Zavedení
Welcome and thank you for choosing the Baseus UltraControl Go Series Car Holder. This manual provides instructions for proper installation, operation, and maintenance of your device. Please read it carefully before use to ensure optimal performance and safety.
Konec produktuview
Komponenty produktu
The Baseus UltraControl Go Series Car Holder consists of the following main components:
- Telefon Clamp: Bezpečně drží váš smartphone.
- Nastavitelné rameno: Allows for positioning the phone at various angles.
- Základna přísavky: Provides secure attachment to surfaces.
- Uvolňovací tlačítko: For easy one-hand operation to release the clamp zbraně.
Obrázek: Přední strana view of the Baseus UltraControl Go Series Car Holder, showing the phone clamp, adjustable arm, and suction cup base.
Nastavení a instalace
Výběr místa instalace
The Baseus UltraControl Go Series Car Holder can be installed on various smooth, flat surfaces within your vehicle, such as the dashboard or windshield. Ensure the chosen location does not obstruct your view nebo zasahovat do ovládání vozidla.
Obrázek: Přamples of suitable installation locations for the car holder, including the dashboard, passenger seat area, and windshield.
Attaching the Suction Cup Base
- Clean the desired surface thoroughly to remove dust and grease.
- Place the suction cup base firmly onto the clean surface.
- Press down on the locking lever (if present) on the suction cup to create a vacuum seal.
Poznámka: The suction cup features removable nano adhesive for enhanced grip. Ensure the surface is suitable for adhesive application if using this feature.
Návod k obsluze
Inserting Your Phone
- Gently pull open the clamping arms of the holder.
- Place your smartphone into the holder, ensuring it rests securely on the bottom support.
- Uvolněte třamping arms. The damped design will automatically adjust to securely grip your phone.
The holder is compatible with phones ranging from 5.4 to 7.2 inches.
Image: A smartphone held securely by the clamping arms of the car holder, illustrating the tight grip.
Removing Your Phone (Single-Hand Operation)
To remove your phone, press the release button located on the back of the holder's panel. The clamp arms will open, allowing you to easily retrieve your device.
Image: A hand pressing the release button on the back of the phone holder, demonstrating the single-hand operation for phone removal.
Úprava Viewúhel
The adjustable arm and ball joint allow for flexible positioning. Loosen the adjustment knob (if present) to change the angle, then tighten it to secure the desired position.
Péče a údržba
- Čištění: Otřete držák měkkým hadříkemamp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla.
- Přísavka: Pokud přísavka ztratí přilnavost, opláchněte ji teplou vodou a nechte ji uschnout na vzduchu. Tím se může obnovit její lepivost.
- Teplota: Avoid prolonged exposure to extreme temperatures, which can affect the material and adhesive properties.
- Silikonové podložky: The protective silicone pads on the clamping arms should be kept clean to maintain grip and prevent scratches to your phone.
Image: Illustration highlighting the meticulous craftsmanship and meshing gears designed to prevent squeaking during driving, indicating durability and quality.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Držák se nelepí na povrch. | Surface is dirty, uneven, or suction cup is not properly sealed. | Clean the surface. Ensure the suction cup lever is locked. Rinse and air dry the suction cup. |
| Telefon není bezpečně uchycen. | Phone size is outside the compatible range (5.4-7.2 inches) or clamping arms are obstructed. | Verify phone size. Ensure no obstructions prevent the arms from closing fully. |
| Holder makes noise during driving. | Loose connection or component. | Check all adjustable parts and ensure they are tightened. The design is intended to prevent squeaking. |
Specifikace produktu
- Číslo modelu: BS-CM025 (C40361600111-00)
- Značka: Baseus
- Applicable Phone Size: 5.4 - 7.2 palce
- Materiál: Silicone (for protective pads)
- Typ montáže: Vehicle Mount (Suction Cup)
- Speciální vlastnosti: Adjustable, Secure Clamping, Wide Compatibility, Secure Installation, Protective Silicone Pads, Single-Hand Operation
- Rozměry produktu: 18 x 0.5 x 10 cm
- Hmotnost položky: 120 g
- Barva: Černý
Image: Diagram highlighting key features such as damping třamp arms, vacuum suction cup, removable nano adhesive, and easy operation.
Záruka a zákaznická podpora
Informace o záruce nebo technickou podporu získáte od oficiálního prodejce Baseus. webnebo se obraťte na místního distributora. Uschovejte si doklad o koupi pro případ reklamace.
Výrobce: Baseus
Webmísto: www.baseus.com
Kontakt: Viz webstránky s regionálními kontaktními informacemi.
