chained fans, and an ARGB infinity mirror pump.

Image 1.1: ID-COOLING FX240 INF 240mm Liquid CPU Cooler components.

2. Konec produktuview

2.1 Obsah balení

Ověřte, zda jsou v balení přítomny všechny komponenty:

• 240mm Radiator with Integrated Pump
• 2x 120mm Cooling Fans
• Mounting Hardware for Intel Sockets (LGA1851/1700/1200/115X)
• Montážní hardware pro patice AMD (AM5/AM4)
• Thermal Paste Tube
• 7-pin Extension Cable for Fan/ARGB Connectivity

2.2 Klíčové vlastnosti

• Premium AIO Cooling: Designed for gaming and high-performance computing systems with a TDP of 300W.
• Powerful GEN 7 Pump: Operates at 2900RPM±10% for efficient heat dissipation.
• Upgraded Radiator: Features 12 waterways and a high-density fin stack, increasing cooling surface by 37% for improved heat transfer and liquid volume.
• Quiet 120mm Fans: Two fans deliver stable performance with a maximum noise level of 27.2dB(A).
• Infinity Mirror ARGB: The pump head features an addressable RGB infinity mirror effect.
• Jednoduchá správa kabelů: Fans utilize daisy-chain connectors and a 7-pin extension cable for streamlined wiring.
• 360° Rotatable Pump Cap: Allows for multi-angle adjustments without repositioning the cold plate.

Image 2.1: The infinity mirror effect on the pump head.

Image 2.2: Diagram illustrating the GEN 7 water pump with 2900 RPM speed and 3-phase, 6-pole motor.

Image 2.3: Two 120mm cooling fans installed in a PC case.

Image 2.4: Illustration of the daisy-chain fan connectors and 7-pin extension cable for simplified wiring.

Image 2.5: The pump cap can be rotated 360 degrees for optimal orientation.

3. Specifikace

4. Nastavení a instalace

Before beginning, ensure your system is powered off and disconnected from the power source. Refer to your motherboard manual for specific socket information.

4.1 Připravte základní desku

1. Identify your CPU socket type (Intel or AMD).
2. Install the appropriate backplate (if required for your socket) on the rear of the motherboard.
3. Attach the correct mounting standoffs to the motherboard's CPU socket holes.

Image 4.1: Various mounting brackets and hardware for Intel and AMD platforms.

4.2 Instalace chladiče a ventilátorů

1. Mount the two 120mm fans to the radiator using the provided screws. Ensure the fan airflow direction is appropriate for your case (typically exhausting air out of the case).
2. Install the radiator assembly into your PC case. Common mounting locations include the top or front of the case. Secure it with the appropriate screws.

4.3 Apply Thermal Paste and Mount Pump

1. Clean the CPU surface and the cold plate of the pump.
2. Apply a small amount of the included thermal paste to the center of your CPU. A pea-sized dot is generally sufficient.
3. Carefully place the pump assembly onto the CPU, aligning the mounting holes with the standoffs.
4. Secure the pump with the appropriate retention brackets and screws. Tighten screws in a diagonal pattern until snug, but do not overtighten.

Image 4.2: Proper application of thermal paste to the CPU surface.

4.4 Cable Management and Connections

1. Connect the daisy-chained fan cables to the 7-pin extension cable.
2. Connect the 4-pin fan connector from the extension cable to a CPU_FAN or PUMP_FAN header on your motherboard.
3. Connect the 3-pin ARGB connector from the extension cable to a 5V ARGB header on your motherboard. Poznámka: Do not connect to a 12V RGB header, as this may damage the LEDs.
4. Connect the pump's power cable to a dedicated AIO_PUMP or PUMP_FAN header on your motherboard. This is typically a 3-pin DC header. Ensure your motherboard BIOS is configured for voltage control on this header if it is not a 4-pin PWM header, to allow for proper pump speed control.
5. Route all cables neatly to ensure proper airflow and aesthetics.

Image 4.3: The ID-COOLING FX240 INF cooler fully installed within a PC case.

5. Návod k obsluze

5.1 První zapnutí

After installation, power on your system. The fans and pump should begin operating, and the ARGB lighting on the pump and fans should illuminate.

5.2 Konfigurace BIOSu/UEFI

Access your motherboard's BIOS/UEFI settings to:

• Ensure the CPU_FAN or PUMP_FAN header is set to PWM mode for the fans.
• Ensure the AIO_PUMP or PUMP_FAN header connected to the pump is set to DC/Voltage control mode, if applicable, to allow for proper pump speed regulation. Set the pump to run at 100% or a high fixed speed for optimal cooling.
• Monitor CPU temperatures to confirm effective cooling.

5.3 ARGB Control

The Addressable RGB (ARGB) lighting can be controlled via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) or a dedicated ARGB controller (not included). Ensure the 3-pin ARGB connector is properly connected to a 5V ARGB header.

6. Údržba

Regular maintenance helps ensure the longevity and performance of your liquid CPU cooler.

• Čištění prachu: Pravidelně čistěte prach z žeber chladiče a lopatek ventilátoru stlačeným vzduchem. Během čištění se ujistěte, že se ventilátory neotáčejí, aby nedošlo k jejich poškození.
• Zkontrolujte připojení: Occasionally check all cable connections (power, ARGB) to ensure they are secure.
• Kontrola trubek: Vizuálně zkontrolujte hadici, zda nevykazuje známky zlomení, netěsností nebo poškození.
• Teplovodní pasta: While not frequently required, if you remove the pump from the CPU, you must clean off old thermal paste and apply new thermal paste before re-mounting.

7. Řešení problémů

If you encounter issues with your ID-COOLING FX240 INF cooler, refer to the following common problems and solutions:

7.1 Vysoké teploty procesoru

• Check Pump Operation: Ensure the pump is receiving power and operating. Listen for a faint hum or feel for vibrations. Verify pump speed in BIOS/UEFI.
• Teplovodní pasta: Confirm thermal paste was applied correctly and evenly. Reapply if necessary.
• Montážní tlak: Ensure the pump is securely mounted to the CPU with adequate and even pressure.
• Provoz ventilátoru: Verify that both fans are spinning. Check fan connections and speeds in BIOS/UEFI.
• Průtok vzduchu do chladiče: Ensure the radiator fins are not clogged with dust and that case airflow is adequate.

7.2 Nadměrný hluk

• Hlučnost ventilátoru: Check if fan blades are obstructed or if screws are loose. Adjust fan speed curves in BIOS/UEFI to reduce noise at lower temperatures.
• Hlučnost čerpadla: A slight hum is normal. If a high-frequency whine is present, check pump speed settings in BIOS/UEFI. Some users report reducing pump speed slightly (e.g., to 63%) can mitigate whine without significant performance loss. Ensure the pump header is set to DC/Voltage control if it's a 3-pin connector.
• Vibrace: Ensure all components (fans, radiator, pump) are securely mounted to prevent vibration.

7.3 ARGB Lighting Not Working

• Zkontrolujte připojení: Verify the 3-pin ARGB connector is securely plugged into a 5V ARGB header on your motherboard.
• Ovládání softwaru: Ujistěte se, že je software RGB vaší základní desky správně nainstalován a nakonfigurován.
• Kompatibilita: Confirm you are using a 5V ARGB header, not a 12V RGB header.

8. Záruka a podpora

For warranty information and technical support, please refer to the official ID-COOLING webnebo se obraťte přímo na jejich zákaznický servis. Uschovejte si doklad o koupi pro případ reklamace.

Official ID-COOLING Store: ID-COOLING Amazon Store