1. Úvod
This instruction manual provides essential information for the proper installation, operation, and maintenance of your new Artist Unknown 3&4 Hole Stainless Steel Steam Wand Tip. This product is designed to enhance the milk frothing capabilities of compatible Breville 8 Series Espresso Machines. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.
2. Bezpečnostní informace
- Always ensure the espresso machine is turned off and cooled down before attempting installation or removal of the steam wand tip.
- Exercise caution when handling the steam wand tip, as it may become hot during operation.
- Uchovávejte mimo dosah dětí.
- Use only as intended for espresso machine steam wands.
- Inspect the tip for any damage before each use. Do not use if damaged.
3. Obsah balení
Ověřte, zda jsou v balení přítomny všechny položky:
- 1 x Stainless Steel Steam Wand Tip (3-hole or 4-hole variant, as purchased)
4. Specifikace
| Funkce | Detail |
|---|---|
| Materiál | Nerezová ocel 304 potravinářské kvality |
| Průměr otvoru | 1 mm |
| Velikost (přibližně) | 23 x 12.98 mm / 0.9 x 0.5 palce |
| Kompatibilita | Breville 8 Series Espresso Machines |
| Konfigurace otvoru | 3-Hole or 4-Hole (depending on variant) |
Note: Dimensions are approximate and may vary slightly due to manufacturing tolerances.
Image: Detailed dimensions of the 3-hole and 4-hole steam wand tips, showing height, width, and bore diameter.
5. Instalace
Follow these steps to replace your existing steam wand tip:
- Ensure your Breville 8 Series Espresso Machine is powered off and unplugged. Allow the steam wand to cool completely.
- Carefully unscrew the original steam wand tip from the steam wand. You may need a cloth for grip.
- Clean any residue from the steam wand's threads.
- Screw the new Artist Unknown steam wand tip onto the steam wand. Hand-tighten until secure, but do not overtighten.
- Ensure the tip is firmly attached and there are no gaps.
Image: A hand demonstrating the attachment point of the steam wand tip to the espresso machine's steam arm.
6. Operation (Milk Frothing)
The multi-hole design of this steam wand tip is intended to provide a more even steam distribution for milk frothing. Achieving fine milk foam requires practice and attention to technique, milk concentration, and steam temperature.
- Připravte mléko: Pour cold milk into a frothing pitcher. Fill to just below the spout.
- Proplachovací parní tryska: Krátce otevřete parní ventil, abyste z trysky vypustili kondenzovanou vodu. Zavřete ventil.
- Poloha hůlky: Insert the steam wand tip into the milk, just below the surface, at an angle. The tip should be submerged about 1 cm.
- Začněte vařit v páře: Open the steam valve fully. Listen for a gentle 'tearing paper' sound, indicating you are incorporating air. Maintain this position for a few seconds to create microfoam.
- Submerge and Heat: Once enough air is incorporated (milk volume increases slightly), lower the pitcher slightly to fully submerge the tip. This heats the milk and integrates the foam. Keep the milk circulating in a vortex.
- Monitorovat teplotu: Continue heating until the pitcher is too hot to comfortably touch (approximately 140-150°F or 60-65°C).
- Dokončit: Close the steam valve, then immediately remove the pitcher. Wipe the steam wand clean with a damp tkanina.
Image: A visual guide illustrating the six steps of milk frothing, from pouring milk to coffee extraction.
Image: A close-up of a steam wand tip submerged in milk within a frothing pitcher, actively creating foam.
7. Údržba a čištění
Regular cleaning is crucial for hygiene and to prevent blockages in the steam wand tip.
- Po každém použití: Immediately after frothing, wipe the steam wand and tip with a clean, damp cloth to remove any milk residue. Briefly purge the steam wand again to clear any milk from the internal holes.
- Denní úklid: If milk dries on the tip, unscrew it from the wand and soak it in warm, soapy water. Use a small brush or needle to clear any blocked holes. Rinse thoroughly.
- Hloubkové čištění (týdně/každé dva týdny): For stubborn blockages, soak the tip in a solution of espresso machine cleaner or white vinegar and water. Follow the cleaner's instructions for dilution and soaking time. Rinse thoroughly before reattaching.
8. Řešení problémů
If you encounter issues with your steam wand tip, refer to the following common problems and solutions:
| Problém | Řešení |
|---|---|
| Weak or inconsistent steam flow | Check for blockages in the tip holes. Perform a deep clean. Ensure the tip is securely attached. Verify your espresso machine's steam pressure is adequate. |
| Poor milk foam quality (too bubbly or flat) | Review operation steps, focusing on wand positioning and air incorporation. Ensure milk is fresh and cold. Practice technique. |
| Tip does not fit the steam wand | Confirm your espresso machine is a Breville 8 Series model. Check the threading on both the wand and the tip for damage. |
9. Záruka a podpora
This product is provided as a replacement part. For specific warranty information, please refer to the terms and conditions provided by your retailer at the time of purchase. For technical support or further assistance, please contact the seller directly through the platform where the purchase was made.
