Uživatelská příručka k postroji FallTech FT Iron Worker

Zavedení

This manual provides essential information for the proper use, care, and maintenance of the FallTech FT Iron Worker Body Harness. This harness is designed for fall protection in various industrial and construction environments, specifically tailored for ironwork. Adherence to these instructions is crucial for user safety and product longevity. Always inspect the harness before each use.

Bezpečnostní informace

VAROVÁNÍ: Nedodržení těchto pokynů může vést k vážnému zranění nebo smrti.

• Always inspect the harness for damage, wear, or defects before each use.
• Ensure all buckles and adjusters are securely fastened and properly adjusted.
• The harness must be used as part of a complete personal fall arrest system.
• Do not modify the harness in any way.
• Consult a qualified person for training on proper fall protection procedures.
• Maximum weight capacity for this harness is 425 lbs (including tools and clothing).

Komponenty skončilyview

The FallTech FT Iron Worker Body Harness features several key components designed for comfort and safety.

Obrázek 1: Plná View of the FallTech FT Iron Worker Body Harness. This image displays the complete harness, highlighting its various straps, buckles, and D-rings from a side perspective.

Obrázek 2: Přední strana View of the FallTech FT Iron Worker Body Harness. This image shows the front of the harness, including the chest strap, shoulder padding, and waist belt with quick-connect buckles.

Obrázek 3: Zpět View of the FallTech FT Iron Worker Body Harness. This image illustrates the back of the harness, featuring the dorsal D-ring, shoulder straps, and back padding.

• Hřbetní D-kroužek: Located on the back, used as the primary attachment point for fall arrest.
• Boční D-kroužky: Located on the hips, used for work positioning or restraint.
• Ramenní popruhy: Adjustable straps that go over the shoulders, often padded for comfort.
• Popruh na hrudi: Secures the shoulder straps across the chest, typically with a quick-connect buckle.
• Popruhy na nohy: Adjustable straps that go around the legs, usually with quick-connect buckles.
• Opasek: Provides support and attachment points for tools, with a belt buckle.
• Torso Adjusters: Mechanisms for adjusting the fit of the harness vertically.

Setup and Donning

Follow these steps to properly don and adjust your FallTech FT Iron Worker Body Harness:

1. Zkontrolujte kabelový svazek: Before each use, visually inspect the entire harness for cuts, fraying, broken stitches, heat damage, chemical damage, or any other signs of wear or damage. Ensure all buckles and D-rings are free of deformation or corrosion.
2. Hold by Dorsal D-Ring: Hold the harness by the dorsal D-ring (back D-ring) to allow the straps to fall into place.
3. Don Shoulder Straps: Slip the shoulder straps over your shoulders, as if putting on a vest. Ensure the dorsal D-ring is centered on your back, between your shoulder blades.
4. Připojení nožních popruhů: Bring the leg straps between your legs and connect them to the corresponding buckles on the waist belt or main harness body. Ensure the straps are not twisted.
5. Connect Chest Strap: Fasten the chest strap across your chest. Adjust its position so it is approximately mid-chest level.
6. Adjust Leg Straps: Tighten the leg straps so they are snug but allow for full range of motion. You should be able to slide your flat hand between the strap and your leg.
7. Nastavení ramenních popruhů: Pull the shoulder strap adjusters to remove any slack. The harness should fit snugly without restricting movement.
8. Adjust Torso/Waist Belt: Adjust the torso straps and waist belt to ensure a snug fit around your waist and hips. The waist belt should sit comfortably and securely.
9. Závěrečná kontrola: Perform a final visual check to ensure all straps are flat, not twisted, and all buckles are securely fastened. The harness should fit snugly, allowing for comfortable movement without excessive slack.

Provoz a použití

The FallTech FT Iron Worker Body Harness is designed for fall arrest, work positioning, and restraint applications. Always connect to an approved anchorage point and compatible connecting device.

• Zastavení pádu: Connect a compatible lanyard or self-retracting lifeline to the dorsal D-ring. Ensure the anchorage point is capable of supporting 5,000 lbs (22.2 kN) per worker or meets OSHA/ANSI requirements.
• Pracovní pozice: Use the side D-rings for work positioning. These are designed to support a worker in a suspended position, allowing hands-free operation. Always use a separate fall arrest system when using work positioning.
• Omezení: The side D-rings can also be used for restraint, preventing a worker from reaching a fall hazard.
• Upevnění nástroje: The waist belt is designed to accommodate tool bags and other accessories. Ensure that the combined weight of tools and the user does not exceed the harness's maximum weight capacity.
• Post-Fall Procedure: In the event of a fall, immediately remove the harness from service. Do not use it again. The harness must be inspected by a competent person or destroyed. Seek medical attention if necessary.

Údržba

Správná údržba prodlužuje životnost vašeho postroje a zajišťuje jeho trvalou bezpečnost.

Čištění

• Pouze ruční mytí.
• Use a mild soap or detergent and lukewarm water.
• Scrub the harness with a stiff brush to remove dirt and grime.
• Důkladně opláchněte čistou vodou, dokud neodstraníte všechny zbytky mýdla.
• Hang to air dry in a clean, shaded area away from direct sunlight, heat, or open flame. Do not machine wash or dry.

Inspekce

• Před každým použitím: Perform a visual inspection as described in the

  Související dokumenty - 8144QCSM

  	Průvodce velikostmi postrojů pro ochranu proti pádu | FallTech Najděte si perfektní velikost pro váš ochranný postroj proti pádu s pomocí komplexního průvodce velikostmi od FallTech. Naučte se, jak změřit obvod hrudníku, pasu a stehen pro optimální bezpečnost a pohodlí.
  	Uživatelská příručka k celotělovému postroji FallTech - MFBH04 Komplexní uživatelská příručka k celotělovému postroji FallTech (model MFBH04). Zahrnuje bezpečnostní varování, popis, použití, systémové požadavky, instalaci, použití, údržbu, kontrolu a definice ochrany proti pádu.
  	Nastavitelný stativ FallTech 7275: Instalační, provozní a údržbářský manuál Uživatelská příručka pro nastavitelný stativ FallTech 7275 s podrobnými pokyny k instalaci, provozu, údržbě a bezpečnostním pokynům pro zachycení pádu, pracovní polohování a záchranné aplikace.
  	Uživatelská příručka a instalační průvodce pro nástroj FallTech pro smršťování za studena This user manual provides essential safety information, application details, installation procedures, maintenance guidelines, and specifications for FallTech Cold Shrink Tool Attachments. Designed for dropped object prevention, these attachments are compatible with FallTech tool tethers and anchors, ensuring secure tool tethering for various hand and power tools. Includes models 5410A5, 5411A5, and 5412A5, meeting ANSI/ISEA 121-2018 standards.
  	Prohlášení o shodě a zkušební protokol pro nastavitelný zádržný spojovací prvek FallTech Prohlášení o shodě a podrobný protokol o zkoušce pro nastavitelný zádržný spojovací prvek FallTech 8209, potvrzující shodu s normami ANSI Z359.3-2019 a ANSI/ISEA 125-2014.
  	Uživatelská příručka k kotvám pro dřevěné rámové konstrukce FallTech FallTech's User Instruction Manual for Wood Frame Structure Anchors provides essential guidance on the safe installation, operation, and maintenance of their Type A, B, and C anchors. Compliant with ANSI Z359 and OSHA standards, this manual is crucial for fall protection and restraint systems on wood-framed structures.