Návod k obsluze nástěnného ventilátorového ohřívače Stelpro Pulsair RWF0502W

Důležité bezpečnostní pokyny

Před instalací nebo použitím tohoto ohřívače si přečtěte všechny pokyny. Nedodržení těchto pokynů může vést k požáru, úrazu elektrickým proudem, vážnému zranění nebo smrti.

• Elektrické připojení: This heater operates on 240 Volts. All wiring must be performed by a qualified electrician and comply with national and local electrical codes.
• Základy: Tento ohřívač musí být uzemněn.
• Umístění: Do not install the heater near flammable materials, in areas where gasoline, paint, or other flammable liquids are stored, or where explosive dust is present. Maintain minimum clearances from walls and other objects as specified in the installation section.
• Dozor: Pečlivý dohled je nutný, pokud je jakýkoli ohřívač používán dětmi nebo osobami se zdravotním postižením, nebo v jejich blízkosti, a kdykoli je ohřívač ponechán v provozu bez dozoru.
• Přehřívání: To avoid overheating, do not cover the heater. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
• Údržba: Disconnect power at the main service panel before performing any maintenance or cleaning.
• Termostat: A separate thermostat is required for operation and is sold separately. Ensure the thermostat is compatible with a fan-forced heater.

Konec produktuview

The Stelpro pulsair RWF0502W is a 240V wall-mounted fan heater designed for supplemental heating in various rooms such as bedrooms, home offices, and living rooms. It utilizes both convection and forced air heating methods to efficiently distribute warmth.

Přední view of the Stelpro pulsair RWF0502W wall fan heater, showing the fan grille and lower air outlet.

Diagram showing the dimensions of the Stelpro pulsair RWF0502W wall fan heater: 17 1/8 inches (435 mm) height, 8 11/16 inches (220 mm) width, and 3 3/16 inches (80 mm) depth.

Instalace

Kontrolní seznam před instalací:

• Ujistěte se, že je hlavní jistič odpojen od napájení.
• Ověřte, že zásoba objtage matches the heater's rating (240V).
• Confirm you have a compatible wall thermostat (sold separately).
• Připravte si potřebné nástroje: šroubovák, odizolovací kleště, vrtačku, vodováhu, krejčovský metr.

Možnosti montáže:

The RWF0502W heater can be either surface-mounted directly to the wall or recessed into the wall for a flush finish. Ensure adequate clearance from floors, ceilings, and adjacent walls as per local codes and manufacturer recommendations.

The Stelpro pulsair RWF0502W wall fan heater installed in a modern entryway, positioned below a plant and mirror.

The Stelpro pulsair RWF0502W wall fan heater installed on a blue wall in an entryway, with coats and shoes nearby.

Elektrické připojení:

This heater requires a 240V hardwired connection. Follow the wiring diagram provided and ensure all connections are secure and properly insulated. Connect the heater to a dedicated circuit protected by the appropriate circuit breaker.

Diagram illustrating the 240V hardwired connection for the Stelpro pulsair RWF0502W wall fan heater, showing wires connecting within a junction box.

1. Turn off power at the main electrical panel.
2. Remove the front grille of the heater to access the wiring compartment.
3. Connect the supply wires to the heater's terminals according to the wiring diagram. Ensure proper grounding.
4. Secure all connections with wire nuts and ensure no bare wires are exposed.
5. Reattach the front grille.
6. Install the external wall thermostat according to its manufacturer's instructions.

Operace

The Stelpro pulsair RWF0502W heater is controlled by an external wall thermostat (not included). Once installed and wired correctly, follow these steps:

1. Zapnutí: Restore power to the heater circuit at the main electrical panel.
2. Nastavení termostatu: Adjust the external thermostat to your desired temperature. The heater will activate when the room temperature falls below the set point.
3. Počáteční provoz: During the first few minutes of operation, the heater may emit a slight odor due to the burning off of manufacturing residues. This is normal and will dissipate quickly.
4. Rozsah teplot: The heater is designed to operate within a temperature range of 5°C (41°F) to 30°C (86°F).

For optimal performance, avoid placing furniture or other obstructions directly in front of the heater's air outlets.

Údržba

Regular maintenance ensures efficient and safe operation of your Stelpro pulsair heater. Always disconnect power at the main circuit breaker before performing any maintenance.

• Čištění:
  • Otřete vnější část topení měkkým hadříkemamp tkanina. Nepoužívejte abrazivní čisticí prostředky nebo rozpouštědla.
  • Pravidelně vysávejte mřížky sání a výfuku vzduchu, abyste odstranili prach a usazeniny.
• Inspekce: Annually inspect the heater for any signs of damage, loose connections, or unusual wear. If any issues are found, contact a qualified electrician for repair.
• Bez mazání: The motor is permanently lubricated and requires no additional oiling.

Odstraňování problémů

If your Stelpro pulsair heater is not operating correctly, consult the following table before contacting customer support.

Specifikace

Záruka

Stelpro products are manufactured to high standards and are covered by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Stelpro webUschovejte si doklad o koupi pro případ reklamace.

Zákaznická podpora

For technical assistance, replacement parts, or further inquiries, please contact Stelpro customer service. Contact information can typically be found on the product packaging, the official Stelpro website, or by referring to the documentation included with your purchase.

Note: Always provide your product model number (RWF0502W) when contacting support.