ThermoPro TP60 Remote Sensor Instruction Manual

1. Úvod

The ThermoPro TP60 Remote Sensor is designed to work with compatible ThermoPro base stations (such as TP60S, TP63A, and TP65) to provide accurate remote temperature and humidity readings. This sensor is suitable for both indoor and outdoor use, allowing you to monitor environmental conditions in various locations.

Obrázek 1.1: Přední strana view of the ThermoPro TP60 Remote Sensor, showing its compact design and wireless capabilities.

Image 1.2: The ThermoPro TP60 Remote Sensor shown with various compatible ThermoPro base units, illustrating its versatility.

2. Vlastnosti produktu

• Kompatibilita: Designed as an extension or replacement sensor for ThermoPro TP60S, TP63A, and TP65 base units.
• Rozšířený rozsah: Offers a transmission range of up to 200 feet (60 meters) in open areas. Actual range may vary based on environmental interference.
• Všestranné použití: Can be utilized as an indoor or outdoor sensor, and multiple sensors can be combined with a single base station to monitor various rooms or outdoor areas.
• Flexibilní umístění: Features a magnetic back for hanging and a foldable stand for tabletop placement.
• Vysoká přesnost: Provides precise temperature readings with an accuracy of ±2°F and humidity readings with an accuracy of ±2~3% relative humidity.
• Zdroj napájení: Vyžaduje 2 baterie AAA (součástí balení).

3. Obsah balení

• 1 x ThermoPro TP60 Remote Sensor (Transmitter)
• 2 x AAA baterie

4. Nastavení a instalace

4.1 Instalace baterie

1. Locate the battery compartment on the back of the remote sensor.
2. Slide down the battery cover to open it.
3. Vložte dvě baterie typu AAA a dbejte na správnou polaritu (+ a -).
4. Pevně ​​zavřete kryt baterie.

Obrázek 4.1: Zadní strana view of the remote sensor, highlighting the battery compartment, channel switch (1.2.3), RESET button, and TX button.

4.2 Výběr kanálu

The remote sensor features a channel switch (1, 2, 3) inside the battery compartment. If you are using multiple remote sensors, set each sensor to a different channel (e.g., Sensor 1 to CH1, Sensor 2 to CH2, Sensor 3 to CH3) to avoid interference and allow individual monitoring on your base station.

4.3 Synchronization with Base Station

To ensure proper communication, synchronize the remote sensor with your ThermoPro base station:

1. Position the remote sensor near the base station (within a few feet).
2. Ensure batteries are installed in both the remote sensor and the base station.
3. On the base station, the RF signal icon (usually located at the top left of the screen) should flash, indicating it is searching for a signal.
4. Wait a moment for the sensor to connect automatically, or press the TX button on the remote sensor to manually send a signal.
5. The temperature and humidity readings from the remote sensor should then appear on the base station display.

5. Provoz

Once synchronized, the remote sensor will continuously transmit temperature and humidity data to your base station. The base station will display these readings, often cycling through multiple channels if more than one sensor is connected. Refer to your base station's manual for specific display and channel selection instructions.

6. Pokyny pro umístění

Optimal placement of the remote sensor is crucial for accurate readings and reliable transmission:

• Přímé sluneční světlo: The remote sensor should NOT be placed in direct sunlight. Sunlight will heat the sensor, leading to higher temperature readings than the actual ambient air temperature.
• Orientace: Always place the remote sensor facing upwards. This prevents rain or moisture from entering the ventilation holes at the bottom of the sensor, ensuring accurate and faster detection of environmental temperature and humidity.
• Rušení: Avoid placing the sensor near sources of electromagnetic interference, such as large metal objects, electronic devices, or thick walls, which can reduce the transmission range.
• Rozsah teplot: The sensor is designed for outdoor use, with a minimum operating temperature of -4°F (-20°C).

Image 6.1: The remote sensor mounted outdoors in a cold environment, demonstrating its suitability for various weather conditions, with a note on minimum operating temperature.

7. Údržba

• Výměna baterie: Replace batteries when the low battery indicator appears on your base station. Always use fresh AAA batteries.
• Čištění: Otřete senzor měkkým hadříkemamp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani neponořujte jednotku do vody.
• Skladování: If storing the sensor for an extended period, remove the batteries to prevent leakage.

8. Řešení problémů

If you experience issues with your ThermoPro TP60 Remote Sensor, consider the following:

• No Readings or Intermittent Signal:
  • Ensure the remote sensor is within the 200-foot transmission range of the base station.
  • Check battery levels in both the sensor and base station. Replace if low.
  • Verify that the remote sensor's channel switch matches the selected channel on the base station.
  • Resynchronization: Try removing batteries from both the base station and the remote sensor. Reinsert batteries into the remote sensor (ensuring correct channel), then reinsert batteries into the base station. Press the CH/SYNC button on the base station to initiate a new synchronization. Keep the sensor close to the base station during this process.
  • Relocate the sensor or base station to minimize interference from other electronic devices or large metal objects.
• Nepřesné údaje o teplotě/vlhkosti:
  • Ensure the sensor is not in direct sunlight, which can artificially inflate temperature readings.
  • Verify the sensor is placed facing upwards to prevent moisture ingress.
  • Allow the sensor to stabilize for at least 30 minutes after placement or battery change, as readings may take time to adjust to the environment.

9. Specifikace

10. Záruka a podpora

ThermoPro provides customer support for its products. For warranty information, technical assistance, or any questions regarding your TP60 Remote Sensor, please refer to the official ThermoPro website or contact their customer service directly. Details are typically available on the product packaging or the main base station manual.