WilTec 20-Ton Hydraulic Shop Press with Manometer (Model 61978) - User Manual

1. Konec produktuview

The WilTec 20-Ton Hydraulic Shop Press (Model 61978) is designed for various pressing, bending, and crushing operations in professional and home workshop environments. Constructed from high-quality alloy steel, this robust frame press features an integrated manometer for precise pressure control and adjustable working height to accommodate different materials and project requirements. Its versatile design makes it suitable for industrial, agricultural, and craft applications.

Figure 1: The WilTec 20-Ton Hydraulic Shop Press, showcasing its robust red frame and integrated components in a workshop environment.

Obrázek 2: Přamples of typical applications for the hydraulic press, including automotive repair, general garage use, workshops, and industrial factory settings.

2. Bezpečnostní pokyny

Read and understand all safety warnings and instructions before operating this hydraulic press. Failure to follow these instructions may result in serious injury or property damage.

Obecná bezpečnostní opatření:

• Always wear appropriate Personal Protective Equipment (PPE), including safety glasses, gloves, and sturdy footwear.
• Ensure the press is placed on a firm, level, and stable surface capable of supporting its weight and the maximum pressing force.
• Nikdy nepřekračujte jmenovitou nosnost 20 tun.
• Do not work under the lifted load without additional support devices.
• Keep hands and other body parts clear of the pressing area during operation.
• Inspect the press for any signs of damage or structural weakness before each use. Do not operate a damaged press.
• Ujistěte se, že všechny šrouby a upevňovací prvky jsou bezpečně utažené.
• Do not use the press to compress springs or any other items that could suddenly release energy or be ejected from the press, causing a hazard.
• Udržujte děti a nepovolané osoby mimo pracovní oblast.
• Release pressure slowly and carefully after each operation.

3. Montáž

The WilTec 20-Ton Hydraulic Shop Press requires assembly. It is recommended to have at least two people for safe assembly due to the weight and size of the components. Refer to the included assembly diagram for detailed component identification and placement.

Montážní kroky:

1. Rozbalte komponenty: Opatrně vyjměte všechny díly z obalu a zkontrolujte je podle seznamu dílů.
2. Sestavte rám: Attach the base supports to the vertical frame pillars using the provided bolts and nuts. Ensure all connections are secure.
3. Install the Crossbeams: Mount the adjustable crossbeams onto the vertical pillars. These beams allow for height adjustment of the work surface.
4. Mount the Hydraulic Jack: Secure the 20-ton hydraulic jack to the top crossbeam. Ensure the jack is properly seated and fastened.
5. Attach the Manometer: Connect the manometer to the hydraulic jack as per the instructions to monitor pressure.
6. Install Support Jaws: Place the support jaws onto the adjustable crossbeams. These are used to hold the workpiece.
7. Závěrečná kontrola: Double-check all connections for tightness and ensure the press is stable before first use.

Obrázek 3: Detail view of the press base assembly, showing the sturdy feet and connecting frame components.

4. Nastavení pro provoz

Proper setup is essential for safe and effective operation.

• Pracovní oblast: Ujistěte se, že vaše pracovní místo je čisté, dobře osvětlené a bez překážek.
• Stabilita: Confirm the press is on a stable, level surface. For added stability, consider bolting the press to the floor if it will be used frequently for heavy tasks.
• Adjust Working Height: Adjust the height of the lower crossbeams to suit your workpiece. This is done by removing the pins, repositioning the beams, and reinserting the pins securely.
• Poloha obrobku: Place the workpiece centrally on the support jaws. Ensure it is stable and will not shift during pressing.
• Zkontrolujte hydraulickou kapalinu: Verify the hydraulic jack has sufficient fluid. Refer to the jack's specific instructions for checking and refilling.

Figure 4: Top section of the press showing the hydraulic jack and the integrated manometer for pressure monitoring.

5. Návod k obsluze

Follow these steps for safe and effective operation of your hydraulic press.

Pressing Procedure:

1. Připravte obrobek: Ensure the item to be pressed is clean and properly positioned on the support jaws.
2. Zavřete vypouštěcí ventil: Close the release valve on the hydraulic jack by turning it clockwise until it is tight.
3. Aplikujte tlak: Insert the pump handle into the jack's socket and pump slowly to raise the ram. Observe the manometer to monitor the applied pressure.
4. Monitor Workpiece: Continuously observe the workpiece during pressing. If any unusual sounds or movements occur, immediately stop and assess the situation.
5. Uvolňovací tlak: Once the operation is complete, slowly open the release valve by turning it counter-clockwise. The ram will retract.
6. Odstranění obrobku: Carefully remove the pressed item from the support jaws.

Videoukázka:

6. Údržba

Regular maintenance ensures the longevity and safe operation of your hydraulic press.

• Čištění: Keep the press clean and free from dirt, grease, and debris. Wipe down surfaces after each use.
• Mazání: Periodically lubricate moving parts, such as the ram and pivot points, with appropriate grease or oil.
• Hydraulická kapalina: Check the hydraulic fluid level regularly and top up if necessary. Use only recommended hydraulic fluid. Replace fluid according to manufacturer guidelines or if it appears contaminated.
• Inspekce: Regularly inspect all components for wear, damage, or loose fasteners. Pay close attention to welds, frame integrity, and the hydraulic jack.
• Skladování: Store the press in a dry, clean environment when not in use. Lower the ram completely to prevent corrosion of the piston.

7. Řešení problémů

This section addresses common issues you might encounter with your hydraulic press.

8. Technické specifikace

Key technical details for the WilTec 20-Ton Hydraulic Shop Press (Model 61978).

• Model: 61978
• Značka: WilTec
• Typ: Hydraulický dílenský lis
• Lisovací síla: 20 tun
• Materiál: Legovaná ocel
• Barva: Červený
• Rozměry (D x Š x V): 680 x 600 x 1500 mm (cca 68 x 60 x 150 cm)
• Hmotnost: 66.04 kg
• Vlastnosti: Integrated Manometer, Adjustable Working Height

Figure 5: Detailed dimensional drawing of the hydraulic press, showing key measurements for length, width, and height.

Figure 6: Technical drawing illustrating various dimensions and components of the hydraulic press, including working area and overall size.

9. Záruka a podpora

WilTec products are designed for durability and performance. For specific warranty information, please refer to the warranty card included with your product or visit the official WilTec website. In case of technical issues, missing parts, or warranty claims, please contact WilTec customer support directly. Keep your proof of purchase for all warranty-related inquiries.

Kontaktní údaje:

• Výrobce: WilTec Wildanger Technik GmbH
• Webmísto: www.wiltec.de (or refer to local distributor webweb)
• Služby zákazníkům: Kontaktní údaje naleznete na obalu produktu nebo na oficiálních webmísto.