BENINCA to.GO 2 A Garage Opener Remote Control User Manual

1. Úvod

This user manual provides comprehensive instructions for the installation, operation, and maintenance of your BENINCA to.GO 2 A Garage Opener Remote Control. This device is designed to provide convenient and secure access to your garage or gate system. Please read this manual thoroughly before using the remote control to ensure proper function and safety.

The BENINCA to.GO 2 A remote utilizes Advanced Rolling Code (ARC) technology. ARC enhances security by employing a 128-bit transmitted code, which is a significant improvement over older 64-bit systems, providing maximum safety against unauthorized access.

2. Bezpečnostní informace

Vždy dodržujte následující bezpečnostní opatření, abyste předešli zranění nebo poškození:

• Uchovávejte dálkový ovladač mimo dosah dětí, abyste zabránili jeho nechtěnému spuštění.
• Do not operate the garage door or gate if people, pets, or objects are in the path of its movement.
• Ensure the remote control is not exposed to extreme temperatures, direct sunlight, or moisture.
• Do not attempt to disassemble or modify the remote control. This may void the warranty and cause malfunction.
• Staré baterie zlikvidujte zodpovědně v souladu s místními předpisy.

3. Konec produktuview

The BENINCA to.GO 2 A is a compact and durable two-button remote control designed for ease of use. It features two distinct buttons for controlling different functions or two separate garage doors/gates.

Obrázek 3.1: Přední strana view of the BENINCA to.GO 2 A remote control, showing its two white control buttons and the BENINCA logo at the bottom.

Obrázek 3.2: Úhlové view of the BENINCA to.GO 2 A remote control, highlighting its sleek design and button placement.

Komponenty:

• Ovládací tlačítka: Two distinct buttons for operation.
• LED indikátor: A small light that illuminates during transmission.
• Přihrádka na baterie: Located on the rear or side for battery access.

4. Technické specifikace

*ARC: Advanced Rolling Code, providing enhanced security with a 128-bit transmitted code.

5. Nastavení a programování

Programming the BENINCA to.GO 2 A remote control typically involves a process of pairing it with your existing BENINCA receiver unit. The exact steps may vary slightly depending on your specific garage door opener or gate system model. Always refer to your receiver's manual for detailed programming instructions.

General Programming Steps (Consult Receiver Manual for Specifics):

1. Příjemce přístupu: Locate the programming button on your BENINCA garage door opener or gate receiver unit. This button is often labeled "PROG", "MEMO", or "LEARN".
2. Aktivace režimu učení: Press and release the programming button on the receiver. The LED on the receiver should illuminate or flash, indicating it is in learning mode. This mode is usually active for a short period (e.g., 5-10 seconds).
3. Přenosový kód: While the receiver is in learning mode, press and hold the desired button on your new BENINCA to.GO 2 A remote control for 2-3 seconds. The LED on the remote should light up during transmission.
4. Potvrdit spárování: The receiver's LED should change its behavior (e.g., flash rapidly, turn off, or illuminate steadily) to confirm successful pairing. Release the button on the remote.
5. Testovací provoz: After programming, wait a few seconds, then press the programmed button on your remote control to test its operation. The garage door or gate should respond.
6. Další tlačítka programu (volitelné): If you wish to program the second button for another function or device, repeat steps 2-5, selecting the other button on the remote.

Poznámka: If programming is unsuccessful, ensure the remote is within range of the receiver and that the receiver is correctly in learning mode. Some systems may require multiple presses of the remote button during programming.

6. Návod k obsluze

Using your BENINCA to.GO 2 A remote control is straightforward once programmed:

• Otevření/zavření: Point the remote control towards your garage door or gate opener and press the programmed button firmly. The door/gate should begin to move.
• Zastavit: Press the same programmed button again while the door/gate is in motion to stop it.
• Rozsah: The effective operating range may vary depending on environmental factors, battery strength, and obstructions. For optimal performance, operate within a reasonable distance from the receiver.
• LED indikátor: The small LED on the remote will illuminate when a button is pressed, indicating that a signal is being transmitted. If the LED does not light up or is dim, the battery may need replacement.

7. Údržba

Výměna baterie:

The BENINCA to.GO 2 A remote control uses a 12V A23 battery. When the remote's range decreases significantly or the LED indicator becomes dim or fails to light up, it's time to replace the battery.

1. Locate the battery compartment. This is typically on the back or side of the remote, secured by a small screw or a snap-on cover.
2. Carefully open the compartment using a small screwdriver or by prying the cover open.
3. Remove the old A23 battery. Note its orientation (+/-).
4. Insert a new 12V A23 battery, ensuring correct polarity.
5. Bezpečně uzavřete přihrádku na baterie.
6. Test the remote control to ensure it functions correctly.

Čištění:

Dálkový ovladač čistěte měkkým, suchým hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla, protože by mohly poškodit ovladač.asing nebo vnitřních součástí.

8. Řešení problémů

9. Záruka a podpora

For warranty information or technical support regarding your BENINCA to.GO 2 A remote control, please contact the retailer or the manufacturer directly. Keep your proof of purchase for warranty claims.

For further assistance with programming or troubleshooting, it is recommended to consult the user manual of your specific BENINCA garage door opener or gate receiver unit, as programming procedures can vary.