WaterCop Wireless Flood Sensor (WCDFS1) Instruction Manual

1. Úvod

The WaterCop Wireless Flood Sensor (WCDFS1) is designed to detect the presence of water and transmit a wireless signal to a compatible WaterCop automatic water shut-off system. This system helps prevent water damage by automatically activating the shut-off valve when a leak is detected.

This sensor operates wirelessly, providing flexible placement options up to 200 feet from the main WaterCop system. It is powered by standard AA alkaline batteries.

2. Obsah balení

• WaterCop Wireless Flood Sensor (WCDFS1)
• Remote Probe with cable
• Montážní materiál (šrouby, kotvy)
• Tento návod k použití

3. Bezpečnostní informace

• Před instalací a provozem si přečtěte všechny pokyny.
• Do not expose the sensor to extreme temperatures or direct sunlight.
• Ujistěte se, že jsou baterie správně vloženy podle vyznačené polarity.
• Replace batteries annually or when indicated by the WaterCop system.
• Toto zařízení je určeno pouze pro vnitřní použití.

4. Nastavení a instalace

4.1 Instalace baterie

The WaterCop WCDFS1 sensor requires two (2) AA alkaline batteries (not included).

1. Opatrně otevřete senzor casing. Refer to the diagram for assistance.
2. Insert two AA alkaline batteries, observing the correct polarity (+/-) as marked inside the battery compartment.
3. Zavřete senzor casinbezpečně.

A pair of standard AA alkaline batteries should operate the sensor for approximately one year.

4.2 Umístění snímače

Place the sensor in areas prone to water leaks, such as near water heaters, washing machines, dishwashers, sinks, toilets, or in basements.

The sensor transmits a wireless signal up to 200 feet to the WaterCop control unit. Consider potential obstructions like thick walls or metal objects that may reduce signal range.

The remote probe should be positioned directly on the floor or surface where water accumulation is most likely to occur.

4.3 Pairing with WaterCop System

The WCDFS1 sensor is compatible with all WaterCop systems. Refer to your specific WaterCop control unit's manual for detailed instructions on how to pair new sensors. Generally, this involves placing the control unit into a "learn" mode and then activating the sensor.

4.4 Montáž

The sensor unit can be wall-mounted using the provided hardware. Ensure the remote probe cable reaches the desired detection area.

5. Provoz

Once installed and paired, the WaterCop Wireless Flood Sensor continuously monitors for the presence of water at its remote probe.

Upon detecting water, the sensor immediately transmits a wireless signal to the WaterCop control unit.

The WaterCop control unit, upon receiving this signal, will activate the automatic shut-off valve, thereby stopping the water supply to prevent further damage.

The sensor will continue to transmit the alarm signal until the water is no longer detected by the probe.

6. Údržba

6.1 Výměna baterie

Replace the AA alkaline batteries annually or when the WaterCop control unit indicates a low battery signal from the sensor.

1. Otevřete senzor casing.
2. Vyjměte staré baterie a zlikvidujte je zodpovědně.
3. Vložte dvě nové alkalické baterie typu AA a dbejte na správnou polaritu.
4. Zavřete senzor casinbezpečně.

6.2 Čištění

Periodically inspect the sensor and probe for dust or debris. Clean with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.

6.3 Testování

It is recommended to test the sensor's functionality periodically (e.g., every 3-6 months).

1. Place a small amount of water (e.g., a few drops) on the remote probe.
2. Observe if the WaterCop control unit receives the alarm signal and activates the shut-off valve.
3. Remove the water from the probe and verify that the WaterCop system resets or allows manual reset.
4. Refer to your WaterCop control unit's manual for specific testing procedures.

7. Řešení problémů

7.1 Sensor not detecting water:

• Ensure the remote probe is making good contact with the surface.
• Zkontrolujte stav baterie a v případě potřeby ji vyměňte.
• Verify the sensor is correctly paired with the WaterCop control unit.

7.2 WaterCop system not responding to sensor:

• Check the sensor's batteries.
• Ensure the sensor is within the 200 ft wireless range of the WaterCop control unit and there are no significant obstructions.
• Re-pair the sensor with the WaterCop control unit.
• Consult the WaterCop control unit's manual for troubleshooting its reception.

7.3 False alarms:

• Ensure the probe is not placed in an area where condensation or minor spills are common and not indicative of a leak.
• Check for any moisture on the probe that might be causing a false trigger.

8. Specifikace

9. Záruka a podpora

For warranty information and technical support, please refer to the official WaterCop webnebo se obraťte přímo na jejich zákaznický servis. Uschovejte si doklad o koupi pro případ reklamace.

Official WaterCop Webmísto: www.watercop.com

Contact Information: Refer to the webstránky s aktuálními kontaktními údaji.