1. Úvod
This manual provides detailed instructions for the installation, operation, and maintenance of your Phanteks Eclipse P500 Air Mid Tower Computer Case. Please read this manual thoroughly before beginning assembly or use to ensure proper functionality and safety.
The Phanteks Eclipse P500 Air is a mid-tower chassis designed for high airflow performance and versatile component support, including ATX, Micro ATX, Mini ITX, and E-ATX motherboards. It features a steel chassis with a tempered glass side panel and comes with three pre-installed 140mm D-RGB fans in the front.
Obrázek 1: Přední strana view of the Phanteks Eclipse P500 Air Mid Tower Computer Case.
2. Nastavení a instalace
Follow these steps to install your computer components into the Phanteks Eclipse P500 Air chassis.
2.1 Vybalení a počáteční kontrola
- Opatrně vyjměte podvozek z obalu.
- Inspect the chassis for any signs of damage during transit.
- Ensure all accessories (screws, cable ties, manual) are present.
Obrázek 2: Rozložené view showing removable panels and components for assembly.
2.2 Demontáž bočních panelů
The tempered glass side panel is hinged and secured with magnets. Gently pull the panel open to access the interior. The solid side panel can be removed by unscrewing the thumbscrews at the rear and sliding it off.
2.3 Instalace základní desky
- Install the necessary motherboard standoffs for your motherboard form factor (ATX, Micro ATX, Mini ITX, E-ATX).
- Opatrně umístěte základní desku na distanční sloupky a zajistěte ji šrouby.
Obrázek 3: Interiér view of the chassis, illustrating motherboard mounting area and fan locations.
2.4 Instalace úložného disku
The case supports up to 10 x 3.5" internal bays and 3 x 2.5" internal bays.
- 3.5" disky: Utilize the drive cages located in the PSU shroud area or behind the motherboard tray.
- 2.5" disky: Mount 2.5" SSDs/HDDs to the dedicated brackets behind the motherboard tray.
Obrázek 4: Zadní interiér view, highlighting cable management channels and 2.5" drive mounts.
2.5 Instalace napájecího zdroje
Install your ATX power supply into the dedicated compartment at the bottom rear of the chassis. Secure it with screws from the rear.
2.6 Instalace grafické karty a rozšiřující karty
- Remove the necessary PCI slot covers from the rear of the chassis.
- Insert your graphics card or other expansion cards into the motherboard's PCIe slots and secure them with screws.
- The case supports 7+3 PCI slots, allowing for vertical GPU mounting with an optional riser cable (not included).
Figure 5: Rear exterior view, detailing the PCI expansion slots and rear fan mount.
2.7 Správa kabelů
Utilize the integrated Velcro straps and cable ties provided to route and secure cables behind the motherboard tray. This improves airflow and aesthetics.
3. Provoz
The Phanteks Eclipse P500 Air features convenient front I/O ports and integrated D-RGB lighting controls.
3.1 Přední vstupní/výstupní panel
The top front panel provides access to essential controls and ports:
- Vypínač: Zapnutí nebo vypnutí systému.
- Tlačítko režimu LED: Cycles through various D-RGB lighting effects.
- LED Color Button: Changes the color of the D-RGB lighting.
- 2 porty USB 3.0: Pro připojení zařízení s rozhraním USB 3.0.
- Konektor mikrofonu: Pro audio vstup.
- Sluchátkový jack: Pro audio výstup.
Figure 6: Close-up of the top front I/O panel, showing USB ports, audio jacks, and LED controls.
3.2 D-RGB Lighting Control
The three pre-installed 140mm D-RGB fans are controlled via the integrated D-RGB controller. Use the LED Mode and LED Color buttons on the front I/O panel to customize the lighting. The D-RGB lighting can also be optionally synchronized with compatible motherboards and software.
Figure 7: Illustration of the integrated D-RGB lighting effects on the front fans.
4. Údržba
Pravidelná údržba pomáhá zajistit optimální výkon a dlouhou životnost vaší počítačové skříně.
4.1 Čištění prachového filtru
The Eclipse P500 Air features integrated dust filters on the front, top, and bottom (PSU intake) to prevent dust buildup. Regularly clean these filters to maintain optimal airflow.
