Weytoll 5000W Battery Spot Welder Instruction Manual

Zavedení

This manual provides detailed instructions for the safe and effective operation, setup, and maintenance of your Weytoll 5000W Battery Spot Welder. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage or injury.

Bezpečnostní informace

Always prioritize safety when operating electrical equipment. Failure to follow safety guidelines can result in electric shock, fire, or serious injury.

• Ensure the work area is clean, dry, and well-ventilated.
• Používejte vhodné osobní ochranné prostředky (OOP), včetně ochranných brýlí a rukavic.
• Nepoužívejte bodovou svářečku vamp nebo vlhké podmínky.
• Udržujte děti a neoprávněné osoby mimo provozní prostor.
• Před prováděním jakékoli údržby nebo seřizování odpojte napájení.
• Do not attempt to weld materials other than those specified (nickel sheets for battery packs).
• Avoid touching the welding pens or welded material immediately after operation, as they may be hot.
• Use only the provided charger and ensure it is connected correctly.
• Inspect the device and cables for any damage before each use. Do not use if damaged.

Obsah balení

Po vybalení zkontrolujte, zda jsou všechny níže uvedené položky přítomny a nepoškozené:

• Weytoll 5000W Battery Spot Welder Unit
• Spot Welding Pens (with copper cables)
• Nožní spínač
• Napájecí adaptér/nabíječka
• Niklové proužky (sample roll)
• Uživatelská příručka (tento dokument)

Obrázek 1: Weytoll 5000W Battery Spot Welder with all components, including the main unit, welding pens, foot pedal, charger, and nickel strips.

Konec produktuview

The Weytoll 5000W Battery Spot Welder is designed for efficient spot welding of 0.1mm to 0.15mm nickel sheets onto various battery types, including 18650, 26650, and 32650 cells. It features a compact design, adjustable output power, and a digital display for monitoring battery voltage.

Obrázek 2: Front panel of the spot welder, highlighting the power adjustment knob, LED indicator, digital display for battery voltage, spot welding pen interfaces, foot pedal interface, and charging interface.

Obrázek 3: The power adjustment knob allows fine-tuning of the output current. A higher setting corresponds to a higher output power.

Obrázek 4: The detachable spot welding pens feature copper tips for efficient current transfer. These can be disassembled and replaced if necessary.

Nastavení

1. Nabijte zařízení: Before initial use, fully charge the spot welder using the provided power adapter. Connect the adapter to the charging interface on the unit and plug it into a suitable power outlet. The indicator light on the charger will change (e.g., from red to green) when charging is complete. Ensure the battery voltage displayed on the unit is above 7.3V for optimal performance.
2. Připojte svařovací pera: Insert the connectors of the spot welding pens into the designated interfaces on the front panel of the spot welder. Ensure a secure connection.
3. Připojení nožního pedálu: Plug the foot pedal switch into the foot interface on the front panel.
4. Připravte pracovní plochu: Place the spot welder on a stable, non-conductive surface. Ensure adequate lighting and ventilation.

Návod k obsluze

1. Zapnutí: Turn the power knob clockwise to power on the device. The LED indicator will light up, and the digital display will show the current battery voltage.
2. Adjust Output Power: Rotate the power adjustment knob to select the desired output power level (1-10 gears). Start with a lower setting (e.g., 5-7) and test on a scrap piece of nickel strip to determine the optimal setting for your specific material thickness and battery type. Higher numbers indicate higher output power.
3. Připravte si materiály: Ensure the nickel sheet and battery terminals are clean and free of oxidation. Place the nickel sheet firmly onto the battery terminal where the weld is to be made.
4. Perform Spot Weld:
   • Hold the two welding pens firmly, ensuring the tips are clean and sharp.
   • Place the tips of the two welding pens onto the nickel sheet, directly over the desired welding point. Apply firm, even pressure.
   • Press and hold the foot pedal switch. The red indicator light on the unit will flash quickly three times.
   • After the third flash, the current will be output, and the welding process will be completed. Release the foot pedal.
5. Kontrola svaru: Carefully inspect the welded joint. A good weld should be firm and not easily pulled apart. Adjust the power setting if the weld is too weak or too strong.
6. Vypnout: After use, turn the power knob counter-clockwise to power off the device.

Obrázek 5: Illustration of the spot welding process, showing the placement of welding pens on a nickel sheet over battery cells and the use of the foot pedal.

Obrázek 6: Examples of spot welding results, demonstrating easy application, firm welds, complete solder joints, and lithium battery nickel sheet welding.

Údržba

• Čištění: Regularly clean the welding pen tips with fine-grit sandpaper or a wire brush to remove any residue and ensure good electrical contact. Wipe the main unit with a dry, soft cloth. Do not use abrasive cleaners or solvents.
• Skladování: Store the spot welder and its accessories in a dry, cool place, away from direct sunlight and moisture.
• Péče o baterie: If the device will not be used for an extended period, charge it periodically to maintain battery health. Avoid fully discharging the battery for prolonged periods.
• Kontrola kabelů: Periodically check all cables and connections for signs of wear, cuts, or damage. Replace any damaged components immediately.

Odstraňování problémů

Specifikace

• Model: YOX1896218093033NK
• Značka: Weytoll
• Výstupní výkon: 5000W (špička)
• Nastavení výstupního výkonu: 10 ozubená kola
• Spot Welding Thickness: 0.1mm - 0.15mm (Nickel Sheet)
• Kompatibilní baterie: 18650, 26650, 32650, and similar cylindrical batteries
• Typ baterie: Lithium Ion (součástí balení)
• Hmotnost položky: 1.96 libry (přibližně 0.89 kg)
• Rozměry produktu: 5.31 x 4.13 x 7.68 palců (přibližně 13.5 x 10.5 x 19.5 cm)
• Výrobce: Weytoll

Záruka a podpora

For any product-related inquiries, technical assistance, or warranty claims, please contact Weytoll customer support. Refer to your purchase documentation for specific warranty terms and contact information. The manufacturer is committed to providing support for product issues.

You can often find support contact details on the official Weytoll webwebu nebo prostřednictvím prodejce, u kterého byl produkt zakoupen.