Zavedení
This instruction manual provides detailed guidance for the installation, operation, and maintenance of your Everbilt 1 Pair Frameless 35 mm 110-Degree Full Overlay Nickel Cabinet Hinges. Please read this manual thoroughly before beginning installation to ensure proper function and longevity of the product.
Bezpečnostní informace
Always wear appropriate personal protective equipment, such as safety glasses, when working with tools and hardware. Keep small parts away from children. Ensure all screws are securely fastened to prevent injury or damage to the cabinet door.
Obsah balení
Verify that all components are present before beginning installation. If any parts are missing or damaged, do not proceed with installation and contact customer support.
- 2 x Everbilt 35 mm 110-Degree Full Overlay Cabinet Hinges
- Mounting Screws (quantity may vary, typically 8-12 screws)
Image: Two Everbilt 35mm 110-degree full overlay cabinet hinges are shown alongside a small pile of mounting screws. The hinges are made of nickel-plated steel, with one hinge in an open position and the other in a closed position, demonstrating their design and included hardware.
Nastavení a instalace
These hinges are designed for frameless cabinets with a full overlay door application. A 35mm cup hole is required in the cabinet door for hinge cup insertion.
Požadované nástroje:
- Drill with 35mm Forstner bit
- Šroubovák s křížovou hlavou
- Měřicí páska nebo pravítko
- Tužka
Kroky instalace:
- Příprava dvířek skříňky: Mark the positions for the 35mm hinge cup holes on the inside of the cabinet door. Typically, these are 3-4 inches from the top and bottom edges. Drill the 35mm cup holes to the appropriate depth (usually 1/2 inch or 13mm), ensuring not to drill through the door face.
- Připevnění pantů ke dveřím: Insert the hinge cups into the drilled holes. Secure each hinge cup to the cabinet door using the provided small screws. Ensure the hinges are flush and straight.
- Prepare the Cabinet Frame/Side Panel: For full overlay applications on frameless cabinets, the hinge mounting plate attaches directly to the inside of the cabinet side panel. Measure and mark the corresponding screw hole positions on the cabinet side panel, aligning with the hinges attached to the door.
- Mount Door to Cabinet: Align the hinges with the marked positions on the cabinet side panel. Secure the hinge mounting plates to the cabinet using the provided larger screws.
- Nastavení dveří: These hinges offer 3-way adjustability (side-to-side, depth, and height) to ensure perfect door alignment.
- Seřízení ze strany na stranu: Use the screw closest to the cabinet edge to move the door left or right.
- Nastavení hloubky: Use the screw further from the cabinet edge to move the door in or out from the cabinet face.
- Nastavení výšky: Loosen the mounting screws slightly, adjust the door up or down, then re-tighten.
Image: A cross-sectional diagram illustrating a full overlay hinge. It shows how the cabinet door completely covers the cabinet frame when closed, with the hinge mechanism positioned between the door and the cabinet side panel, demonstrating the "Full Overlay" concept.
Image: A single Everbilt 35mm 110-degree full overlay cabinet hinge is displayed. The hinge is made of nickel-plated steel, showing its cup, arm, and mounting plate components, ready for installation.
Provozní
Once installed and adjusted, the Everbilt 110-Degree Full Overlay Hinges allow the cabinet door to open smoothly to a 110-degree angle. The hinges are designed for quiet operation and provide a full overlay appearance, meaning the door completely covers the cabinet opening and frame when closed.
Údržba
These hinges require minimal maintenance. Periodically check all mounting screws to ensure they remain tight. If the door alignment shifts over time, refer to the "Adjust the Door" section under "Setup and Installation" to re-align. Clean hinges with a soft, damp tkanina; vyhýbejte se abrazivním čisticím prostředkům.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Door not closing properly or sagging | Loose mounting screws or improper adjustment. | Tighten all mounting screws. Adjust side-to-side and height screws as needed. |
| Door rubbing against cabinet | Incorrect door alignment. | Use the side-to-side adjustment screw on the hinge to move the door away from the rubbing point. |
| Door not flush with cabinet face | Depth adjustment needed. | Adjust the depth screw on the hinge to pull the door closer to or push it further from the cabinet face. |
Specifikace
- Typ produktu: Frameless Cabinet Hinge
- Číslo modelu: HC11SFE-NP-CP
- Overlay Type: Full Overlay
- Úhel otevření: 110 stupňů
- Průměr šálku: 35 mm
- Dokončit: Poniklované
- Nastavitelnost: 3-Way (Side-to-side, Depth, Height)
- Materiál: Ocel
- Obsah balení: 2 Hinges, Mounting Screws
Záruka a podpora
For information regarding product warranty or technical support, please refer to the Everbilt official webnebo se obraťte na jejich zákaznický servis. Uschovejte si doklad o koupi pro případ reklamace.
Note: Specific warranty details are not provided in this manual.