- Přední filtr: The front mesh panel acts as a dust filter. It can be removed for cleaning.
- Horní filtr: The magnetic top filter can be easily lifted off for cleaning.
- Spodní filtr: The PSU intake filter slides out from the rear for cleaning.
Use compressed air or a soft brush to remove accumulated dust. Do not use harsh chemicals or abrasive materials.
Figure 8: Detail of the ultra-fine mesh front panel, designed for dust filtration and airflow.
4.2 Obecné čištění
Otřete vnější povrchy pouzdra měkkým,amp cloth. Avoid direct contact with electronic components inside the case.
5. Řešení problémů
This section addresses common issues you might encounter during the setup or operation of your Phanteks Eclipse P500 Air case.
- Systém se nezapíná:
- Ujistěte se, že je zdroj napájení správně připojen k zásuvce ve zdi a zapnutý.
- Verify that the power switch cable from the case is correctly connected to the motherboard's front panel header.
- Check all internal power connections (24-pin ATX, 8-pin CPU, PCIe power for GPU).
- D-RGB Fans Not Lighting Up:
- Confirm that the D-RGB cables from the fans are correctly connected to the integrated D-RGB controller or your motherboard's D-RGB header.
- Press the LED Mode and LED Color buttons on the front I/O panel to cycle through effects and colors.
- If connected to the motherboard, ensure the motherboard's RGB software is installed and configured correctly.
- Poor Airflow/High Temperatures:
- Clean all dust filters (front, top, bottom).
- Ensure fans are oriented correctly for optimal airflow (front intake, rear/top exhaust).
- Verify that no cables are obstructing airflow inside the case.
- Front USB Ports Not Functioning:
- Check that the USB 3.0 header cable from the case is securely connected to the corresponding header on your motherboard.
6. Specifikace
Below are the detailed specifications for the Phanteks Eclipse P500 Air Mid Tower Computer Case (PH-EC500ATG_DWT01).
Figure 9: Manufacturer's specification table for the Eclipse P500 Air.
| Funkce | Detail |
|---|---|
| Číslo modelu | PH-EC500ATG_DWT01 |
| Form Factor | Střední věž |
| Rozměry (DxŠxV) | 240 x 510 x 505 mm (9.45 x 20.1 x 19.9 palce) |
| Materiály | Steel Chassis, Tempered Glass |
| Podpora základní desky | E-ATX (up to 280mm wide), ATX, Micro ATX, Mini ITX, Mini ITX |
| Přední I/O | 2 x USB 3.0, Microphone, Headphone, Power Button, LED Mode Button, LED Color Button |
| Internal 3.5" Bay | 10 (2x included, also supports 2.5" drives) |
| Internal 2.5" Bay | 3 (3x included) |
| PCI sloty | 7 + 3 (vertical) |
| Předinstalované ventilátory | 3 x 140mm D-RGB fans (Front) |
| Podpora ventilátoru (přední) | 3 x 120 mm nebo 3 x 140 mm |
| Podpora ventilátoru (horní) | 3 x 120 mm nebo 2 x 140 mm |
| Podpora ventilátoru (zadní) | 1 x 120 mm nebo 1 x 140 mm |
| Držák chladiče (přední) | Up to 360mm or 420mm |
| Držák chladiče (horní) | Up to 360mm or 280mm |
| Držák chladiče (zadní) | 120 mm nebo 140 mm |
| Vyčištění GPU | 435 mm / 17.2 palce |
| Výška chladiče CPU | 190 mm / 7.5 palce |
| Délka PSU | 195 mm (250 mm if 2 HDD brackets are removed) |
| Čistá hmotnost | 8 kg / 17.6 liber |
Figure 10: Visual representation of fan and radiator mounting options within the chassis.
7. Záruka a podpora
Phanteks provides a manufacturer's warranty for this product.
- Záruční doba: 5 Years Manufacturer Warranty.
- For warranty claims or technical support, please contact Phanteks customer service or visit their official webmísto.
- Uschovejte si doklad o koupi pro ověření záruky.
For further assistance, refer to the official Phanteks webwebu nebo kontaktujte jejich kanály podpory.