Návod k použití popruhu na rameno s nastavitelnou délkou SafeWaze FS812

1. Úvod

This manual provides essential instructions for the proper use, installation, maintenance, and inspection of the SafeWaze FS812 Adjustable Length Cross Arm Strap. This device is designed to serve as a temporary anchorage connector for personal fall arrest systems. It is imperative that all users read and understand these instructions completely before using the product. Failure to follow these instructions can result in serious injury or death.

The SafeWaze FS812 is a critical component of a personal fall arrest system. It must be used in conjunction with other compatible fall protection equipment, including a full-body harness and a connecting device (e.g., lanyard, self-retracting lifeline).

2. Důležité bezpečnostní informace

WARNING: This product is part of a personal fall arrest system. Misuse or failure to follow instructions can result in serious injury or death.

• Only trained and competent persons should use this equipment.
• Inspect the strap before each use for damage, wear, or degradation. Do not use if any defects are found.
• Ensure the anchorage point can support a minimum of 5,000 lbs (22.2 kN) per worker attached, or meet OSHA 1926.502 and ANSI Z359.1 standards.
• Always calculate fall clearance to prevent striking a lower level or obstruction.
• Do not modify the equipment. Repairs must only be performed by the manufacturer or authorized personnel.
• Chránit webbing from sharp edges, abrasive surfaces, and high temperatures.
• Never connect multiple lanyards or devices to a single D-ring unless specifically designed for such use.
• In the event of a fall, immediately remove the strap from service and destroy it.

3. Součásti

The SafeWaze FS812 Adjustable Length Cross Arm Strap consists of the following primary components:

• Webbing: 1.75 inch (44.45 mm) wide polyester webbing, high-visibility lime green.
• D-kroužky: Two forged steel D-rings, one larger and one smaller, for connection and pass-through.
• Šití: High-strength polyester stitching securing all components.
• Adjuster: A buckle or similar mechanism for adjusting the strap's length.

Obrázek 1: The SafeWaze FS812 Adjustable Length Cross Arm Strap. This image displays the lime green polyester webbing with two forged steel D-rings at each end. One D-ring is larger, allowing the other D-ring to pass through it for secure anchorage. An adjustment buckle is visible on one side of the webbing.

4. Nastavení a instalace

The cross arm strap is designed to create a temporary anchorage point around a suitable structural member.

1. Select an Anchorage Point: Identify a structural member (e.g., beam, pipe) that is capable of supporting the required load (minimum 5,000 lbs or 22.2 kN per worker). The anchorage point must be free of sharp edges, burrs, or abrasive surfaces that could damage the webbing.
2. Zabalte popruh: Wrap the SafeWaze FS812 strap around the selected structural member.
3. Connect D-Rings: Pass the smaller D-ring through the larger D-ring.
4. Zabezpečte připojení: Pull the smaller D-ring tight against the structural member, ensuring the strap is snug and securely anchored. The larger D-ring should now be accessible for connection to your personal fall arrest system.
5. Adjust Length (if applicable): If the strap features an adjustment mechanism, ensure it is set to the appropriate length to minimize slack and maintain a secure fit around the anchorage.
6. Zkontrolujte konečné nastavení: Visually inspect the entire setup to confirm the strap is correctly installed, free from twists, and not compromised by any hazards.

Důležité: The anchorage point must be located above the user's head to minimize fall distance.

5. Návod k obsluze

Once the SafeWaze FS812 Cross Arm Strap is securely installed as an anchorage connector:

1. Connect Fall Arrest System: Attach your personal fall arrest system's connecting device (e.g., lanyard, self-retracting lifeline) to the larger D-ring of the cross arm strap.
2. Ověřit připojení: Ensure the connecting device is properly engaged and locked onto the D-ring.
3. Maintain Clearances: Always be aware of your surroundings and maintain adequate fall clearance below your work area.
4. Pravidelná kontrola: Periodically check the anchorage connection and the entire fall arrest system during use to ensure continued integrity.

6. Údržba a skladování

6.1 Kontrola

A thorough inspection of the SafeWaze FS812 strap must be performed by the user before each use and by a competent person at least annually.

• Webbing: Check for cuts, fraying, burns, chemical damage, discoloration, excessive wear, or broken stitches.
• D-kroužky: Inspect for deformation, cracks, corrosion, sharp edges, or any signs of damage. Ensure they pivot freely if designed to do so.
• Šití: Verify all stitching is intact and free from cuts, breaks, or loose threads.
• Štítky: Ensure all labels are present and legible.
• If any defects are found, immediately remove the strap from service.

6.2 Čištění

Clean the strap with a mild soap and water solution. Rinse thoroughly with clean water and allow to air dry completely in a shaded, well-ventilated area away from direct sunlight or heat. Do not use harsh chemicals, solvents, or abrasive cleaners.

6.3 Skladování

Store the strap in a cool, dry, clean environment, away from direct sunlight, extreme temperatures, corrosive chemicals, and sharp objects.

7. Řešení problémů

Most issues with fall protection equipment relate to improper inspection or installation.

• Řemínek se zdá být poškozený: Do not use. Remove from service immediately.
• D-rings are bent or corroded: Do not use. Remove from service immediately.
• Strap does not fit securely around anchorage: Re-evaluate the chosen anchorage point. Ensure the strap is wrapped and connected correctly, and adjust if possible. If a secure fit cannot be achieved, select a different anchorage point.
• Labels are missing or illegible: Do not use. Remove from service immediately.

If you encounter any issues not covered here, or if you are unsure about the safety or proper use of the product, contact SafeWaze customer support.

8. Specifikace

9. Záruka a podpora

For information regarding product warranty, please refer to the official SafeWaze warranty policy available on their webwebu nebo se přímo obraťte na jejich oddělení zákaznických služeb.

For technical support, questions about product use, or to report any issues, please contact SafeWaze customer support.

• Výrobce: SafeWaze
• Webmísto: www.safewaze.com (Napřampodkaz, skutečný odkaz se může lišit)
• Kontakt: Viz pokyny výrobce webstránky s aktuálními kontaktními informacemi.