1. Úvod
Welcome to the instruction manual for your Sygonix SY-RSL-T3 Wireless Wall Switch. This manual provides essential information for the safe and efficient use of your device. Please read it thoroughly before installation and operation, and keep it for future reference.
2. Bezpečnostní pokyny
Vždy dodržujte následující bezpečnostní opatření, abyste předešli zranění nebo poškození zařízení:
- Neotevírejte zařízení casing. Uvnitř nejsou žádné součásti, které by mohl uživatel opravit.
- Keep the device away from moisture, water, and extreme temperatures.
- Use only the specified battery type (12V, not included) and ensure correct polarity during installation.
- Použité baterie zlikvidujte v souladu s místními předpisy. Nevyhazujte baterie do domovního odpadu.
- This device is designed for indoor use. If used outdoors, ensure it is protected from direct weather exposure.
- Uchovávejte obalové materiály mimo dosah dětí.
3. Konec produktuview
3.1. Součásti
The Sygonix SY-RSL-T3 Wireless Wall Switch consists of the following main components:
- Wireless Wall Switch Unit (1 piece)
- Mounting Hardware (screws, if included with purchase)
This image shows the front of the Sygonix SY-RSL-T3 wireless wall switch. It is white with two large push-buttons. The left button is marked with an 'I' (for ON) and a circle (for OFF), and the right button is similarly marked. The switch has a slightly curved, modern design.
3.2. Vlastnosti
- Surface-mounted RSL wall switch
- Maximum wireless range: 70 meters (in open field)
- Push-button style operation (ON-OFF mode)
- Requires 12V battery (not included)
- Materiál: Plast
4. Nastavení a instalace
4.1. Vybalování
Opatrně vyjměte všechny součásti z obalu. Ujistěte se, že jsou všechny součásti přítomny a nepoškozené. Uschovejte si obal pro budoucí přepravu nebo skladování.
4.2. Instalace baterie
The device requires a 12V battery (not included). To install the battery:
- Vyhledejte přihrádku na baterie na zadní straně spínače.
- Otevřete kryt bateriového prostoru.
- Insert the 12V battery, ensuring correct polarity (+ and - terminals match the markings).
- Bezpečně zavřete kryt bateriového prostoru.
4.3. Mounting the Wall Switch
The SY-RSL-T3 is a surface-mounted switch. Choose a suitable, flat location for installation, free from excessive moisture or heat. Use appropriate screws or adhesive (not specified if included) to secure the switch to the wall. Ensure the mounting surface is clean and dry before installation.
Úhlové view of the white Sygonix SY-RSL-T3 wireless wall switch, highlighting its two push-buttons and sleek profile.
Strana view of the Sygonix SY-RSL-T3 wireless wall switch, showing its depth and how it would sit on a surface.
5. Návod k obsluze
5.1. Pairing with an RSL Receiver
To operate the switch, it must first be paired with a compatible Sygonix RSL receiver (sold separately). The SY-RSL-T3 uses the RSL wireless protocol.
- Refer to your RSL receiver's instruction manual for specific pairing instructions.
- Typically, you will need to put the RSL receiver into a pairing or learning mode.
- Within the specified time frame (usually a few seconds), press one of the buttons (e.g., 'I' or 'O') on the SY-RSL-T3 wall switch.
- The receiver should indicate successful pairing (e.g., by flashing an LED or clicking).
- Repeat the process if you wish to pair the other button to a different receiver or channel, if supported by your receiver.
5.2. Základní obsluha
Once successfully paired with an RSL receiver:
- Press the button marked with 'I' to send an ON signal to the paired receiver.
- Press the button marked with 'O' to send an OFF signal to the paired receiver.
The switch operates in a simple ON-OFF mode, controlling the connected device via the RSL receiver.
6. Údržba
6.1. Čištění
Clean the surface of the switch with a soft, dry, lint-free cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the plastic surface.
6.2. Výměna baterie
When the switch's wireless range decreases significantly, or it stops responding to button presses, the battery may need replacement. Follow the steps in section 4.2 (Battery Installation) to replace the 12V battery.
7. Řešení problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Zařízení nereaguje na stisknutí tlačítek. | Vybitá nebo slabá baterie. Není spárováno s přijímačem. Receiver is out of range or not powered. | Vyměňte 12V baterii. Perform the pairing procedure (see section 5.1). Ensure the RSL receiver is powered and within the 70m range. |
| Reduced wireless range. | Slabá baterie. Obstructions between switch and receiver. | Vyměňte 12V baterii. Minimize physical obstructions (e.g., thick walls, metal objects) between the switch and the receiver. |
8. Specifikace
| Funkce | Detail |
|---|---|
| Výrobce | Sygonix |
| Číslo modelu | SY-3523488 |
| Rozměry produktu (D x Š x V) | 1.9 × 8 × 8 cm (19 × 80 × 80 mm) |
| Hmotnost | 100 gramů |
| Materiál | Plast |
| Zdroj napájení | Napájení z baterie |
| Je vyžadována baterie | Yes (12 Volts, not included) |
| Styl přepínání | Tlačítko |
| Provozní režim | ZAPNUTO VYPNUTO |
| Aktuální hodnocení | 1 A |
| Bezdrátový protokol | RSL |
| Max. Range (open field) | 70 metrů |
| Množství v balení | 1 jednotka |
| Spare Parts Availability (EU) | 1 rok |
9. Záruka a podpora
Sygonix provides a 1-year warranty for spare parts availability within the EU. For further support, technical assistance, or warranty claims, please contact your retailer or Sygonix customer service. Please have your model number (SY-3523488) and ASIN (B07NLBNPTF) ready when contacting support.
Výrobce: Sygonix
Číslo modelu: SY-3523488
ASIN: B07NLBNPTF
