1. Úvod
This manual provides instructions for the safe operation, maintenance, and troubleshooting of the Total Tools Air GA18 Brad Nailer. Please read this manual thoroughly before use to ensure proper and safe operation and to maximize the lifespan of your tool.
1.1 Bezpečnostní informace
Always wear appropriate personal protective equipment, including safety glasses and hearing protection, when operating the tool. Disconnect the air supply before making any adjustments, clearing jams, or performing maintenance. Keep hands and body parts clear of the discharge area and moving parts. This tool is designed for driving brad nails into wood and similar materials. Do not use for purposes other than its intended use.
2. Konec produktuview a Komponenty
The Total Tools Air GA18 Brad Nailer is an air-powered tool designed for efficient fastening of brad nails. Below is an illustration of the tool and its main components.
An image showing the Total Tools Air GA18 Brad Nailer inside its retail packaging, highlighting key features and specifications like GA18 model, 15mm (5/8") and 50mm (2") nail compatibility, and 1.25x1.0mm nail gauge.
2.1 klíčové komponenty
- Vstup vzduchu: Připojovací bod pro vzduchovou hadici.
- Spoušť: Activates the nail driving mechanism.
- Časopis: Holds the strip of brad nails.
- Nosník: Contact point with the workpiece, where nails exit.
- Nastavení hloubky: Mechanism to control the nail driving depth.
- Výfukový port: Releases compressed air.
- Bezpečnostní mechanismus: Prevents accidental firing.
3. Nastavení
3.1 Připojení k přívodu vzduchu
- Ujistěte se, že je vzduchový kompresor vypnutý a vzduchová hadice je bez tlaku.
- Connect the air hose to the tool's air inlet. Ensure a secure connection.
- Set the air compressor pressure to the recommended operating range, typically between 60-100 PSI (4.1-6.9 bar). Refer to the tool's specifications for precise pressure requirements.
3.2 Nabíjení hřebíků Brad
- Ujistěte se, že je nástroj odpojen od přívodu vzduchu.
- Zatáhněte za podavač zásobníku, dokud nezapadne na místo.
- Insert a strip of compatible brad nails (GA18, 1.25x1.0mm, 15mm-50mm length) into the magazine slot.
- Release the magazine follower to secure the nails. Ensure nails are seated correctly.
4. Návod k obsluze
4.1 Obecná obsluha
- Ensure all safety precautions are observed, including wearing safety glasses and hearing protection.
- Připojte nářadí k přívodu vzduchu.
- Place the nosepiece firmly against the workpiece where the nail is to be driven. The safety mechanism must be fully depressed.
- Depress the trigger to drive a nail.
- Release the trigger after each nail is driven.
4.2 Nastavení hloubky
The nail driving depth can be adjusted to suit different materials and desired finishes. Locate the depth adjustment knob or lever, typically near the nosepiece. Rotate or slide the adjuster to increase or decrease the nail depth. Always test the adjusted depth on a scrap piece of material before working on your final project.
5. Údržba
5.1 Denní údržba
- Disconnect the air supply from the tool after each use.
- Clean the tool's exterior with a dry, clean cloth to remove dust and debris.
- Apply a few drops of pneumatic tool oil into the air inlet daily or before each use to lubricate internal components.
5.2 Clearing Nail Jams
- Odpojení přívodu vzduchu: Crucially, disconnect the tool from the air compressor.
- Open Nosepiece Latch: If applicable, open the quick-release nosepiece latch.
- Remove Jammed Nails: Carefully remove any jammed nails or debris from the nosepiece and magazine area. Use pliers if necessary, but avoid forcing.
- Zavřete západku: Close the nosepiece latch securely.
- Test: Znovu připojte přívod vzduchu a vyzkoušejte nástroj na odpadním kusu materiálu.
6. Řešení problémů
This section addresses common issues you might encounter with your Total Tools Air GA18 Brad Nailer.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Nailer not firing | Low air pressure; No nails in magazine; Safety mechanism not fully depressed; Tool needs lubrication. | Check air supply and pressure; Reload magazine; Ensure nosepiece is firmly against workpiece; Apply pneumatic oil. |
| Nails not fully driven | Insufficient air pressure; Depth adjustment set too shallow; Incorrect nail length for material. | Increase air pressure; Adjust depth setting; Use appropriate nail length. |
| Nails jamming frequently | Incorrect nail size/type; Damaged or bent nails; Magazine issues; Tool needs cleaning/lubrication. | Use correct GA18 brad nails; Inspect nails before loading; Clean magazine; Lubricate tool. |
| Unikající vzduch z nástroje | Uvolněné spoje; Poškozené O-kroužky/těsnění. | Tighten air fittings; Inspect and replace worn O-rings/seals (professional service recommended). |
7. Specifikace
Technical specifications for the Total Tools Air GA18 Brad Nailer:
| Funkce | Detail |
|---|---|
| Výrobce | Celkový |
| Číslo dílu | GA18 |
| Číslo modelu položky | GA18 |
| Typ zdroje napájení | Vzduch |
| Compatible Nail Gauge | GA18 (1.25x1.0mm) |
| Kompatibilní délky nehtů | 15mm - 50mm (5/8" - 2") |
| Hmotnost položky | 2.26 kg |
| Rozměry balení | 29 x 26 x 6.2 cm |
| Jsou vyžadovány baterie? | Žádný |
| Barva | Multi |
8. Záruka a podpora
For warranty information, technical support, or service inquiries regarding your Total Tools Air GA18 Brad Nailer, please contact Total Tools customer service. It is recommended to keep your purchase receipt as proof of purchase for any warranty claims.
You can typically find contact details and further support resources on the official Total Tools webnebo prostřednictvím místního autorizovaného prodejce.
Poznámka: Neoprávněné opravy nebo úpravy mohou vést ke zrušení záruky na výrobek.
