AMONIDA TB446 SHT30 Temperature Humidity Sensor

1. Konec produktuview

The AMONIDA TB446 SHT30 is a high-precision digital temperature and humidity sensor module designed for various applications requiring accurate environmental monitoring. It features a real I2C interface for communication and provides fully calibrated, linearized, and temperature-compensated digital output.

This sensor is compatible with both 3V and 5V microcontrollers, making it versatile for integration into different systems. It offers a wide measurement range for both temperature and humidity, ensuring reliable data collection.

Figure 1: Two AMONIDA SHT30 Temperature Humidity Sensor modules with their respective connecting cables, illustrating the compact design and wiring.

2. Klíčové vlastnosti

• Digitální výstup: Provides fully calibrated, linearized, and temperature-compensated digital signals.
• Rozhraní I2C: Real I2C communication with speeds up to 1MHz.
• Wide Voltage Kompatibilita: Operates with 2.5V to 5.5V DC power supply.
• Rozsah teplot: Measures from -40°C to 125°C (operational environment -40°C to 80°C due to cable/shell limitations).
• Rozsah vlhkosti: Measures 0% to 100% Relative Humidity (RH).
• Vysoká přesnost: ±0.2°C for temperature, ±2% RH for humidity.
• Standard Connector: XH2.54 4P terminal for easy connection.

Figure 2: The SHT30 sensor module shown against a circuit board background, emphasizing its digital output capabilities with calibration, linearization, and temperature compensation.

3. Nastavení a připojení

Follow these steps to properly connect your AMONIDA TB446 SHT30 sensor:

1. Identifikujte připojení: The sensor uses an XH2.54 4P terminal. The wires are typically color-coded for easy identification:
   • Červený: VCC (Power Supply, 2.5V-5.5V DC)
   • Černý: GND (zem)
   • Žlutá: SDA (I2C Data Line)
   • Bílý: SCL (I2C Clock Line)
2. Připojte napájení: Connect the Red wire to your microcontroller's 2.5V-5.5V DC power output and the Black wire to the microcontroller's Ground (GND).
3. Connect I2C Interface: Connect the Yellow wire (SDA) to your microcontroller's I2C Data pin and the White wire (SCL) to your microcontroller's I2C Clock pin. Ensure your microcontroller's I2C pins are properly configured.
4. Zabezpečená připojení: Ensure all connections are firm and correctly aligned to prevent short circuits or improper data transmission.

The I2C address for the SHT30 sensor is 0x44.

4. Návod k obsluze

Once connected, the SHT30 sensor communicates via the I2C protocol. You will need to write code for your microcontroller (e.g., Arduino, Raspberry Pi) to interact with the sensor.

1. Inicializace I2C: In your code, initialize the I2C communication bus on your microcontroller.
2. Send Measurement Commands: Send appropriate I2C commands to the sensor to initiate a temperature and humidity measurement. Refer to the SHT30 datasheet for specific command details (e.g., single shot measurement, periodic measurement).
3. Číst data: After a measurement is complete, read the digital output data from the sensor via the I2C bus. The sensor will provide raw digital values for temperature and humidity.
4. Convert Data: Convert the raw digital values into meaningful temperature (°C or °F) and humidity (%RH) readings using the conversion formulas provided in the SHT30 datasheet. Many libraries for common microcontrollers handle this conversion automatically.

Figure 3: The SHT30 sensor module displayed with a focus on its humidity measurement range of 0-100% RH, set against a digital circuit background.

5. Údržba

The AMONIDA TB446 SHT30 sensor is designed for reliable operation with minimal maintenance. Observe the following guidelines:

• Podmínky prostředí: While the sensor itself can measure up to 125°C, the external shell and connecting wires are rated for -40°C to 80°C. Ensure the sensor is operated within this environmental temperature range to prevent damage to the housing or cables.
• Čistota: Keep the sensor clean and free from dust, dirt, or moisture accumulation on the sensing element, as this can affect accuracy. Use a soft, dry cloth for cleaning if necessary. Avoid using liquids or abrasive materials.
• Fyzická ochrana: Protect the sensor from physical impact or excessive mechanical stress.
• Skladování: When not in use, store the sensor in a dry, non-condensing environment within its specified temperature range.

6. Řešení problémů

If you encounter issues with your SHT30 sensor, consider the following troubleshooting steps:

• No Readings or Incorrect Readings:
  • Zkontrolujte zapojení: Verify that all connections (VCC, GND, SDA, SCL) are correctly made and secure.
  • Napájení: Ensure the sensor is receiving adequate power (2.5V-5.5V DC).
  • Adresa I2C: Confirm that the I2C address (0x44) in your code matches the sensor's address.
  • I2C Pull-ups: Ensure your I2C bus has appropriate pull-up resistors (typically 4.7kΩ) on SDA and SCL lines, if not already provided by your microcontroller board.
  • Logika kódu: Review your microcontroller code for correct I2C initialization, command sending, and data reading/conversion.
  • Environmentální limity: Check if the sensor is operating outside its specified environmental temperature or humidity range, which can affect performance.
• Přerušovaná čtení:
  • Uvolněná připojení: Re-check all wiring for any loose contacts.
  • Hluk: Ensure the sensor and its wiring are shielded from excessive electrical noise, especially in industrial environments.

7. Specifikace

Figure 4: The SHT30 sensor module with its connecting cable, illustrating the approximate cable length of 36 cm (14.2 inches).

8. Záruka a podpora

For warranty information and technical support, please refer to the documentation provided with your purchase or contact AMONIDA customer service. Keep your purchase receipt for warranty claims.