Hager MUN110A Automatic Miniature Circuit Breaker User Manual

1. Úvod

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the Hager MUN110A Automatic Miniature Circuit Breaker.

The Hager MUN110A is a single-pole (1P) automatic miniature circuit breaker with a nominal current of 10A and a C curve, offering a breaking capacity of 6000A according to UNE EN 60898-1. It is AENOR certified.

Mezi klíčové vlastnosti patří:

• Number of poles: 1 P
• Rated nominal current: 10 A
• Jmenovitá frekvence: 50/60 Hz

2. Bezpečnostní informace

WARNING: Electrical shock hazard. Installation and maintenance must be performed by qualified personnel only.

• Always disconnect power at the main supply before installing, servicing, or removing the circuit breaker.
• Zajistěte dodržování všech místních a národních elektrických předpisů a předpisů.
• Pokud se zařízení zdá poškozené, nepoužívejte jej.
• V případě potřeby zajistěte řádné uzemnění.
• Verify correct wiring connections before restoring power.

3. Konec produktuview

Image showing the Hager MUN110A automatic miniature circuit breaker. It is a compact, single-module device, typically white or light grey, designed for DIN rail mounting. The front features the Hager logo, model number (MUN 110A), and curve type (C10). It has a toggle switch for ON/OFF operation and connection terminals at the top and bottom. The side of the breaker shows a barcode and text indicating 'MADE IN FRANCE' and the GTIN: 3250614316371.

The Hager MUN110A is designed for overcurrent protection in electrical circuits. Its main components include:

• Přepnout spínač: Používá se k ručnímu zapnutí nebo vypnutí jističe a indikuje vypnutý stav.
• Připojovací terminály: Screw terminals at the top and bottom for connecting incoming and outgoing conductors.
• Spona na DIN lištu: Located at the rear for easy mounting onto a standard DIN rail.

4. Nastavení (instalace)

1. Odpojení napájení: Před spuštěním se ujistěte, že je hlavní napájení elektrického panelu zcela odpojeno. Ověřte pomocí objemovéhotage tester.
2. Montáž: Attach the MUN110A circuit breaker onto a standard DIN rail within the electrical distribution board. Ensure it clicks securely into place.
3. Zapojení:
   • Connect the incoming phase conductor to the top terminal of the circuit breaker.
   • Connect the outgoing phase conductor (to the load) to the bottom terminal of the circuit breaker.
   • Ensure all connections are tight and secure. Recommended torque for terminal screws should be followed as per electrical standards.
4. Ověření: Před obnovením napájení dvakrát zkontrolujte správnost a bezpečnost veškerého zapojení.

5. Provoz

• Zapínání: To energize the circuit, push the toggle switch upwards to the 'ON' position.
• Vypínání: Chcete-li obvod odpojit od napájení, přepněte přepínač dolů do polohy „VYPNUTO“.
• Automatické vypnutí: In the event of an overload or short circuit, the circuit breaker will automatically trip to the middle or 'OFF' position, interrupting the power supply to protect the circuit.
• Resetting After Tripping:
  1. Identifikujte a odstraňte příčinu vypnutí (např. odstraňte přetížené spotřebiče, opravte zkraty).
  2. Move the toggle switch fully to the 'OFF' position.
  3. Then, push the toggle switch upwards to the 'ON' position to restore power.

6. Údržba

The Hager MUN110A circuit breaker is designed for long-term, maintenance-free operation under normal conditions. However, periodic visual inspections are recommended:

• Inspect for any visible damage, cracks, or discoloration on the casing.
• Ensure terminal connections remain tight. Loose connections can lead to overheating.
• Keep the area around the circuit breaker clean and free from dust or debris.

Note: There are no user-serviceable parts inside the circuit breaker. Do not attempt to open or repair the device.

7. Řešení problémů

• Problém: Jistič často vypíná.
  Řešení: This usually indicates an overload or a short circuit in the protected circuit. Disconnect all appliances from the circuit and reset the breaker. If it holds, reconnect appliances one by one to identify the faulty one. If it trips immediately without any load, there might be a short circuit in the wiring. Consult a qualified electrician.
• Problém: The circuit breaker does not reset.
  Řešení: Ensure the toggle switch is moved fully to the 'OFF' position before attempting to reset to 'ON'. If it still does not reset, the fault (overload or short circuit) might still be present, or the breaker itself may be faulty and require replacement. Do not force the switch.
• Problém: The circuit breaker feels hot.
  Řešení: This could indicate an overload, loose connections, or an internal fault. Immediately disconnect power and have the circuit and breaker inspected by a qualified electrician.

8. Specifikace

9. Záruka a podpora

For specific warranty information regarding your Hager MUN110A circuit breaker, please refer to the documentation provided at the time of purchase or contact your authorized Hager distributor or retailer.

For technical assistance, installation queries, or troubleshooting beyond the scope of this manual, it is recommended to contact a qualified electrician or Hager customer support directly.