Behringer TD-3-MO-AM Uživatelská příručka k analogovému basovému linkovému syntezátoru

Rozložení předního panelu

Below is an image illustrating the front panel controls and connections of the TD-3-MO-AM synthesizer. Familiarize yourself with these components before operation.

Obrázek 1: Front panel of the Behringer TD-3-MO-AM Analog Bass Line Synthesizer. This image displays all knobs, buttons, and input/output jacks, including controls for Tune, Cutoff, Resonance, Envelope, Decay, Accent, Tempo, Wave, Track/Pattern Group, Mode, Gate, Slide Time, Sweep Speed, Filter FM, Volume, and various input/output ports.

2.1 Vybalení a kontrola

Carefully remove the synthesizer from its packaging. Inspect the unit for any signs of damage during transit. Retain the original packaging for future transport or storage.

2.2 Připojení napájení

Connect the provided power adapter to the DC IN port on the rear panel of the TD-3-MO-AM. Plug the adapter into a suitable power outlet. Ensure the power switch is in the OFF position before connecting power.

2.3 Audio výstup

Connect the AUDIO OUT jack (typically a 1/4" TS or TRS jack, though not explicitly listed in specs, common for synths) on the rear panel to your mixer, audio interface, or amplifier using a standard audio cable. For headphone monitoring, use the PHONES output.

2.4 MIDI a USB připojení

The TD-3-MO-AM supports MIDI and USB connectivity for integration with other musical equipment or a computer.

• MIDI VSTUP/VÝSTUP: Use standard 5-pin DIN MIDI cables to connect to other MIDI devices for sequencing or control.
• USB: Connect the USB-A port (as per specifications) to your computer for MIDI over USB and firmware updates.

2.5 CV/Gate Connections

The synthesizer features various CV (Control Voltage) and Gate inputs/outputs for integration with modular synthesizers and other analog gear.

• ACCENT IN, SLIDE IN, GATE IN, CV IN: These inputs allow external control over corresponding parameters.
• SYNC IN, ACCENT OUT, GATE OUT, CV OUT, FILTER OUT: These outputs provide control signals to other devices.

3.1 Zapnutí/vypnutí

To power on, ensure all connections are secure, then flip the power switch to the ON position. To power off, flip the switch to the OFF position and disconnect the power adapter.

3.2 Sound Generation Basics

The TD-3-MO-AM generates sound using an analog oscillator. Adjust the NALADIT, ODSTRANIT, REZONANCE, OBÁLKA, ROZKLADa PŘÍZVUK knobs to shape the sound. The VLNA switch selects between sawtooth and square waveforms.

3.3 Obsluha sekvenceru

The built-in 16-step sequencer allows for programming bass lines. Use the MODE switch to select between WRITE and PLAY modes. In WRITE mode, you can input notes and parameters for each step. In PLAY mode, the sequencer will playback the programmed pattern.

• NAPSAT: For creating and editing patterns.
• HRÁT SI: For playing back patterns.
• TRK/PATT: Selects between Track and Pattern modes for sequencing.

Upravte TEMPO knob to control the playback speed of the sequencer.

3.4 Arpeggiator

The arpeggiator can generate rhythmic patterns from held notes. Refer to the detailed manual for specific arpeggiator modes and controls.

3.5 Filter and Overdrive

The 4-pole resonant lowpass filter is a key component of the TD-3-MO-AM's sound. Use the ODSTRANIT a REZONANCE knobs to sculpt the tone. The PŘEVODOVKA control adds distortion and grit to the sound.

4.1 Čištění

To clean the unit, use a soft, dry cloth. Do not use abrasive cleaners, waxes, or solvents. Avoid spraying liquids directly onto the unit.

4.2 Skladování

When not in use for extended periods, store the synthesizer in a cool, dry place, away from direct sunlight and extreme temperatures. It is recommended to use the original packaging for storage.

4.3 aktualizací firmwaru

Pravidelně kontrolujte Behringer website for firmware updates. Updates can provide new features, bug fixes, and performance improvements. Follow the instructions provided with the firmware update package carefully.

5.1 Žádný zvukový výstup

• Ujistěte se, že je napájecí adaptér bezpečně připojen a že je zařízení zapnuté.
• Check all audio cable connections from the TD-3-MO-AM to your mixer/interface/ampživější.
• Verify that the VOLUME knob on the TD-3-MO-AM is turned up.
• Confirm that your mixer/interface/amplifier is powered on and its input levels are correctly set.
• If using headphones, ensure they are properly plugged into the PHONES jack and the volume is adequate.

5.2 Sekvencer nehraje

• Zajistěte MODE switch is set to PLAY.
• Verify that a pattern has been programmed and is selected.
• Zkontrolujte TEMPO knob; it might be set too low.
• If syncing externally, ensure the SYNC IN connection is active and receiving a valid clock signal.

5.3 MIDI/USB Connectivity Issues

• Ensure correct MIDI cable connections (MIDI OUT to MIDI IN, MIDI IN to MIDI OUT).
• For USB, verify the USB cable is securely connected to both the synthesizer and your computer.
• Check your computer's device manager or audio/MIDI settings to confirm the TD-3-MO-AM is recognized.
• Install any necessary drivers if prompted by your operating system (usually class-compliant, but check Behringer support).

7.1 Záruka na produkt

Behringer products typically come with a limited warranty covering manufacturing defects. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Behringer webUschovejte si doklad o koupi pro případ reklamace.

7.2 Zákaznická podpora

Pro technickou pomoc, řešení problémů nad rámec této příručky nebo servisní dotazy se obraťte na zákaznickou podporu Behringer. Kontaktní informace a další zdroje naleznete na oficiálních webových stránkách Behringer. webmísto: www.behringer.com.

For protection plans, refer to the options available at the point of purchase, such as those offered by Amazon:

• Dvouletý ochranný plán
• Dvouletý ochranný plán
• Kompletní ochrana (měsíční tarif)