Fiamma Aluminium Wall Brackets for Awning Legs 98655-728

Zavedení

This manual provides instructions for the proper installation, operation, and maintenance of your Fiamma Aluminium Wall Brackets for Awning Legs, model 98655-728. These brackets are designed to securely hold the support legs of your Fiamma awning against the wall of your recreational vehicle or camper, offering stability and convenience.

Bezpečnostní informace

• Před instalací a použitím si pečlivě přečtěte všechny pokyny.
• Ujistěte se, že montážní povrch je čistý, suchý a konstrukčně pevný.
• Během instalace používejte vhodné nástroje a noste ochranné pomůcky.
• Do not exceed the maximum weight recommendation of 138 grams per bracket.
• Regularly inspect the brackets for signs of wear or damage. Replace immediately if any damage is found.

Obsah balení

Před zahájením instalace ověřte, zda jsou přítomny všechny komponenty.

Image: Components of the Fiamma Aluminium Wall Brackets kit, including two aluminum brackets, two black plastic base plates, two black plastic leg holders, four screws, and two metal shims.

• 2x Aluminium Wall Brackets
• 2x Black Plastic Base Plates
• 2x Black Plastic Leg Holders
• 4x montážní šrouby
• 2x Metal Shims (if included in your specific kit)

Nastavení a instalace

These brackets are designed for wall-mount installation on metal surfaces.

1. Vyberte umístění: Select a suitable, flat, and structurally sound area on your RV or camper wall where the awning legs will rest when retracted. Ensure the location allows for proper support and does not interfere with other components.
2. Čistý povrch: Thoroughly clean the mounting surface to remove any dirt, grease, or debris. A clean surface is essential for secure attachment.
3. Position Base Plate: Place one black plastic base plate against the cleaned wall at the desired mounting point. Mark the screw holes.
4. Vrtací pilotní otvory: Carefully drill pilot holes at the marked locations. Ensure the drill bit size is appropriate for the provided screws to prevent stripping or cracking the mounting surface.
5. Připevněte základní desku: Secure the black plastic base plate to the wall using two mounting screws. It is recommended to apply a suitable sealant (e.g., silicone) around the screw holes and under the base plate to prevent water ingress.
6. Install Aluminium Bracket: Slide the aluminium wall bracket onto the attached black plastic base plate. Ensure it clicks securely into place.
7. Repeat for Second Bracket: Follow steps 3-6 to install the second bracket at the appropriate distance for your awning leg.
8. Test stability: Once both brackets are installed, gently test their stability. Ensure they are firmly attached to the wall.

Obrázek: Detail view of the Fiamma Aluminium Wall Brackets and associated hardware, showing the individual pieces before assembly.

Návod k obsluze

To use the Fiamma Aluminium Wall Brackets with your awning legs:

1. Extend Awning Legs: Extend your awning legs as per your awning's instructions.
2. Position Legs: Guide the bottom end of each awning leg into the corresponding aluminium wall bracket.
3. Bezpečné nohy: Ensure the awning legs are fully seated and secured within the brackets. The design of the bracket is intended to hold the leg firmly.
4. Zatahovací markýza: When retracting your awning, carefully remove the legs from the wall brackets before fully stowing the awning.

Údržba

• Čištění: Clean the brackets periodically with mild soap and water. Avoid abrasive cleaners that could damage the aluminum finish.
• Inspekce: Regularly inspect the brackets and mounting screws for any signs of loosening, corrosion, or damage. Tighten screws if necessary.
• Kontrola tmelu: Periodically check the sealant around the mounting points for cracks or deterioration. Reapply sealant as needed to maintain a watertight seal.

Odstraňování problémů

Bracket Not Sticking/Loosening

If a bracket does not adhere properly or loosens over time:

• Re-clean Surface: Ensure the mounting surface was thoroughly cleaned and free of contaminants before installation.
• Kontrolní šrouby: Verify that the mounting screws are tightened securely. Do not overtighten.
• Znovu naneste tmel: If the issue is related to the seal, remove the bracket, clean the area, and reapply a fresh, high-quality sealant before re-mounting.
• Kontrola poškození: Check the bracket and the wall for any damage that might prevent a secure fit.

Specifikace

• Model: 98655-728
• Materiál: Hliník
• Typ dokončení: Silber (Silver)
• Typ montáže: Držák na zeď
• Hmotnost položky: Přibližně 0.18 kilogramu (6.3 unce)
• Rozměry produktu (D x Š x V): 3.82 x 4.37 x 1.42 palce
• Maximální hmotnost Doporučení: 138 Grams (per bracket)
• Doporučení pro povrch: Kov
• Počet háčků: 2 (referring to the set of two brackets)

Záruka a podpora

For warranty information or technical support, please refer to the official Fiamma website or contact your authorized Fiamma dealer. Keep your purchase receipt as proof of purchase.