1. Úvod
This manual provides comprehensive instructions for the installation, setup, operation, and maintenance of your LoraTap Wireless Switch Kit, Model SS9111Q1. This kit allows for convenient remote control of lighting fixtures using an 868 MHz radio frequency transmitter and a compact receiver module. It is designed for easy integration into existing electrical systems, offering both fixed and portable control options.
Před instalací a použitím si prosím pečlivě přečtěte tento návod k obsluze, abyste zajistili bezpečný a správný provoz.
2. Bezpečnostní informace
VAROVÁNÍ: Electrical installation should only be performed by a qualified electrician or competent person. Always disconnect power at the circuit breaker before performing any electrical work.
- Před instalací nebo údržbou se ujistěte, že je hlavní napájení vypnuto.
- The receiver module requires a neutral wire for operation. Verify its availability before installation.
- Do not use this switch with dimmer switches or any other power variation wall switches, as this may damage the relay receiver.
- The maximum load capacity is 2500W. Do not exceed this rating.
- Provozní objemtage range: 85-265V AC.
- This product is not a Wi-Fi switch.
Image: Illustration showing incompatible dimmer switches with a red cross, indicating they should not be used with the LoraTap wireless switch kit.
3. Obsah balení
Ověřte, zda jsou v balení přítomny všechny komponenty:
- 1x Wireless Transmitter (Remote Control)
- 1x Relay Receiver Module
- 1x Wall Plate for Transmitter
- 3x Double-sided Adhesive Tapes
- Šrouby a nástěnné kotvy
- 1x Small Screwdriver
- 3x Wiring Cables
- 1x User Guide (This manual)
Image: Visual representation of the LoraTap Wireless Switch Kit contents, including the transmitter, receiver, mounting accessories, and tools.
4. Specifikace
| Funkce | Detail |
|---|---|
| Číslo modelu | SS9111Q1 |
| Značka | Lora Tap |
| Provozní svtage | 85-265V AC |
| Maximální zátěžový výkon | 2500W |
| Rádiová frekvence | 868 MHz |
| Indoor Control Range | Up to 30 meters (through walls) |
| Outdoor Control Range | Až 200 metrů |
| Baterie vysílače | 1x CR2032 Lithium Metal (included) |
| Životnost baterie vysílače | Over 10 years (approx. 220,000 clicks) |
| Rozměry přijímače | Přibližně 46 mm x 46 mm x 18 mm (D x Š x V) |
| Rozměry vysílače | Approx. 67mm x 67mm (L x W) |
| Materiál | Plast |
| Certifikace | CE, RoHS |
Image: Dimensions of the wireless transmitter and its wall plate, highlighting the CR2032 battery.
5. Instalace
The LoraTap Wireless Switch Kit is designed for easy installation without extensive wiring or wall damage. Ensure power is disconnected before proceeding.
5.1 Receiver Module Wiring
The receiver module must be installed in a location where it can receive power (Live and Neutral) and connect to the load (e.g., a light fixture). A neutral wire is essential for the receiver's operation. The terminal block accepts one wire of maximum 1.5 mm² per terminal.
Poznámka: Some users recommend using solid copper core cables instead of multi-strand aluminum for better connection stability.
Schémata zapojení:
- Connecting with an Existing Wall Switch (Two-Way Control): This setup allows both the traditional wall switch and the wireless transmitter to control the light.
Image: Detailed wiring diagram illustrating how to integrate the LoraTap receiver with a standard wall switch for two-way control.
- Direct Connection to Load (No Existing Wall Switch): Use this method if you are adding a new control point for a light fixture without a pre-existing wall switch.
Image: Comprehensive wiring diagrams for various installation scenarios, including direct connection to a lamp (Method 2).
- Two-Way Switch Functionality (Va-et-vient): The kit supports creating a two-way switch setup with your traditional switch. Refer to the provided wiring diagrams for specific connections.
The compact size of the receiver (approx. 46x46x18mm) allows for installation within existing switch boxes or ceiling rose enclosures, provided there is sufficient space and a neutral wire.
5.2 Montáž vysílače
The wireless transmitter can be used in two ways: fixed to a wall or as a portable remote control.
