DIGITEN DFC15 Water Flow Control System

Zavedení

This manual provides detailed instructions for the installation, operation, and maintenance of the DIGITEN DFC15 Water Flow Control System. This system is designed for precise measurement and control of water flow, suitable for various applications requiring quantitative liquid dispensing.

Obsah balení

The DIGITEN DFC15 Water Flow Control System package includes the following components:

• 1 x DFC15 Controller
• 1 x G3/4" Flow Sensor
• 1 x G3/4" Electric Solenoid Valve (Normally Closed)
• 1 x DC 12V napájecí adaptér
• 1 x snímač teploty
• 1 x Uživatelská příručka

Konecview of all components included in the DIGITEN Water Flow Control System kit, featuring the DFC15 controller, G3/4" flow sensor, G3/4" solenoid valve, power adapter, and temperature sensor.

Technické specifikace

DFC15 Controller

• Požadavek na napájení: 12V DC
• Napájecí adaptér: Input: 100-240VAC; Output: 12VDC, max 2A
• Adapter Lead Length: 1m
• Přesnost měření: ±1 %
• Output for Solenoid Valve: 12VDC, max 5A
• Teplotní senzor: 0-125℃/32-257℉, NTC3950, Accuracy: ±1℃/±1℉, Thread: M8
• Max Total Volume: 999999 G/L
• Quantitative Range: 0-9999.99 G/L
• Rozsah průtoku: 0-9999.99 LPM (GPM)
• Délka kabelu: 1m
• Rozměry: 88 mm x 126 mm x 30 mm
• Hmotnost: 200 g
• Provozní prostředí: Temperature: 0-50℃/32-122℉; Relative Humidity: <85%

G3/4" Flow Sensor

• Frekvence: F=5.5 * Q (L / Min)
• Rozsah průtoku: 1-60 l/min
• Allowable Compression: Water pressure 1.75 Mpa below
• Typ senzoru: Hallův efekt
• Délka kabelu: 15 cm
• Chyba: ± 2 %

G3/4" Solenoid Valve

• Pracovní tlak: 0.02-0.8 MPa

Nastavení a instalace

Proper installation is crucial for accurate operation. Follow these steps:

1. Umístění komponent: Properly install the flow sensor and solenoid valve in the water line. Ensure the flow sensor and solenoid valve direction aligns with the water flow direction. An arrow on the flow sensor indicates the correct flow path.
2. Zapojení: Connect the flow sensor, solenoid valve, and temperature sensor to the DFC15 controller according to the wiring diagram. Connect the 12VDC power adapter to the controller.
3. Počáteční nastavení: Before operation, set the K value, quantitative value, and maximum alarm value on the DFC15 controller. Refer to the operating instructions for details on setting these parameters.
4. Ohledy na životní prostředí: Avoid exposing the controller to water or excessive humidity to prevent damage.

A schematic diagram illustrating the wiring connections for the DIGITEN DFC15 controller, power adapter, solenoid valve, temperature sensor, and flow sensor, along with their placement in the water line.

An illustrative diagram showing a typical installation of the DIGITEN water flow control system, with the controller, solenoid valve, and flow sensor integrated into a water pipe.

The G3/4 inch water flow sensor, highlighting the arrow indicating the correct direction of water flow for proper installation.

Návod k obsluze

Once the system is installed and initial settings are configured, follow these steps for operation:

1. Zahájení provozu: Stiskněte tlačítko RUN / STOP button to initiate the control process. The controller will begin displaying the current flow volume, current flow rate, and the faucet animation will start.
2. Quantitative Control: The controller will automatically turn off the solenoid valve when the total flow reaches the pre-set quantitative value. At this point, the total value display will stop, the faucet animation will cease, and the flow rate will return to zero.
3. Repeat Operation: To repeat the same job, press the RUN / STOP znovu tlačítko.

The DIGITEN DFC15 LCD display controller, illustrating its dimensions and button layout for operation.

Údržba

To ensure the longevity and proper functioning of your DIGITEN DFC15 Water Flow Control System, observe the following maintenance guidelines:

• Protect the Controller: Always avoid direct contact of the controller with water or other liquids. Ensure it is installed in a dry environment.
• Pravidelná kontrola: Pravidelně kontrolujte všechna spojení, zda jsou pevná a zda nevykazují známky opotřebení.
• Čištění: Clean the exterior of the controller with a soft, dry cloth. Do not use abrasive cleaners or solvents.

Odstraňování problémů

If you encounter issues with your DIGITEN DFC15 Water Flow Control System, consider the following:

• Solenoid Valve Not Actuating: If you are using a solenoid valve that requires more than 2A, ensure you are using a suitable power adapter capable of supplying up to 5A. The included power adapter is rated for a maximum of 2A.
• Nepřesné údaje o průtoku: Verify that the flow sensor is installed correctly with the water flow direction matching the arrow on the sensor. Check for any blockages in the flow path.
• Ovladač se nezapíná: Ensure the 12VDC power adapter is securely connected to both the controller and a functional power outlet.

Záruka

The DIGITEN DFC15 Water Flow Control System comes with a Záruka 12 měsíců od data nákupu, která se vztahuje na výrobní vady. Uschovejte si prosím doklad o koupi pro případné reklamace.

Podpora

For further assistance, technical support, or warranty inquiries regarding your DIGITEN DFC15 Water Flow Control System, please contact DIGITEN customer service through their official channels.