Uživatelská příručka k dálkovému ovládání krbu s podsvícením Skytech 9800325 SKY-3301P2

Zavedení

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Skytech 9800325 SKY-3301P2 remote control system. This system is designed to offer safe, reliable, and user-friendly control for gas heating appliances. It supports both thermostatic and manual operation from the transmitter.

The system utilizes radio frequencies (RF) for communication within a 20-foot range, employing non-directional signals. Each system operates on one of 1,048,567 security codes, pre-programmed at the factory. It is essential to match the remote receiver's code to that of the transmitter before initial use.

Obsah balení

Upon unpacking, verify that all components are present and undamaged. The package should include:

• Transmitter (Remote Control Unit)
• Přijímací jednotka
• Wall Holder for Transmitter
• Nástěnná deska
• Pokyny k instalaci
• Batteries (2 AAA for transmitter, 4 AA for receiver)

Obrázek 1: Nadview of the Skytech 9800325 SKY-3301P2 remote control system, showing the handheld transmitter, the wall-mounted receiver, and the wired receiver box.

Nastavení a instalace

1. Instalace baterie

Vysílač: Open the battery compartment on the back of the transmitter and insert two (2) AAA batteries, observing the correct polarity. Close the compartment securely.

Přijímač: Open the battery compartment on the receiver unit and insert four (4) AA batteries, observing the correct polarity. Close the compartment securely.

2. Receiver Placement and Wiring

The receiver can be installed in the wall, on the hearth, or under the fireplace behind the control access panel. Ensure the receiver is placed in a location that allows for proper signal reception from the transmitter and is not exposed to excessive heat.

Connect the two wires from the receiver to the appropriate terminals on your gas heating appliance's control valve. Refer to your appliance's manual for specific wiring instructions. Ensure all connections are secure and properly insulated.

Obrázek 2: Close-up of the receiver unit, showing the 'OFF', 'REMOTE', 'ON' slider switch and 'LEARN' button. This unit connects to the fireplace.

3. Matching Security Codes (Learning Function)

The transmitter and receiver are factory-matched. However, if they lose synchronization or if you are replacing a component, you may need to re-match them:

1. Ensure batteries are installed in both the transmitter and receiver.
2. Locate the 'LEARN' button on the receiver unit.
3. Press and hold the 'LEARN' button on the receiver until you hear a series of beeps (approximately 1-2 seconds).
4. Within 10 seconds, press any button on the transmitter. The receiver will emit another series of beeps, confirming that the codes have been matched.

If the matching process fails, repeat the steps. Ensure the transmitter is within 20 feet of the receiver during this process.

Návod k obsluze

Ovládací prvky vysílače

Obrázek 3: Close-up of the handheld transmitter, showing the backlit LCD display with room temperature and set temperature, and the 'DOWN', 'MODE', 'UP' buttons. The flip cover conceals 'PROG' and 'SET' buttons.

• Tlačítko NAHORU: Zvyšuje nastavenou teplotu nebo prochází položky nabídky.
• Tlačítko DOLŮ: Snižuje nastavenou teplotu nebo prochází položky nabídky.
• Tlačítko MODE: Cycles through operating modes (ON, THERMO, OFF, PROGRAM).
• PROG Button (under flip cover): Used for programming thermostat schedules.
• SET Button (under flip cover): Used to confirm settings or enter programming mode.

Receiver Slider Switch

The receiver unit has a three-position slider switch:

• NA: Manually turns the appliance ON, bypassing remote control.
• DÁLKOVÝ: Allows the appliance to be controlled by the transmitter.
• OFF: Manually turns the appliance OFF, bypassing remote control.

For normal operation with the remote control, ensure the receiver switch is set to VZDÁLENÝ.

Provozní režimy

Stiskněte tlačítko MODE button on the transmitter to cycle through the following modes:

• NA: The appliance will turn on and remain on until switched off.
• TERMO: The appliance will operate based on the set temperature. When the room temperature falls below the set temperature, the appliance will turn on. When the room temperature rises above the set temperature, the appliance will turn off.
• OFF: The appliance will remain off.
• PROGRAM: The appliance will follow the programmed schedule for temperature control.

Setting the Temperature (THERMO Mode)

1. Stiskněte tlačítko MODE button until "THERMO" is displayed on the LCD.
2. Použijte UP or DOLŮ buttons to adjust the desired set temperature. The display will show both the current room temperature and the set temperature.

Programming a Schedule (PROGRAM Mode)

The 3301P2 allows for programmable temperature settings. Lift the flip cover on the transmitter to access the PROG a SOUBOR tlačítka.

1. Stiskněte tlačítko MODE button until "PROGRAM" is displayed on the LCD.
2. Stiskněte tlačítko PROG tlačítko pro vstup do programovacího režimu.
3. Použijte UP or DOLŮ buttons to adjust the time and temperature settings for each program period (P1, P2).
4. Stiskněte SOUBOR pro potvrzení každého nastavení a přechod k dalšímu.
5. The system typically allows for two program periods (P1 for morning/day, P2 for evening/night) with separate ON/OFF times and temperatures. Consult the detailed instructions provided with the product for specific programming steps, as these can be intricate.

Poznámka: The programming interface may require careful attention to detail. If you encounter difficulties, refer to the troubleshooting section or contact support.

Údržba

Výměna baterie

Replace batteries in both the transmitter and receiver when the low battery indicator appears on the transmitter's LCD, or if the remote control range decreases significantly. Use high-quality alkaline batteries for optimal performance.

• Vysílač: 2 x AAA baterie.
• Přijímač: 4 x AA baterie.

Always replace all batteries at the same time. Dispose of old batteries responsibly according to local regulations.

Čištění

Wipe the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

Odstraňování problémů

Specifikace

• Model: 9800325 (SKY-3301P2)
• Značka: SkyTech
• Rozměry produktu: 6.5 x 3.6 x 3 inches (Transmitter and Receiver combined, approximate)
• Hmotnost: 12.96 unce (přibližně)
• Výkon vysílače: 2 x AAA baterie
• Výkon přijímače: 4 x AA baterie
• Typ ovládání: Stiskněte tlačítko
• Speciální funkce: Programmable Thermostat, Backlit Display
• Bezdrátový dosah: Až 20 metrů (nesměrová RF)
• Bezpečnostní kódy: 1 048 567 unikátních kódů
• Specifická použití: Fireplace Control, Thermostat Control, Indoor Residential Environments

Záruka a podpora

For warranty information or technical support, please refer to the documentation included with your purchase or visit the official SkyTech webUschovejte si doklad o koupi pro případ reklamace.

Výrobce: Skytech

For further assistance, contact SkyTech customer service.