- Opravený režim: Attach the wall plate to your desired location using the included double-sided adhesive tape or screws. The transmitter magnetically attaches to this plate.
- Přenosný režim: The transmitter can be easily removed from its magnetic wall plate to be used as a handheld remote control.
Image: The LoraTap wireless switch demonstrating both fixed wall-mounted and portable handheld usage modes.
Image: Instructions for installing the magnetic wall plate using either adhesive tape or screws.
6. Nastavení a párování
The LoraTap Wireless Switch Kit typically comes pre-paired from the factory, ready for immediate use after installation. However, if you need to pair additional transmitters to a receiver, or re-pair existing ones, follow these steps:
- Ensure the receiver module is powered on.
- Press and hold the pairing button on the receiver module (usually a small button, refer to the receiver diagram for exact location) until the indicator light starts flashing.
- Within 5 seconds of the indicator light flashing, press the desired button on your wireless transmitter.
- The receiver's indicator light will stop flashing, confirming successful pairing.
Multiple transmitters can be paired to a single receiver, and one transmitter can control multiple receivers. Each product has an independent ID, preventing interference between multiple units.
Image: Illustration demonstrating that multiple LoraTap wireless switch kits can operate simultaneously without signal interference.
7. Provoz
Once installed and paired, operate the switch by pressing the button on the wireless transmitter. The transmitter has a tactile button for ON/OFF control.
- Rozsah ovládání: The wireless signal has an indoor range of up to 30 meters and an outdoor range of up to 200 meters. It can effectively transmit through walls, windows, and ceilings.
- Kontrolka: The transmitter features a small indicator light that illuminates briefly when pressed, confirming signal transmission and indicating battery health. This light does not indicate the ON/OFF status of the connected load.
- Funkce paměti: The receiver module includes a memory function. If power is interrupted and then restored, the connected light will return to its last known state (ON or OFF) before the power cut.
Image: Visual representation of the wireless control range, demonstrating signal penetration through multiple walls.
Image: Demonstration of the memory function, showing the light returning to its previous state after a power interruption.
8. Údržba
8.1 Výměna baterie
The wireless transmitter is powered by a CR2032 lithium metal battery, which has a lifespan of over 10 years or approximately 220,000 clicks. When the indicator light on the transmitter becomes dim or fails to illuminate upon pressing, it's time to replace the battery.
- Opatrně otevřete vysílač casing (refer to the product diagram for the battery compartment location).
- Vyjměte starou baterii CR2032.
- Vložte novou baterii CR2032 kladnou (+) stranou nahoru.
- Zavřete vysílač casinbezpečně.
8.2 Čištění
Clean the surfaces of the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the plastic housing.
9. Řešení problémů
- Light does not respond to transmitter:
- Check if the receiver module is correctly wired and receiving power.
- Verify the transmitter battery. Replace the CR2032 battery if the indicator light is dim or not illuminating.
- Ensure the transmitter and receiver are paired. If not, follow the pairing instructions in Section 6.
- Confirm the transmitter is within the effective control range.
- Light flickers or remains dimly lit when OFF (especially with LED lights):
- This can occur due to residual voltage in the circuit. Ensure the neutral wire connection to the receiver is secure and correctly wired. In some cases, a capacitor may be needed across the load (light fixture) to absorb residual current, though this is not typically required for this product.
- Delay in response when using with a traditional wired switch:
- A slight delay (2-3 seconds) can sometimes be observed, especially if the traditional switch is toggled rapidly. This is generally a characteristic of the relay mechanism and not a fault.
- Traditional wired switch does not control the light after receiver installation:
- Double-check the wiring connections for the traditional switch (S1, S2 terminals on the receiver). Ensure the neutral wire is not interrupted by the traditional switch.
10. Záruka a podpora
The LoraTap Wireless Switch Kit SS9111Q1 comes with a 5-letá záruka. This warranty covers defects in materials and workmanship under normal use. For warranty claims or technical support, please contact your retailer or LoraTap customer service with your purchase details.
The product is CE and RoHS certified, ensuring compliance with European safety, health, and environmental protection requirements.
