Hyundai HY6000 Gasoline Generator User Manual

3.1 Vybalení a kontrola

Carefully remove the generator from its packaging. Inspect for any damage that may have occurred during shipping. If any damage is found, contact your dealer immediately.

3.2 Umístění

Place the generator on a firm, level surface. Ensure there is adequate clearance around the unit for proper ventilation and to prevent heat buildup. Keep it at least 1 meter (3 feet) away from buildings or other equipment.

3.3 Doplnění motorového oleje

The generator is shipped without engine oil. Before first use, add the recommended engine oil (e.g., SAE 10W-30) to the crankcase. Refer to the oil fill cap or dipstick for the correct level. Do not overfill.

Obrázek 1: Strana view of the generator engine. The oil fill cap is typically located on the side of the engine block, often yellow or black, and may have a dipstick attached for checking oil level.

3.4 Doplnění paliva

Use fresh, unleaded gasoline with an octane rating of 87 or higher. Fill the fuel tank carefully, avoiding spills. Do not fill above the red indicator or the bottom of the filler neck. Securely close the fuel cap after filling.

• Always refuel in a well-ventilated outdoor area.
• Před doplňováním paliva se ujistěte, že je motor vypnutý a vychladlý.
• Do not smoke or use open flames near the generator.

3.5 Uzemnění generátoru

For safety, the generator must be properly grounded. Connect a heavy-gauge copper wire from the generator's grounding terminal to an earth ground rod or other approved grounding source. Consult local electrical codes for specific requirements.

4.1 Ovládací panel Overview

Obrázek 2: Přední view of the control panel. Features include two 16A AC outlets, a digital LED display for voltage/frequency/hours, a circuit breaker, and a DC 12V output with thermal protection.

Ovládací panel obsahuje:

• AC Outlets (2x 16A): For connecting 220V appliances. Equipped with overload protection.
• Digitální LED displej: Ukazuje svtage, frekvence a provozní hodiny.
• Jistič: Protects against overloads.
• DC 12V Output (8.3A): For charging 12V batteries, with thermal protection.
• Uzemňovací terminál: For connecting to an earth ground.
• LED indikátor: For overload or usage status.

4.2 Startování motoru (ruční start)

1. Ujistěte se, že generátor je na rovném povrchu a řádně uzemněn.
2. Zkontrolujte hladinu motorového oleje a paliva.
3. Otočte palivový ventil do polohy „ON“.
4. Přesuňte páčku sytiče do polohy „SYTIČ“ (pokud je motor studený).
5. Otočte spínač motoru do polohy „ON“.
6. Grasp the recoil starter handle firmly and pull it slowly until resistance is felt, then pull quickly and smoothly to start the engine.
7. Jakmile motor nastartuje, pomalu přesuňte páčku sytiče do polohy „RUN“.
8. Před připojením elektrických zátěží nechte motor několik minut zahřát.

Obrázek 3: Strana view of the generator, highlighting the manual recoil pull start handle, typically yellow or black, located on the engine's flywheel cover.

4.3 Připojení elektrických zátěží

After the engine has warmed up, you can connect your appliances. Ensure the total wattage of connected devices does not exceed the generator's rated output (4400W). Overloading the generator will trip the circuit breaker.

• Plug appliances directly into the AC outlets on the control panel.
• For 12V DC charging, connect the appropriate cables to the DC output.
• If the generator stops due to overload, reduce the load and reset the circuit breaker.

4.4 Zastavení motoru

1. Odpojte všechny elektrické zátěže od generátoru.
2. Otočte spínač motoru do polohy „VYPNUTO“.
3. Otočte palivový ventil do polohy „VYPNUTO“.

5.1 Plán údržby

5.2 Výměna motorového oleje

Drain the old oil while the engine is warm. Remove the oil drain plug and allow all oil to drain into a suitable container. Replace the drain plug and refill with the recommended amount and type of new engine oil.

5.3 Čištění vzduchového filtru

Remove the air filter cover and take out the foam filter element. Wash it in warm, soapy water, rinse thoroughly, and allow it to dry completely. Lightly oil the foam element with engine oil, squeeze out excess, and reinstall.

5.4 Kontrola zapalovací svíčky

Remove the spark plug and inspect its condition. Clean any carbon deposits with a wire brush. Check the gap with a feeler gauge and adjust if necessary. Replace if the electrode is worn or damaged.

5.5 Skladování

For long-term storage, drain the fuel tank and carburetor, or add a fuel stabilizer. Change the engine oil. Clean the generator thoroughly. Store in a clean, dry, well-ventilated area.