HUNTER X2-600 6-Station Sprinkler Timer Controller

1. Úvod a konecview

The Hunter X2-600 is a 6-station sprinkler timer controller designed for efficient and convenient management of irrigation systems. This controller is Wi-Fi ready, allowing for advanced scheduling and remote management when paired with the optional Hunter Hydrawise Wi-Fi module. It provides reliable performance for maintaining healthy landscapes through routine installations and real-time status updates.

2. Bezpečnostní informace

Please read all safety instructions before installation and operation. Failure to follow these instructions may result in property damage, personal injury, or death.

• Elektrická bezpečnost: Always disconnect power to the controller before performing any wiring or maintenance. Ensure all wiring connections are secure and comply with local electrical codes.
• Venkovní použití: While designed for outdoor use, protect the controller from direct water spray and extreme weather conditions to ensure longevity.
• Děti: Uchovávejte ovladač mimo dosah dětí.
• Kvalifikovaný personál: Installation and servicing should be performed by qualified personnel where necessary.

3. Obsah balení

Ověřte, zda jsou v balení přítomny všechny položky:

• Hunter X2-600 Controller Unit
• Napájecí kabel (předpřipojený)
• Montážní materiál (šrouby, hmoždinky)
• Uživatelská příručka (tento dokument)

4. Nastavení a instalace

4.1 Montáž regulátoru

Select a suitable location for mounting the controller. It should be protected from direct sunlight and extreme weather, and close to a power outlet and irrigation valves.

1. Use the provided mounting template or hold the controller against the wall and mark the top mounting hole.
2. Vyvrtejte pilotní otvor a v případě potřeby do něj vložte hmoždinku.
3. Install a screw into the top hole, leaving approximately 1/8 inch (3 mm) exposed.
4. Hang the controller on the top screw.
5. Mark the locations for the two bottom mounting holes.
6. Remove the controller, drill pilot holes, and insert wall anchors.
7. Re-hang the controller and secure it with the bottom screws.

Obrázek 4.1: Přední strana view of the Hunter X2-600 controller.

4.2 Zapojení regulátoru

Ensure power is disconnected before wiring. The X2-600 supports up to 6 irrigation zones, a common wire, and sensor connections.

1. Common Wire (COM): Connect the common wire from your irrigation valves to the terminal labeled 'COM'. This is typically a white wire.
2. Zone Wires (1-6): Connect each individual zone wire from your irrigation valves to the corresponding numbered terminal (1 through 6).
3. Sensor Wires (SEN): If using a rain or soil sensor, connect its wires to the 'SEN' terminals. Refer to your sensor's manual for specific wiring.
4. 24VAC Power: The controller comes with a pre-attached power cord. Plug it into a standard 120V AC outlet. The 24VAC terminals are for optional external power sources or accessories.

Figure 4.2: Wiring terminals of the Hunter X2-600 controller.

4.3 Initial Power-Up and Wi-Fi Readiness

Once wired, connect the power cord to an electrical outlet. The controller display will illuminate. The X2-600 is Wi-Fi ready, meaning it can be upgraded to smart control by purchasing and installing a separate Hunter Hydrawise Wi-Fi module. This module plugs directly into the controller and enables remote management via the Hydrawise app.

Obrázek 4.3: Zpět view of the Hunter X2-600 controller with power cord.

5. Návod k obsluze

The X2-600 features a simple dial and button interface for programming.

5.1 Nastavení data a času

1. Turn the dial to the 'Date/Time' position.
2. Pomocí tlačítek se šipkami nastavte rok, měsíc, den, hodinu a minutu.
3. Press the 'PRG' button to confirm each setting.

5.2 Programming Irrigation Schedules

The controller allows for multiple independent programs (A, B, C).

1. Vyberte program: Turn the dial to 'PRG' and use the arrow buttons to select Program A, B, or C.
2. Nastavit časy zahájení: Turn the dial to 'Start Times'. Use the arrow buttons to set up to four start times per program.
3. Nastavte doby běhu: Turn the dial to 'Run Times'. For each zone (1-6), use the arrow buttons to set the desired watering duration in minutes.
4. Nastavte dny vody: Turn the dial to 'Water Days'. Use the arrow buttons to select specific days of the week for watering, or choose interval watering (e.g., every 2 days).

5.3 Ruční provoz

Ruční spuštění jedné stanice nebo všech stanic:

• Turn the dial to 'Manual'.
• Use the arrow buttons to select the desired zone or 'ALL' for all zones.
• Press the 'PRG' button to start the manual run.

5.4 Sezónní úprava

The 'Seasonal Adjust' feature allows you to quickly increase or decrease watering durations for all zones in a program by a percentage, without reprogramming individual run times.

• Turn the dial to 'Seasonal Adjust'.
• Use the arrow buttons to adjust the percentage (např. 100 % pro normální, 50 % pro poloviční, 150 % pro vyšší).

5.5 Wi-Fi Control (with optional module)

If the Hunter Hydrawise Wi-Fi module is installed, you can manage your controller remotely using the Hydrawise app on your smartphone or tablet. This includes setting schedules, monitoring water usage, and receiving alerts. Refer to the Hydrawise module's specific instructions for setup and app usage.

6. Údržba

The Hunter X2-600 controller requires minimal maintenance.

• Čištění: Pravidelně otírejte vnější povrch ovladače měkkým hadříkemamp tkanina. Nepoužívejte abrazivní čisticí prostředky nebo rozpouštědla.
• Spojení: Každoročně kontrolujte všechna elektrická připojení, abyste se ujistili, že jsou bezpečná a bez koroze.
• Zima: In regions with freezing temperatures, disconnect the controller from power and drain the irrigation system to prevent damage from freezing water.

7. Řešení problémů

Běžné problémy a jejich řešení naleznete v následující tabulce:

8. Specifikace

• Model: X2-600
• stanice: 6
• Příkon: 120V AC (with attached plug)
• výstup: 24V AC
• Rozměry (balení): 10.43 x 8.62 x 4.29 palce
• Hmotnost položky: 3.54 libry
• Barva: Bílý
• Počet nastavení: 2 (likely referring to programs A/B)
• Velikost obrazovky: 6 Inches (referring to the overall display area)
• UPC: 611698666555

9. Záruka a podpora

Hunter Industries provides a manufacturer's warranty for the X2-600 controller. For specific warranty terms, duration, and conditions, please refer to the warranty card included with your product or visit the official Hunter Industries website. For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact Hunter customer service or visit their online support resources.

Hunter Industries Official Webmísto: www.hunterindustries.com