Globo Lighting BOSTON Outdoor Pedestal Light

1. Úvod

Thank you for choosing the Globo Lighting BOSTON Outdoor Pedestal Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image 1.1: The BOSTON outdoor pedestal light providing illumination along a pathway.

2. Bezpečnostní pokyny

• Elektrická bezpečnost: Instalaci musí provést kvalifikovaný elektrikář v souladu se všemi místními a národními elektrotechnickými předpisy. Před instalací, údržbou nebo výměnou žárovky vždy odpojte hlavní jistič.
• Venkovní použití: This fixture is designed for outdoor use. Ensure all connections are waterproof and sealed appropriately to prevent water ingress.
• Typ žárovky: Use only E27 bulbs with the specified wattagE. Nepřekračujte maximální watttage vyznačeno na svítidle.
• Zacházení: S přístrojem zacházejte opatrně. Zabraňte jeho pádu nebo silným nárazům.
• Čištění: Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla. Čistěte měkkým,amp tkanina.
• Teplo: Před výměnou nechte žárovku zcela vychladnout.

3. Obsah balení

Před zahájením instalace zkontrolujte, zda jsou všechny komponenty přítomny a nepoškozené:

• 1x BOSTON Outdoor Pedestal Light Fixture (Model 105701)
• 1x montážní základna
• 1x Set of Mounting Hardware (screws, anchors)
• 1x Uživatelská příručka

Note: E27 bulb is not typically included and must be purchased separately.

4. Specifikace

5. Nastavení a instalace

Důležité: Ensure the main power supply is switched off at the circuit breaker before commencing installation.

1. Vyberte umístění: Select a suitable outdoor location for the pedestal light, ensuring it is on a stable, level surface and has access to the necessary electrical wiring.
2. Příprava zapojení: If not already present, run appropriate outdoor-rated electrical cable to the installation point. Consult a qualified electrician for this step.
3. Namontujte základnu: Position the mounting base on the desired surface. Mark the drilling points through the holes in the base. Drill pilot holes and secure the base using the provided mounting hardware (screws and anchors). Ensure the base is firmly attached.
4. Připojení elektrických vodičů: Carefully connect the electrical wires from your power supply to the terminals inside the fixture. Follow the standard wiring color codes (e.g., Live, Neutral, Earth). Ensure all connections are secure and properly insulated.
5. Instalace žárovky: Insert a suitable E27 bulb (not included) into the lamp držák. NEUTAHUJTE příliš silně.
6. Bezpečné upevnění: Attach the main body of the pedestal light to the mounted base, ensuring it is securely fastened and sealed against moisture.
7. Obnovit napájení: Jakmile je instalace dokončena a všechna připojení jsou bezpečná, obnovte napájení hlavním jističem.

Image 5.1: The pedestal light installed on a patio, demonstrating a typical mounting scenario.

6. Návod k obsluze

The BOSTON Pedestal Light features an integrated motion sensor for automatic operation.

• Zapnutí: Once installed and power is restored, the light will enter a warm-up period (typically a few seconds) before the motion sensor becomes active.
• Pohybový senzor: The integrated motion sensor detects movement within its detection range. When motion is detected, the light will illuminate.
• Automatické vypnutí: After a period of no detected motion, the light will automatically turn off. The duration of illumination is typically pre-set or adjustable via controls on the sensor (if available). Refer to the sensor's specific markings for adjustment options.
• Denní/noční senzor: The motion sensor also includes a photocell that prevents the light from activating during daylight hours, conserving energy. The light will only activate due to motion when ambient light levels are low enough.

Image 6.1: Detail of the motion sensor on the pedestal light, highlighting its detection area.

Image 6.2: The pedestal light operating at night, with the motion sensor detecting movement.

7. Údržba

• Čištění: Pravidelně čistěte přípravek měkkým, damp cloth to remove dirt and debris. Do not use harsh chemicals or abrasive materials, as these can damage the finish or plastic components.
• Výměna žárovky:
  1. Ensure the power supply to the fixture is turned off at the circuit breaker.
  2. Nechte starou žárovku zcela vychladnout, než se jí dotknete.
  3. Carefully unscrew the top cover or access panel to reach the E27 bulb.
  4. Unscrew the old bulb and replace it with a new E27 bulb of the correct wattage.
  5. Securely reattach the cover or access panel, ensuring a watertight seal.
  6. Obnovte napájení.
• Inspekce: Periodically inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly to ensure continued safe operation.

8. Řešení problémů

If you experience persistent issues not covered here, please contact a qualified electrician or the product supplier.

9. Záruka a podpora

This product is covered by the standard warranty provided by the manufacturer. Please retain your proof of purchase for any warranty claims. For technical support or further assistance, please contact your retailer or the Globo Lighting customer service department.

Contact information can typically be found on the product packaging or the manufacturer's official webmísto.