Příručky+

Solight V15

Uživatelská příručka multimetru Solight V15 II CAT III

Model: V15 II | Brand: Solight

1. Úvod

Thank you for choosing the Solight V15 II CAT III Multimeter. This device is designed for safe and accurate measurement of DC/AC voltage, DC current, resistance, diode testing, and continuity. Please read this manual thoroughly before use to ensure proper operation and to prevent damage to the meter or injury to yourself.

Bezpečnost především: Always observe all safety precautions outlined in this manual. Electrical measurements can be dangerous if not performed correctly.

2. Konec produktuview

Solight V15 II CAT III Multimeter with red and black test leads

Obrázek 1: Solight V15 II Multimeter and Test Leads. The image displays the front of the Solight V15 II multimeter, which is dark gray with a large digital display at the top. Below the display is a central rotary switch for selecting measurement functions and ranges. To the left of the multimeter are two test leads: one red and one black, each with a pointed probe tip and a comfortable grip. The multimeter features input jacks at the bottom for connecting these leads.

2.1 Komponenty

3. Nastavení

3.1 Instalace baterie

  1. Ujistěte se, že je multimetr VYPNUTÝ.
  2. Vyhledejte kryt přihrádky na baterie na zadní straně jednotky.
  3. Odšroubujte upevňovací šroub(y) a sejměte kryt.
  4. Insert two (2) AAA (LR03) batteries, observing the correct polarity (+ and -) as indicated inside the compartment.
  5. Nasaďte kryt baterie a zajistěte jej šroubem (šrouby).
  6. If the low battery indicator appears on the display, replace the batteries promptly.

3.2 Připojení měřicích kabelů

4. Návod k obsluze

Before taking any measurement, ensure the test leads are correctly connected and the rotary switch is set to the appropriate function and range. Always start with a higher range if the expected value is unknown to prevent overloading the meter.

4.1 DC svtage Measurement (V--)

  1. Nastavte otočný přepínač na požadovanou hlasitost DCtage (V--) range (e.g., 500V, 200V, 20V, 2000mV, 200mV).
  2. Connect the black test lead to the "COM" jack and the red test lead to the "VΩmA" jack.
  3. Connect the test probes across the component or circuit to be measured, observing polarity.
  4. Přečtěte si svtage value on the digital display. If a negative sign appears, it indicates reversed polarity.

4.2 AC svtagMěření (V~)

  1. Nastavte otočný přepínač na požadovanou hlasitost střídavého proudutagrozsah e (V~) (např. 500 V, 200 V).
  2. Connect the black test lead to the "COM" jack and the red test lead to the "VΩmA" jack.
  3. Připojte měřicí sondy k vodiči AC volt.tage zdroj.
  4. Přečtěte si svtage hodnotu na digitálním displeji.

4.3 DC Current Measurement (A--)

  1. DŮLEŽITÉ: Current measurements require the meter to be connected in series with the circuit. Ensure the circuit is de-energized before connecting the meter.
  2. Set the rotary switch to the desired DC Current (A--) range (e.g., 10A, 200mA, 20mA, 2000µA, 200µA).
  3. For ranges up to 200mA, connect the red test lead to the "VΩmA" jack. For the 10A range, connect the red test lead to the "10A" jack. The black lead always connects to "COM".
  4. Open the circuit where current is to be measured and insert the meter in series.
  5. Zapněte obvod a odečtěte hodnotu proudu na displeji.
  6. After measurement, disconnect power, remove the meter, and restore the circuit.

4.4 Měření odporu (Ω)

  1. VAROVÁNÍ: Ensure the circuit or component under test is completely de-energized before measuring resistance.
  2. Set the rotary switch to the desired Resistance (Ω) range (e.g., 20000kΩ, 2000kΩ, 200kΩ, 20kΩ, 2000Ω, 200Ω).
  3. Connect the black test lead to "COM" and the red test lead to "VΩmA".
  4. Připojte měřicí sondy napříč součástkou.
  5. Odečtěte hodnotu odporu na displeji.

4.5 Test diod (→|→)

  1. Set the rotary switch to the Diode Test position.
  2. Connect the black test lead to "COM" and the red test lead to "VΩmA".
  3. Připojte červenou sondu k anodě a černou sondu ke katodě diody. Displej by měl ukazovat směr proudu.tagpokles napětí (obvykle 0.5 V až 0.8 V u křemíkových diod).
  4. Reverse the probes. The display should show "OL" (Overload) for a good diode. If it shows a reading in both directions or "OL" in both directions, the diode is likely faulty.

4.6 Zkouška kontinuity (•))))

  1. Set the rotary switch to the Continuity Test position.
  2. Connect the black test lead to "COM" and the red test lead to "VΩmA".
  3. Připojte měřicí sondy k obvodu nebo součástce.
  4. If the resistance is below approximately 50Ω (this value can vary), the buzzer will sound, indicating continuity. The display will also show the resistance value.

5. Specifikace

Funkce měřeníRozsahPřesnost
DC svtage (V--)200 mV, 2000 20 mV, 200 V, 500 V, XNUMX V±1.0 % čtení + 2 číslic
AC svtage (V~)200V, 500V±1.2 % čtení + 10 číslic
DC Current (A--)200µA, 2000µA, 20mA, 200mA, 10A±1.5 % čtení + 2 číslic
Odpor (Ω)200Ω, 2000Ω, 20kΩ, 200kΩ, 2000kΩ, 20000kΩ±1.0 % čtení + 2 číslic
Test diodAnoVpřed svtagdisplej s e-drop
Test kontinuityAno (s bzučákem)Buzzer sounds below approx. 50Ω

Obecné specifikace

6. Údržba

6.1 Čištění

Otřete měřič casing s reklamouamp hadříkem a jemným čisticím prostředkem. Nepoužívejte abrazivní prostředky ani rozpouštědla. Před použitím se ujistěte, že je měřič zcela suchý.

6.2 Výměna baterie

When the low battery indicator appears on the display, replace the two AAA batteries as described in Section 3.1. Remove batteries if the meter is not used for an extended period to prevent leakage.

6.3 Výměna pojistky

If the current measurement function stops working, the fuse may be blown. Fuses are located inside the meter. Fuse specifications are 500mA/500V for the VΩmA input and 10A/500V for the 10A input. Fuse replacement should only be performed by qualified personnel. Always replace with fuses of the exact same type and rating.

7. Řešení problémů

8. Bezpečnostní informace

This multimeter is designed to meet safety standards for electrical measuring instruments. However, improper use can result in electric shock or damage to the meter. Always follow these safety guidelines:

9. Záruka a podpora

This Solight V15 II Multimeter is designed for reliability. For any warranty claims or technical support, please contact your retailer or the Solight customer service department. Please retain your proof of purchase for warranty purposes.