ID-COOLING IS-55 Black Low Profile Návod k použití chladiče CPU

Zavedení

The ID-COOLING IS-55 Black is a low-profile CPU air cooler designed for efficient heat dissipation in compact systems. Featuring 5 heatpipes and a 120mm PWM fan, it offers effective cooling performance while maintaining a low 57mm total height, making it suitable for HTPCs, ITX, and Small Form Factor (SFF) builds. This manual provides essential information for proper installation, operation, and maintenance of your IS-55 CPU cooler.

Co je v krabici

Před zahájením instalace se prosím ujistěte, že jsou všechny komponenty přítomny:

• IS-55 Heatsink with pre-attached 120mm PWM Fan
• Intel Mounting Brackets (LGA1851/1700/1200/115X)
• Montážní držáky AMD (AM4/AM5)
• Backplate (for Intel sockets)
• Montážní šrouby a podložky
• Termální pasta
• Klíč/nástroj

Image: All components included in the ID-COOLING IS-55 Black CPU Cooler package.

Specifikace

Image: Fan dimensions for the IS-55 cooler.

Kompatibilita

The ID-COOLING IS-55 CPU Cooler is compatible with a wide range of Intel and AMD CPU sockets:

• Patice Intel: LGA1851, LGA1700, LGA1200, LGA1151, LGA1150, LGA1155, LGA1156
• Patice AMD: AM5, AM4

Its low-profile design ensures excellent RAM compatibility, even on Mini-ITX motherboards. It offers 100% clearance for I/O and up to 33mm RAM height. For low-profile I/O, the cooler can be rotated 180 degrees to support higher RAM modules.

Image: RAM and I/O compatibility diagram.

Nastavení a instalace

Before installation, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific CPU socket details.

Obecné kroky instalace:

1. Příprava CPU a základní desky: Clean the CPU surface thoroughly. If replacing an old cooler, remove any existing thermal paste.
2. Naneste termální pastu: Apply a small, pea-sized amount of thermal paste to the center of the CPU's Integrated Heat Spreader (IHS). Do not spread it manually; the pressure from the cooler will distribute it.
3. Připevnění montážního materiálu: Follow the specific instructions below for your CPU socket type (Intel or AMD) to attach the correct backplate and mounting brackets to your motherboard.
4. Mount the Cooler: Carefully place the IS-55 heatsink onto the CPU, aligning the mounting holes. Secure it with the provided screws, tightening them in a diagonal pattern until snug. Do not overtighten.
5. Připojení kabelu ventilátoru: Connect the 4-pin PWM fan cable from the IS-55 cooler to the CPU_FAN header on your motherboard.

Intel LGA1851/1700/1200/115X Installation:

1. Install the universal Intel backplate behind the motherboard, aligning the holes with the CPU socket.
2. Place the appropriate Intel mounting standoffs through the motherboard holes and into the backplate.
3. Secure the Intel mounting brackets onto the standoffs using the provided nuts.
4. Proceed with steps 4 and 5 from the General Installation Steps.

AMD AM4/AM5 Installation:

1. Remove the stock plastic retention modules from the motherboard, but keep the original AMD backplate.
2. Install the AMD mounting standoffs into the holes around the CPU socket, screwing them into the original AMD backplate.
3. Secure the AMD mounting brackets onto the standoffs using the provided nuts.
4. Proceed with steps 4 and 5 from the General Installation Steps.

Image: IS-55 cooler installed in a small form factor PC case.

Návod k obsluze

The ID-COOLING IS-55 features a PWM (Pulse Width Modulation) controlled fan. This allows your motherboard to automatically adjust the fan speed based on CPU temperature, optimizing for both cooling performance and noise levels.

• Automatické ovládání: For most users, the default fan control settings in your motherboard's BIOS/UEFI are sufficient. The fan will spin faster under heavy CPU load and slow down during idle periods.
• Manual Adjustment (Advanced Users): You can fine-tune fan curves in your motherboard's BIOS/UEFI settings or using third-party software (if supported by your motherboard) to achieve a preferred balance between cooling and acoustics.

Image: PWM fan control diagram.

Údržba

Pravidelná údržba pomáhá zajistit optimální výkon a dlouhou životnost chladiče procesoru.

• Odstranění prachu: Periodically (e.g., every 3-6 months), use compressed air to blow dust out of the heatsink fins and fan blades. Ensure the fan is held stationary during cleaning to prevent damage to the bearings.
• Čištění ventilátoru: If dust buildup is significant, gently wipe the fan blades with a soft, dry cloth.
• Teplovodní pasta: While not typically required frequently, if you remove the cooler for any reason, it is recommended to clean off old thermal paste from both the CPU and cooler base and apply fresh thermal paste before reinstallation.

Image: Black coated heatsink fins and heatpipes.

Odstraňování problémů

If you encounter issues with your ID-COOLING IS-55 CPU Cooler, consider the following common solutions:

• Vysoké teploty procesoru:
  • Ensure the cooler is securely mounted and making full contact with the CPU.
  • Zkontrolujte, zda byla teplovodivá pasta nanesena správně a rovnoměrně.
  • Zkontrolujte, zda se ventilátor otáčí. Pokud ne, ujistěte se, že je správně připojen k konektoru CPU_FAN.
  • Clean any dust buildup from the heatsink fins and fan.
  • Check BIOS/UEFI settings to ensure fan speed control is enabled and functioning correctly.
• Nadměrný hluk ventilátoru:
  • Zkontrolujte, zda do lopatek ventilátoru nenarážejí nějaké kabely nebo překážky.
  • Clean the fan blades and heatsink for dust.
  • Adjust fan curve settings in BIOS/UEFI to reduce maximum fan speed if temperatures allow.
• Ventilátor se netočí:
  • Ensure the 4-pin PWM cable is firmly connected to the CPU_FAN header on the motherboard.
  • Check BIOS/UEFI settings to ensure the CPU_FAN header is enabled and not set to a very low RPM threshold that prevents it from spinning at idle.
  • Test the fan on another fan header if available to rule out a faulty fan or motherboard header.

Záruka a podpora

ID-COOLING products typically come with a manufacturer's warranty. Please refer to the official ID-COOLING website or your retailer for specific warranty terms and conditions applicable to your region and purchase date.

For technical support, troubleshooting assistance, or warranty claims, please contact ID-COOLING customer service through their official webwebu nebo kontaktních informací uvedených na obalu produktu.

Oficiální Webmísto: www.idcooling.com