1. Úvod
This manual provides essential information for the safe and efficient operation, installation, and maintenance of the Danfoss RT-112 Manual Pressure Switch. The RT-112 is designed for industrial applications, including boiler, air, water, and oil systems, to monitor and control pressure.
Obrázek 1: Přední strana view of the Danfoss RT-112 Manual Pressure Switch, showing the main housing and pressure connection.
2. Bezpečnostní informace
Always adhere to local regulations and safety standards when installing, operating, or maintaining the pressure switch. Failure to do so may result in injury or damage to equipment.
- Ensure power is disconnected before any installation or maintenance work.
- Instalaci a zapojení by měl provádět pouze kvalifikovaný personál.
- Verify the pressure switch ratings match the system requirements.
- Protect the device from excessive vibration, moisture, and extreme temperatures.
3. Nastavení a instalace
The Danfoss RT-112 is designed for panel mounting and features a screwed connector for pressure lines.
3.1 Montáž
Mount the pressure switch securely to a panel using appropriate fasteners. Ensure the mounting surface is stable and free from excessive vibration.
Figure 2: The Danfoss RT-112 pressure switch shown with included mounting hardware, including screws and washers.
3.2 Tlaková přípojka
Connect the pressure line to the 3/8" screwed connector at the bottom of the unit. Use appropriate sealing tape or compound to ensure a leak-free connection.
Obrázek 3: Detailní view of the 3/8" pressure connection, which is a standard threaded fitting for pressure lines.
3.3 Elektrické zapojení
The RT-112 features a Normally Open (NO) contact type and SPDT terminal. Refer to the internal wiring diagram and electrical specifications before connecting to the power supply. Ensure the power source matches the switch's current rating (10 Ampano, 3 Amps) a svtage požadavky.
Obrázek 4: Vnitřní view of the pressure switch, displaying the electrical terminals, pressure adjustment scales, and internal components.
Obrázek 5: Strana view of the pressure switch, highlighting the label with electrical ratings and certifications.
4. Návod k obsluze
The Danfoss RT-112 is a manual pressure switch, requiring manual adjustment for its setpoint and differential.
4.1 Setting Pressure Setpoint
To adjust the pressure setpoint, remove the cover and locate the adjustment knob. Rotate the knob to align the desired pressure value with the indicator. The internal scale provides readings in bar, psig, kg/cm², and kPa.
Obrázek 6: Nahoře view of the pressure switch, showing the manual adjustment knob used to set the pressure threshold.
4.2 Setting Differential
The differential setting determines the pressure difference between the cut-in and cut-out points. Adjust this setting as required for your application, typically found near the main setpoint adjustment.
5. Údržba
The Danfoss RT-112 is designed for minimal maintenance. Regular inspections are recommended to ensure optimal performance and longevity.
- Vizuální kontrola: Periodically check for any signs of physical damage, corrosion, or leaks around the pressure connection.
- Integrita připojení: Ensure all electrical and pressure connections remain tight and secure.
- Čištění: Keep the exterior of the unit clean and free from dust or debris. Do not use abrasive cleaners.
- Kontrola kalibrace: If precise pressure control is critical, periodically verify the switch's setpoint accuracy using a calibrated pressure gauge.
6. Řešení problémů
This section provides guidance for common issues encountered with the Danfoss RT-112 pressure switch.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Switch does not activate at setpoint | Incorrect setpoint; wiring issue; pressure not reaching setpoint; clogged pressure line | Verify setpoint; check wiring connections; confirm system pressure; inspect pressure line for obstructions. |
| Switch activates erratically | Vibration; pressure fluctuations; faulty switch | Reduce vibration; stabilize pressure; replace switch if faulty. |
| Leak at pressure connection | Improper sealing; damaged threads | Re-apply sealing tape/compound; inspect threads for damage. |
7. Technické specifikace
| Atribut | Hodnota |
|---|---|
| Značka | Danfoss |
| Model | RT-112 |
| Provozní režim | Manuál |
| Aktuální hodnocení | 10 Ampano, 3 Amps |
| Typ kontaktu | Normálně otevřeno |
| Typ konektoru | Šroubovaný |
| Terminál | Spdt |
| Typ obvodu | 2-cestný |
| Typ montáže | Montáž na panel |
| Typ pohonu | Závěsová páka |
| Kontaktní materiál | Měď |
| Rozměry balení | 9 x 4.5 x 3 palce |
| Hmotnost | 3.3 libry |
| Datum první dostupnosti | 29. ledna 2020 |
Figure 7: Common industrial applications for the Danfoss RT-112 pressure switch, including HVAC, turbines, heavy engineering, and air conditioning systems.
8. Záruka a podpora
For warranty information and technical support, please contact Danfoss customer service or visit the official Danfoss webmísto. Uschovejte si doklad o koupi pro případ záručních reklamací.
Protection plans may be available for extended coverage. Refer to your purchase details for more information on available protection plans.
Pro další pomoc můžete navštívit Obchod Danfoss na Amazonu.
