Foster 54" Commercial Freezer Instruction Manual

1.1 Bezpečnostní opatření

• Před čištěním nebo servisem jednotky vždy odpojte napájení.
• Zajistěte správné uzemnění, abyste zabránili úrazu elektrickým proudem.
• V tomto spotřebiči neskladujte výbušné látky, jako jsou aerosolové plechovky s hořlavou hnací látkou.
• Maintain adequate ventilation around the unit to ensure efficient operation and prevent overheating.
• Udržujte všechny ventilační otvory volné.
• Nepoškozujte chladicí okruh.
• Opravy by měl provádět pouze kvalifikovaný personál.

2.1 Vlastnosti

• Powerful Freezing Capacity: Robust compressor system and fan cooling mechanism ensure reliable freezing performance within -8°F to 0°F.
• Efficient Temperature Control: Dixell temperature control allows precise adjustments for optimal preservation of frozen goods.
• Prostorné úložné řešení: Generous 39.4 cubic feet capacity with two solid doors, ideal for high-volume establishments.
• Odolná konstrukce: Built with stainless steel both inside and out for longevity and durability in demanding commercial environments.
• svtage: Pracuje na 115 voltech.
• Wattage: 955 wattů.
• Osvědčení: ETL certified for safety and sanitation.

3.1 Vybalení

Carefully remove all packaging materials. Inspect the freezer for any shipping damage. Report any damage immediately to the carrier and your supplier. Do not discard packaging until the unit has been tested and is operating correctly.

3.2 Umístění

• Place the freezer on a strong, level surface capable of supporting its weight when fully loaded.
• Ensure adequate air circulation around the unit. Maintain a minimum of 6 inches (15 cm) clearance from walls and other equipment for proper ventilation.
• Avoid direct sunlight or proximity to heat-generating appliances (ovens, stoves) to ensure optimal performance and energy efficiency.
• The ambient temperature should not exceed 90°F (32°C).

3.3 Elektrické připojení

• The freezer requires a dedicated 115V, 60Hz, single-phase electrical outlet.
• Ujistěte se, že elektrické napájení odpovídá požadavkům uvedeným na typovém štítku jednotky.
• Nepoužívejte prodlužovací kabely nebo adaptéry.
• Jednotka musí být řádně uzemněna.

3.4 První spuštění

• After positioning the unit, allow it to stand upright for at least 2 hours before plugging it in. This allows the refrigerant to settle.
• Zapojte jednotku do určené elektrické zásuvky.
• The freezer will begin to cool. Allow 24 hours for the unit to reach its set temperature before loading with products.

4.1 Temperature Control (Dixell Controller)

Your Foster freezer is equipped with a Dixell digital temperature controller, allowing precise temperature management. The factory preset temperature range is -8°F to 0°F (-22°C to -18°C).

• Viewing the Setpoint: Press and immediately release the SET button. The display will show the setpoint value. Press SET again or wait 5 seconds to return to the normal display.
• Changing the Setpoint:
  1. Press the SET button for more than 2 seconds. The setpoint value will flash.
  2. Use the UP or DOWN arrows to adjust the temperature.
  3. Press SET again to confirm the new value.
• Ruční odmrazování: To initiate a manual defrost cycle, press and hold the defrost button (usually a snowflake icon) for approximately 5 seconds.

Note: Refer to the specific Dixell controller model manual for advanced programming and alarm settings.

4.2 Vkládání do mrazničky

• Nepřetěžujte mrazničku. Pro efektivní chlazení nechte kolem produktů dostatek prostoru pro cirkulaci vzduchu.
• Ensure doors are closed completely after each use to maintain temperature and prevent ice buildup.
• Organize products to minimize door opening times.

5.1 Čištění

• Interiér: Clean the interior regularly with a mild soap and warm water solution. Rinse thoroughly and dry completely to prevent odors and mildew. Do not use abrasive cleaners or steel wool.
• Vnější: Wipe down the stainless steel exterior with a soft cloth and a non-abrasive stainless steel cleaner. Always wipe in the direction of the grain.
• Těsnění dveří: Clean door gaskets regularly with warm water and mild soap. Ensure they are pliable and seal properly. Replace worn or damaged gaskets promptly.
• Kondenzátorová cívka: The condenser coil should be cleaned every 30 days or as needed. Disconnect power before cleaning. Use a stiff brush or vacuum cleaner to remove dust and debris from the coil. A dirty condenser coil can significantly reduce efficiency and increase energy consumption.

5.2 Odmrazování

This unit features an automatic defrost system. However, if excessive ice buildup occurs, a manual defrost may be necessary. Refer to Section 4.1 for manual defrost initiation.