1. Úvod
This manual provides essential instructions for the proper installation, operation, and maintenance of the Norlake 139850S Dixel XR06 Programmed Controller. This device is designed for precise temperature control in commercial refrigeration applications. Please read this manual thoroughly before attempting to install or operate the controller to ensure safe and efficient performance.
2. Bezpečnostní informace
- Always disconnect power before performing any installation, wiring, or maintenance procedures.
- Installation and wiring should only be performed by qualified personnel in accordance with local and national electrical codes.
- Zajistěte napájení objtage matches the controller's specifications (120V, 50-60Hz).
- Nevystavujte regulátor vodě ani nadměrné vlhkosti.
- Use genuine OEM parts for safety, reliability, and performance.
3. Konec produktuview
The Norlake 139850S Dixel XR06 is a compact, programmed controller designed for refrigeration units. It features a digital display for temperature readings and status indicators, along with control buttons for setting parameters. The unit is supplied with a removable terminal block for electrical connections and mounting clips for secure installation.
Obrázek 1: Norlake 139850S Dixel XR06 Programmed Controller. This image displays the Norlake 139850S Dixel XR06 Programmed Controller unit, a green terminal block connector, and two white mounting clips. The controller features a digital display and control buttons on the front panel, with wiring diagrams and specifications printed on its side.
Součásti řídicí jednotky:
- Digitální displej: Zobrazuje aktuální teplotu a provozní stav.
- Ovládací tlačítka: Used for setting parameters and navigating menus (e.g., SET, Up, Down, Light/Aux).
- Svorkovnice: Removable connector for electrical wiring.
- Montážní klipy: For securing the controller in a panel cutout.
- Identifikační štítek: Located on the side, indicating model, voltage, frequency, probe type (NTC), and power consumption (3.3VA MAX).
4. Nastavení a instalace
4.1 Montáž
- Create a panel cutout of appropriate dimensions for the controller.
- Vložte ovladač do výřezu zepředu.
- Secure the controller using the provided mounting clips, ensuring a snug fit.
4.2 Zapojení
Refer to the wiring diagram printed on the side of the controller and the specific requirements of your refrigeration system. The terminal block connections typically include:
- Power Supply (120V, 50-60Hz): Connect to the designated 'Supply' terminals.
- Compressor (Comp): Connect to the compressor load terminals.
- Ventilátor: Connect to the fan load terminals.
- Defrost (Def): Connect to the defrost heater terminals.
- Probe (NTC): Connect the temperature sensor probe to the designated NTC probe terminals.
Poznámka: Ensure all connections are secure and correctly polarized. Incorrect wiring can damage the unit or pose a safety hazard.
5. Návod k obsluze
5.1 Počáteční zapnutí
Once wired and mounted, apply power to the controller. The display will illuminate, showing the current temperature measured by the NTC probe.
5.2 Setting the Temperature (Set Point)
- Stiskněte tlačítko SOUBOR button. The current set point temperature will flash on the display.
- Použijte Up a Dolů arrow buttons to adjust the set point to the desired temperature.
- Stiskněte tlačítko SOUBOR button again to confirm and save the new set point. The display will return to showing the current temperature.
5.3 Accessing Parameters (Hot Key)
Advanced parameters, such as defrost cycles, differential, and probe calibration, can be accessed through a specific sequence, often referred to as the 'Hot Key' function. Consult the detailed Dixel XR06 programming manual for specific parameter codes and adjustment procedures. This typically involves holding down certain buttons for a few seconds to enter the parameter menu.
6. Údržba
6.1 Čištění
- Wipe the controller's front panel with a soft, damp tkanina.
- Nepoužívejte abrazivní čisticí prostředky, rozpouštědla ani nadměrnou vlhkost, protože by mohly poškodit displej nebo vnitřní součásti.
6.2 Kontrola
- Pravidelně kontrolujte těsnost kabelových spojů a známky opotřebení nebo koroze.
- Ensure the temperature probe is securely in place and free from damage.
7. Řešení problémů
This section addresses common issues you might encounter with the controller.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Displej ovladače je vypnutý | No power supply; loose wiring | Check power connections and circuit breaker. Ensure wiring is secure. |
| Nesprávný údaj o teplotě | Faulty probe; probe not properly installed | Check probe connection. Replace probe if damaged. Verify probe type (NTC). |
| Compressor/Fan not operating | Incorrect set point; wiring issue; controller fault | Verify set point. Check wiring to compressor/fan. Consult a qualified technician if fault persists. |
| Kód chyby na displeji | Specifická systémová chyba | Refer to the Dixel XR06 programming manual for specific error code definitions and troubleshooting steps. |
8. Specifikace
- Číslo modelu: 139850S
- Značka: Norlake
- Typ ovladače: Programmed Controller (Dixel XR06)
- svtage: 120V
- Frekvence: 50-60Hz
- Typ sondy: NTC
- Spotřeba energie: 3.3VA MAX
- Provozní vlhkost: 20–85 % relativní vlhkosti (bez kondenzace)
- Approximate Unit Dimensions (based on package): 10 x 10 x 8 palce
- Přibližná hmotnost položky: 8 unce
- UPC: 046843096626
- Výrobce: Norlake
- Datum první dostupnosti: 10. října 2017
9. Záruka a podpora
The Norlake 139850S Dixel XR06 Programmed Controller is a genuine OEM (Original Equipment Manufacturer) replacement part. For specific warranty information, please refer to the terms provided by Norlake or your authorized distributor at the time of purchase. For technical support or service, contact your Norlake dealer or a qualified refrigeration technician.
