1. Bezpečnostní pokyny
Před instalací a použitím si prosím pečlivě přečtěte tyto pokyny. Uschovejte si tento návod pro budoucí použití.
- Installation must be carried out by a qualified electrician in accordance with national wiring regulations.
- Před instalací, údržbou nebo opravou se ujistěte, že je odpojeno napájení.
- Do not exceed the maximum load ratings specified in this manual.
- This device is designed for outdoor use and has an IP65 protection rating, making it dust-tight and protected against water jets.
- Zařízení nerozebírejte ani neupravujte.
2. Obsah balení
- 1 x SEBSON IR_CEIL_C Outdoor Motion Detector IP65
- Montážní materiál (šrouby, hmoždinky)
- Návod k použití
3. Konec produktuview
The SEBSON IR_CEIL_C is an infrared motion detector designed for ceiling surface mounting in outdoor environments. It features a 360-degree detection angle and a maximum range of 20 meters, making it suitable for various applications such as activating outdoor lighting.
4. Instalace
This motion detector is designed for surface mounting on ceilings. Ensure the mounting surface is stable and suitable for the device's weight.
4.1 Místo montáže
- Mount the detector at a height between 2.2 meters and 4 meters for optimal detection.
- Avoid mounting near heat sources (e.g., air vents, direct sunlight) or objects that might obstruct the detection area.
- Consider the detection range and angle (360° with a maximum 20m diameter) to cover the desired area effectively.
4.2 Zapojení
The device requires a 3-wire connection. Ensure the power supply is OFF before proceeding.
- Open the detector housing carefully.
- Connect the live (L), neutral (N), and switched live (L') wires to the corresponding terminals.
- Secure the cables using the provided strain relief.
- Close the housing, ensuring a tight seal for IP65 protection.
4.3 Rozměry
5. Provoz
Once properly installed and configured, the SEBSON IR_CEIL_C motion detector will automatically activate the connected lighting when it detects movement within its detection zone and when the ambient light level falls below the set threshold. The light will remain on for the duration set by the 'TIME' dial and then turn off automatically if no further motion is detected.
6. Úpravy
The motion detector features two adjustable dials to customize its operation:
- ČAS (Trvání): This dial controls how long the connected light remains on after motion is detected. The adjustable range is from 10 seconds to 30 minutes. Turn the dial clockwise to increase the duration and counter-clockwise to decrease it.
- LUX (citlivost na světlo): This dial determines the ambient light level at which the motion detector becomes active. The adjustable range is from 3 LUX (darkness) to 2000 LUX (daylight). Turn the dial towards the 'sun' symbol for activation during daylight and towards the 'moon' symbol for activation only in low light conditions.
To access the adjustment dials, carefully open the detector housing as shown in the installation section.
7. Specifikace
| Funkce | Specifikace |
|---|---|
| Výrobce | SEBSON |
| Číslo modelu | IR_CEIL_C |
| Rozměry (D x Š x V) | 11.3 x 11.3 x 4.5 cm |
| Hmotnost | 145 gramů |
| Barva | Bílý |
| Materiál | Plast |
| Třída ochrany | IP65 |
| svtage | 230 voltů |
| Max. Incandescent Load | 2000 wattů |
| Max. LED/Energy Saving Lamp Zatížení | 1000 wattů |
| Rozsah detekce | Max. 20 Meters |
| Detekční úhel | 360° |
| Úprava časového zpoždění | 10 sekund - 30 minut |
| Light Sensitivity Adjustment | 3–2000 luxů |
| Typ montáže | Stropní povrchová montáž |
| Zdroj napájení | Elektrický kabel |
8. Řešení problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Světlo se nerozsvítí, když je detekován pohyb. | No power supply; LUX setting too high (daylight mode); faulty wiring; bulb failure. | Check power connection; adjust LUX setting to a lower value (moon symbol); verify wiring connections; replace bulb. |
| Světlo svítí nepřetržitě. | Constant motion in detection area; faulty sensor; wiring error. | Ensure no continuous motion; check for obstructions; verify wiring (L' connected correctly); if problem persists, contact support. |
| Light turns on too frequently or for too long. | TIME setting too long; LUX setting too low; detection area too wide. | Adjust TIME dial to a shorter duration; adjust LUX dial to a higher value; reposition detector or block part of the detection area if possible. |
| Detekční dosah je příliš krátký. | Mounting height too low; obstructions; temperature interference. | Ensure mounting height is within recommended range (2.2m-4m); remove obstructions; avoid mounting near strong heat sources. |
9. Údržba
The SEBSON IR_CEIL_C motion detector requires minimal maintenance. To ensure optimal performance:
- Pravidelně čistěte čočku snímače měkkým hadříkemamp cloth to remove dust or dirt that may affect detection. Do not use abrasive cleaners.
- Regularly check for any physical damage to the housing or wiring.
10. Záruka a podpora
For warranty information or technical support, please refer to the purchase documentation or contact SEBSON customer service directly. Keep your proof of purchase for any warranty claims.
