1. Úvod
This manual provides comprehensive instructions for the safe and effective use of your TRU COMPONENTS 98001c411 White In-line Cord Switch. This switch is designed for integration into flexible power cords, allowing for convenient ON/OFF control of electrical devices. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.
2. Bezpečnostní pokyny
VAROVÁNÍ: Nebezpečí úrazu elektrickým proudem!
- Always disconnect power to the circuit before installing, servicing, or removing the switch. Failure to do so can result in serious injury or death.
- This product should only be installed by a qualified electrician or competent person familiar with electrical wiring and safety standards.
- Ensure the switch's electrical ratings (voltage and current) are compatible with the device and circuit it will control.
- Nepřekračujte maximální jmenovitý proud 2 Amperes.
- Nepoužívejte ve vlhkém nebo damp podmínky, pokud nejsou pro taková prostředí výslovně určeny.
- Inspect the switch and cord for any damage before installation and use. Do not use if damaged.
3. Obsah balení
Po otevření balení ověřte, zda jsou všechny součásti přítomny a nepoškozené:
- 1 x TRU COMPONENTS 98001c411 White In-line Cord Switch
Image 1: TRU COMPONENTS 98001c411 White In-line Cord Switch. This image shows the compact white switch with two rocker buttons for ON/OFF control, designed to be integrated into a power cord.
4. Nastavení a instalace
Professional installation is highly recommended for electrical components.
- Připravte si šňůru: Identify the power cord where the switch will be installed. Ensure the cord is unplugged from the power source. Carefully cut one of the two conductors (usually the live wire) of the cord at the desired switch location. Strip approximately 5-7mm of insulation from the ends of the cut wires.
- Open the Switch Housing: The switch housing typically consists of two halves. Gently pry them apart to expose the internal terminals.
- Připojit dráty: Insert the stripped ends of the power cord into the designated terminals within the switch. Ensure a secure connection by tightening the terminal screws. The switch is designed to interrupt one side of the circuit.
- Zajistěte kabel: Many in-line switches include a strain relief mechanism. Ensure the cord is properly secured within this mechanism to prevent accidental pulling on the wire connections.
- Zavřete kryt: Carefully reassemble the two halves of the switch housing, ensuring no wires are pinched and the housing snaps or screws securely together.
- Test: Once installed, plug the power cord back into the power source and test the switch functionality with the connected device.
5. Návod k obsluze
The TRU COMPONENTS 98001c411 In-line Cord Switch features a simple ON/OFF operation:
- Zapnout: Press the rocker button marked "ON" or the side that illuminates (if applicable) to allow power to flow to the connected device.
- Vypnout: Press the rocker button marked "OFF" or the opposite side to interrupt power to the connected device.
Ensure the switch is easily accessible for convenient operation.
6. Údržba
The TRU COMPONENTS 98001c411 In-line Cord Switch requires minimal maintenance:
- Čištění: Periodically wipe the exterior of the switch with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the switch is unplugged before cleaning.
- Inspekce: Regularly inspect the switch and the connected cord for any signs of damage, wear, or loose connections. If any damage is observed, discontinue use immediately and replace the switch.
7. Řešení problémů
If the device connected to the in-line switch is not functioning, consider the following:
- Bez napájení:
- Ensure the main power source is active and the cord is securely plugged into the wall outlet.
- Verify the switch is in the "ON" position.
- Check if the connected device itself is working by plugging it directly into a known working outlet.
- Uvolněná připojení: If you suspect loose internal wiring, disconnect power and carefully re-open the switch to check the wire terminals. If you are not comfortable doing this, consult a qualified electrician.
- Poškozený spínač: If the switch housing or buttons appear damaged, or if there is a burning smell, discontinue use immediately and replace the switch.
If issues persist, contact TRU COMPONENTS customer support or a qualified electrician.
8. Specifikace
| Funkce | Hodnota |
|---|---|
| Číslo modelu | 98001c411 |
| Značka | Komponenty TRU |
| Provozní režim | ZAPNUTO VYPNUTO |
| Aktuální hodnocení | 2 A |
| Provozní svtage | 250 voltů (AC) |
| Typ kontaktu | Normálně otevřeno |
| Typ přepínače | Teplotní spínač (Note: This classification may refer to a broader category; the product functions as an in-line cord switch.) |
| Typ terminálu | Spade or Through-hole |
| Materiál | Polykarbonát |
| Rozměry produktu (D x Š x V) | 32 x 35 x 35 mm |
| Typ obvodu | 1-cestný |
9. Podpora
For further assistance, technical support, or inquiries regarding your TRU COMPONENTS 98001c411 In-line Cord Switch, please contact TRU COMPONENTS customer service through their official webmístě nebo autorizovaným distributorům.
Please have your model number (98001c411) available when contacting support.
