1. Nastavení
This section guides you through the initial setup and installation of your Bontrager Ridetime Bike Computer.
1.1 Vybalení a identifikace součástí
Carefully unpack all components from the box. Verify that all parts are present:
- Bontrager Ridetime Bike Computer unit
- Handlebar/Stem mounting bracket
- Analog speed sensor
- Paprskový magnet
- CR2032 battery (for sensor, may be pre-installed)
- Zip ties for mounting
Obrázek 1: The Bontrager Ridetime Bike Computer shown with all its included components, including the main computer unit, handlebar mount, analog speed sensor, spoke magnet, and zip ties for installation.
1.2 Montáž počítače
- Attach the mounting bracket to your bicycle's handlebar or stem using the provided zip ties. Ensure it is securely fastened and positioned for easy viewIng.
- Slide the Bontrager Ridetime computer unit onto the mounting bracket until it clicks into place.
1.3 Installing the Speed Sensor and Spoke Magnet
- Mount the analog speed sensor to the front fork of your bicycle using the provided zip ties. Position it so that the sensor's alignment mark faces the wheel's spokes.
- Attach the spoke magnet to a spoke on your front wheel. Ensure the magnet is aligned with the sensor's alignment mark and passes within 5mm of the sensor with each wheel rotation. Adjust the sensor or magnet position as needed to achieve proper alignment and clearance.
- Confirm the sensor battery (CR2032) is installed. The sensor will activate when the magnet passes it.
2. Návod k obsluze
Learn how to use your Bontrager Ridetime Bike Computer to track your rides.
2.1 Zobrazení nadview
The large, clear display shows key ride metrics. The top section typically displays your current speed, while the bottom section shows the timer or other selected data.
Obrázek 2: Detailní záběr view of the Bontrager Ridetime Bike Computer's display, showing a large digital speed reading at the top and a timer function below it. A single button is visible at the bottom of the unit.
2.2 Funkce tlačítek
The Bontrager Ridetime computer features a single button for operation, located at the bottom of the unit.
- Krátký tisk: Cycles through various display modes (e.g., current speed, average speed, maximum speed, trip distance, total distance, timer).
- Dlouhé stisknutí: Resets trip data (trip distance, average speed, maximum speed, timer). Hold the button until the values reset to zero.
2.3 Initial Setup and Wheel Size
Before your first ride, ensure the correct wheel size is set for accurate speed and distance readings. Refer to the instructions that came with your computer for specific steps on entering wheel circumference, as this may vary by production batch. Typically, this involves a sequence of button presses during initial power-on or after a reset.
3. Údržba
Proper care ensures the longevity and accuracy of your bike computer.
3.1 Čištění
Otřete počítač a senzor měkkým hadříkemamp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla, protože by mohly poškodit displej neboasing. The unit has an IP54 international protection rating, meaning it is protected from dust ingress and splashing water from any direction. Avoid submerging the unit in water.
3.2 Výměna baterie
The speed sensor uses a CR2032 coin cell battery. When the sensor's signal becomes intermittent or stops, it may be time to replace the battery.
- Locate the battery compartment on the speed sensor.
- Use a small coin or screwdriver to open the battery cover.
- Vyjměte starou baterii CR2032 a vložte novou, dbejte na správnou polaritu (+ stranou nahoru).
- Bezpečně zavřete kryt baterie.
The main computer unit typically has a long-lasting internal battery or a user-replaceable battery. Refer to the original packaging or manufacturer's website for specific instructions on replacing the main unit's battery if needed.
4. Řešení problémů
Běžné problémy a jejich řešení.
4.1 No Speed Reading or Intermittent Data
- Check Sensor-Magnet Alignment: Ensure the spoke magnet passes within 5mm of the speed sensor. Adjust their positions if necessary.
- Baterie senzoru: Replace the CR2032 battery in the speed sensor.
- Orientace senzoru: Verify the sensor is mounted correctly on the fork with its alignment mark facing the magnet.
4.2 Incorrect Speed or Distance Readings
- Nastavení velikosti kola: Confirm that the correct wheel circumference is programmed into the computer. An incorrect setting will lead to inaccurate data.
- Magnet Position: Ensure the magnet is securely fastened and not slipping on the spoke.
4.3 Displej nefunguje
- Baterie hlavní jednotky: If the main unit uses a replaceable battery, check and replace it if necessary.
- Resetovat: Try performing a full reset of the computer (refer to operating instructions for long press function, or look for a small reset button on the back).
5. Specifikace
| Funkce | Specifikace |
|---|---|
| Číslo modelu | 1438143873069-13706076454957 |
| UPC | 601479718313 |
| Velikost displeje | 2 palce |
| Typ snímače | Analog Speed Sensor |
| Zahrnuté komponenty | Computer unit, Bracket, Analog Sensor, CR2032 Battery (for sensor), Spoke Magnet |
| Hodnocení mezinárodní ochrany | IP54 (ochrana proti prachu, odolnost proti stříkající vodě) |
| Vstup lidského rozhraní | Tlačítka |
| Hmotnost položky | 10 g |
6. Záruka a podpora
6.1 Informace o záruce
For detailed warranty information regarding your Bontrager Ridetime Bike Computer, please refer to the warranty card included with your original purchase or visit the official Bontrager webZáruční podmínky se mohou lišit v závislosti na regionu a produktu.
6.2 Zákaznická podpora
If you encounter issues not covered in this manual or require further assistance, please contact Bontrager customer support through their official website or the contact information provided in your product packaging. When contacting support, please have your product model number (1438143873069-13706076454957) and UPC (601479718313) available.
