1. Konec produktuview
The Marantec Digital 520 is a wall-mounted digital transmitter designed for convenient control of garage door operators and external gates. It utilizes Marantec's proprietary bi-linked radio system, ensuring high security and reliable operation.
Mezi klíčové vlastnosti patří:
- Bi-linked Wireless Standard: Operates on an 868 MHz frequency with 128-bit encryption, similar to online banking security protocols.
- Technologie plovoucího kódu: The transmission code changes with each operation, making signal copying or decryption virtually impossible.
- Dva kanály: Allows control of up to two distinct targets or functions, such as two separate garage doors or a garage door and a gate.
- Uživatelsky přívětivý design: Features two large, comfortable buttons with a noticeable pressure point for easy operation.
- LED indikátor: A red LED light confirms command transmission.
- Univerzální kompatibilita: Works with all Marantec drive operators and can also control other manufacturers' operators via a universal bi-linked receiver.
2. Nastavení a instalace
The Digital 520 transmitter is designed for easy wall mounting without the need for electrical wiring.
2.1 Obsah balení
Před zahájením instalace se ujistěte, že jsou přítomny všechny komponenty:
- Digital 520 Wall-Mounted Transmitter
- Integrated Wall Bracket
- CR2032 Battery (pre-installed or included)
- Montážní šrouby a hmoždinky
2.2 Instalace/kontrola baterie
The transmitter is powered by a standard CR2032 coin cell battery. If not already installed, or if replacing, ensure correct polarity.
- Carefully open the battery compartment, usually located on the side or back of the unit.
- Vložte baterii CR2032 kladným pólem (+) nahoru.
- Bezpečně uzavřete přihrádku na baterie.
2.3 Montáž na stěnu
The integrated wall bracket simplifies installation.
- Choose a suitable location on a wall, preferably near the garage door or gate, within easy reach.
- Hold the transmitter (with the integrated bracket) against the wall at the desired height and mark the positions for the mounting screws.
- Drill pilot holes at the marked positions. Insert wall plugs if necessary.
- Secure the transmitter to the wall using the provided screws. Ensure it is firmly attached.
2.4 Programming/Pairing
To operate your garage door or gate, the Digital 520 transmitter must be paired with your Marantec bi-linked receiver. Refer to your garage door operator's manual for specific pairing instructions, as procedures may vary. Generally, this involves:
- Activating the programming mode on your Marantec receiver (often by pressing a 'Learn' or 'Program' button).
- Pressing the desired button on the Digital 520 transmitter within a specified timeframe.
- Confirming successful pairing (e.g., by an LED on the receiver or a specific sound).
3. Návod k obsluze
The Digital 520 transmitter is designed for straightforward operation.
3.1 Controlling Your Device
Each of the two large buttons can be configured to control a specific function or device (e.g., open/close garage door 1, open/close garage door 2, activate partial opening, or ventilation function).
- To activate a programmed function, simply press the corresponding button firmly.
- The red LED indicator on the transmitter will illuminate briefly to confirm that a command signal has been sent.
4. Údržba
The Marantec Digital 520 requires minimal maintenance to ensure long-lasting performance.
4.1 Výměna baterie
When the red LED indicator on the transmitter becomes dim or fails to light up upon button press, it is time to replace the CR2032 battery. Follow the steps in Section 2.2 for battery installation.
4.2 Čištění
To clean the transmitter, wipe it with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the unit.
5. Řešení problémů
If you experience issues with your Digital 520 transmitter, try the following troubleshooting steps:
| Problém | Možná příčina | Řešení |
|---|---|---|
| Transmitter does not respond / LED does not light up. | Vybitá nebo slabá baterie. | Replace the CR2032 battery (see Section 4.1). |
| Transmitter LED lights up, but device does not respond. | Transmitter not paired or pairing lost. | Re-pair the transmitter with your receiver (see Section 2.4). Ensure you are within range of the receiver. |
| Přerušovaný provoz. | Weak battery or signal interference. | Replace battery. Check for sources of radio interference (e.g., other wireless devices, large metal objects). |
If the problem persists after attempting these solutions, please contact Marantec customer support.
6. Specifikace
| Atribut | Hodnota |
|---|---|
| Výrobce | Marantec |
| Číslo modelu položky | 161336 |
| Číslo dílu | 161336 |
| Rozměry produktu | 80 x 80 x 25 mm |
| Hmotnost položky | 90 g |
| Barva | Černý |
| Materiál | Plast |
| Number of Item Units | 1 |
| Baterie | 1 CR2032 (v ceně) |
| Typ baterie | Oxid manganičitý lithný |
| Bezdrátová frekvence | 868 MHz |
| Šifrování | 128bitový |
7. Záruka a podpora
Marantec products are manufactured in Germany to the highest quality standards, ensuring reliability and durability.
For warranty information, technical support, or service inquiries, please refer to the official Marantec website or contact your local Marantec dealer. Keep your purchase receipt as proof of purchase.
