1. Úvod
This manual provides essential instructions for the proper installation, operation, and maintenance of the Protech 61-104025-15 Service Valve. Adhering to these guidelines will ensure safe and efficient performance of the valve. Please read this manual thoroughly before proceeding with any procedures.
2. Konec produktuview
The Protech 61-104025-15 Service Valve is a component designed for various industrial and plumbing applications, particularly within HVAC and refrigeration systems. It facilitates isolation and control of fluid flow, allowing for system servicing without complete depressurization or drainage. This valve is compatible with models such as raka, rakb, ralc, rama, ramb, ramc, ramm, ranc, rand, ranl, rapa, rapb, rapc, rapl, rapm, rara, rarl, rasl, rpka, rpkb, rpla, rplb, rpmb, rpmc, rpmd, rpmm, rpne, rpnk, rpnl, rppb, rppc, rppl, rpql, rprl, saka, sakb, spkb.
Obrázek 1: The Protech 61-104025-15 Service Valve. This image displays the brass-colored valve body, featuring two 3/4-inch sweat ODF connections on opposing sides and a hexagonal cap at the top for manual operation.
3. Nastavení a instalace
Installation of the Protech 61-104025-15 Service Valve requires careful attention to connection types and proper sealing techniques. It is recommended that installation be performed by a qualified technician.
3.1 Podrobnosti připojení
- Upper Connection Size: 3/4 palce
- Upper Connection Type: Sweat ODF (Outer Diameter Flare)
- Lower Connection Size: 3/4 palce
- Lower Connection Type: Sweat ODF (Outer Diameter Flare)
3.2 Postup instalace
- Bezpečnost především: Před zahájením instalace se ujistěte, že je systém bez tlaku a vypuštěn. Používejte vhodné osobní ochranné prostředky (OOP).
- Příprava připojení: Clean the ends of the pipes and the valve's sweat connections thoroughly to remove any dirt, grease, or oxidation. Apply appropriate flux to both surfaces.
- Umístění ventilu: Place the valve in the desired position, ensuring proper alignment with the piping.
- Pájené spoje: Using a suitable heat source and solder, create strong, leak-free sweat joints. Allow the joints to cool naturally.
- Test těsnosti: After installation, pressurize the system and carefully check all connections for leaks using an approved leak detection method.
4. Provoz
The Protech 61-104025-15 Service Valve is designed for straightforward manual operation to control or isolate fluid flow within a system.
4.1 Opening and Closing the Valve
- Na OTEVŘENO the valve, turn the hexagonal cap counter-clockwise until the desired flow is achieved or the valve is fully open.
- Na blízko the valve, turn the hexagonal cap clockwise until the valve is fully closed and flow is stopped. Do not overtighten.
Always operate the valve smoothly and avoid sudden, forceful movements to prevent damage to the valve or system components.
5. Údržba
Regular maintenance ensures the longevity and reliable performance of your Protech 61-104025-15 Service Valve.
- Pravidelná prohlídka: Visually inspect the valve and its connections regularly for any signs of wear, corrosion, or leaks.
- Čištění: Keep the exterior of the valve clean. Avoid using harsh chemicals that could damage the valve material.
- Detekce úniku: Periodically check for leaks around the valve body and connections, especially after any system pressure changes.
- Provozní kontrola: Cycle the valve (open and close) periodically to ensure smooth operation and prevent seizing, particularly in systems where the valve remains in one position for extended periods.
6. Řešení problémů
This section addresses common issues that may arise with the service valve.
6.1 Běžné problémy a řešení
| Problém | Možná příčina | Řešení |
|---|---|---|
| Únik na spojích | Improper soldering; damaged pipe or valve connection | Depressurize system, repair or re-solder connection. Replace valve or pipe if damaged. |
| Valve difficult to turn | Internal corrosion or debris; lack of lubrication | Do not force. Depressurize system and inspect. If internal, valve replacement may be necessary. |
| No flow or restricted flow when open | Valve not fully open; internal obstruction | Ensure valve is fully open. Depressurize system and inspect for internal debris. |
V případě problémů, které zde nejsou uvedeny, nebo pokud řešení problém nevyřeší, obraťte se na kvalifikovaného servisního technika.
7. Specifikace
| Specifikace | Detail |
|---|---|
| Značka | ProTech |
| Číslo modelu | 61-104025-15 |
| Upper Connection Size | 3/4 palce |
| Upper Connection Type | Sweat ODF |
| Lower Connection Size | 3/4 palce |
| Lower Connection Type | Sweat ODF |
| Vnější povrch | Nerez |
| Počet portů | 2 |
| Specifikace splněna | ASME B16.34 |
| Hmotnost položky | 11.2 unce |
| Rozměry produktu (D x Š x V) | 3.8 x 3.2 x 4.3 palce |
| UPC | 662766520378 |
8. Informace o záruce
Unless otherwise noted, all Protech items carry a one-year limited warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
9. Podpora
For technical assistance, replacement parts, or further inquiries regarding the Protech 61-104025-15 Service Valve, please contact a qualified HVAC or plumbing professional. For general product information, you may visit the Obchod ProTech na Amazonu.
