Konec produktuview
This manual provides essential information for the safe and effective installation, operation, and maintenance of the OEM ICP Heil Tempstar Emerson Blower Motor, model HQ1013341EM / 1013341 (K55HXJEW-9056). This motor is a critical component for various HVAC systems, designed for reliable performance.
Mezi klíčové vlastnosti patří:
- 1/2 Horsepower (HP)
- 115 Volts (V) operating voltage
- 1050 otáček za minutu (RPM)
- Thermally Protected design for enhanced safety
- Compatible with a 7.5 MFD, 370 VAC capacitor
- Frame 48Y, 5 5/8" diameter
Always refer to the specific wiring diagrams and safety instructions provided with your HVAC unit and this motor.
Bezpečnostní informace
VAROVÁNÍ: To reduce the potential for electrical shock, always disconnect power before servicing the motor or any associated equipment. Failure to do so can result in serious injury or death. Follow all national and local codes for grounding and ensure unused lead wires are insulated individually.
- Ensure proper grounding according to all applicable electrical codes.
- Instalaci a údržbu by měl provádět pouze kvalifikovaný personál.
- Verify that the power supply matches the motor's voltage požadavky (115V).
- Do not operate the motor if it appears damaged.
- Keep hands and tools clear of moving parts during operation.
Nastavení a instalace
Proper installation is crucial for the longevity and safe operation of the blower motor. Refer to your HVAC system's specific service manual for detailed instructions on removing the old motor and installing the new one.
- Odpojení napájení: Before beginning any work, ensure the main power supply to the HVAC unit is completely disconnected and locked out to prevent accidental energization.
- Přístup: Open the access panels of your HVAC unit to reach the blower motor assembly.
- Odpojení kabeláže: Carefully disconnect the existing wiring from the old motor. Note the position and color of each wire for correct re-connection. This motor is a 4-speed motor.
- kondenzátor: This motor requires a 7.5 MFD, 370 VAC capacitor. Ensure the correct capacitor is installed and properly wired.
- Demontáž motoru: Unmount the old motor from its housing or cradle. The shaft extends 4 inches out of the motor.
- Instalace nového motoru: Mount the new Genteq blower motor (model K55HXJEW-9056 / HQ1013341EM) securely in place. Ensure it is properly aligned with the blower wheel.
- Připojení kabeláže: Connect the new motor's wires according to the wiring diagram below and your HVAC unit's specifications. Insulate any unused lead wires individually.
Obraz: OEM ICP Heil Tempstar Emerson Blower Motor (Model K55HXJEW-9056 / HQ1013341EM). This image displays the motor with its various colored wires and a label detailing its specifications and a wiring diagram. The motor is dark gray with a silver top grille, and the shaft extends vertically from the center. The wiring harness includes brown, white, black, orange, blue, and red wires, each with a spade connector. The label clearly shows the model number, electrical ratings, and a schematic for connecting the motor to a capacitor and line voltage.
Odkaz na schéma zapojení
The motor features a clear wiring diagram on its label. Ensure connections are made precisely as indicated:
| Barva drátu | Funkce |
|---|---|
| Hnědý | Capacitor Connection |
| bílá (COM) | Common Line Connection |
| Black (HI) | High Speed Connection |
| Orange (MED-HI) | Medium-High Speed Connection |
| Blue (MED-LOW) | Medium-Low Speed Connection |
| Red (LOW) | Low Speed Connection |
The green wire with a ring terminal is for grounding the motor to the system chassis.
Návod k obsluze
Once installed and wired correctly, the blower motor operates in conjunction with your HVAC system's control board. The motor is designed for continuous air over operation, meaning it relies on airflow for cooling.
- The motor will activate when the HVAC system calls for heating or cooling, or for continuous fan operation.
- Speed selection (High, Medium-High, Medium-Low, Low) is determined by the HVAC system's control board based on the connected wiring.
- Ensure that the blower wheel is clean and free of obstructions to allow for proper airflow and efficient motor operation.
Údržba
Pravidelná údržba pomáhá zajistit dlouhou životnost a účinnost motoru ventilátoru. Před prováděním jakékoli údržby vždy odpojte napájení.
- Čištění: Periodically inspect the motor and blower wheel for dust and debris accumulation. Clean with a soft brush or vacuum cleaner. Do not use liquids directly on the motor.
- Inspekce: Check wiring connections for tightness and signs of wear or damage. Inspect the motor for any unusual noises or vibrations during operation.
- Ložiska: This motor typically features sealed bearings that do not require lubrication. Refer to the manufacturer's specifications if unsure.
- Kontrola kondenzátoru: If the motor is not starting or running correctly, the capacitor may need to be tested or replaced by a qualified technician.
Odstraňování problémů
This section provides guidance for common issues. For complex problems, consult a qualified HVAC technician.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Motor se nespustí | No power, faulty capacitor, wiring error, motor overload/thermal trip. | Check power supply and circuit breaker. Inspect capacitor for bulging or leaks; test with a multimeter. Verify all wiring connections. Allow motor to cool if thermally tripped. |
| Motor běží, ale neproudí proudění vzduchu | Blower wheel detached or obstructed. | Inspect blower wheel for secure attachment to the motor shaft. Clear any obstructions from the blower housing. |
| Motor vydává neobvyklý zvuk | Worn bearings, foreign object in blower, unbalanced blower wheel. | Inspect for foreign objects. Check blower wheel for balance and damage. If bearings are worn, motor replacement may be necessary. |
| Motor se přehřívá a vypíná | Restricted airflow, incorrect voltage. přetížení motoru. | Ensure air filters are clean and ducts are unobstructed. Verify correct voltage supply. Check for excessive load on the motor. |
Specifikace
| Atribut | Hodnota |
|---|---|
| Číslo modelu | HQ1013341EM / 1013341 (K55HXJEW-9056) |
| Výrobce | ICP / Heil / Tempstar (Emerson/Genteq) |
| koňská síla (HP) | 1/2 koní (0.5 koní) |
| svtage | 115 voltů |
| Ampvymazat (AMP) | 8.0 A |
| Otáčky za minutu (RPM) | 1050 ot./min (4stupňová) |
| Frekvence (HZ) | 60 Hz |
| Phase (PH) | 1 fáze |
| Velikost rámu | 48Y (5 5/8" diameter) |
| Prodloužení hřídele | 4 palců |
| Capacitor Requirement | 7.5 MFD, 370 VAC |
| Tepelná ochrana | Thermally Protected (PROT.CODE 7A010) |
| Insulation Class (INS CL) | B |
| Ambient Temperature (AIR OVER CONT) | 40 °C |
| UPC | 751109532007 |
Informace o záruce
This product is manufactured by ICP / Heil / Tempstar, with the motor component often supplied by Emerson/Genteq. For specific warranty terms and conditions, please refer to the documentation provided with your original HVAC unit or contact the manufacturer directly. Extended protection plans may be available from your retailer at the time of purchase.
Podpora a kontakt
For technical assistance, parts inquiries, or further information regarding your blower motor, please contact the manufacturer or a certified HVAC technician.
- Výrobce Webmísto: www.usmotors.com (NIDEC Motor Corporation)
- For ICP/Heil/Tempstar specific support, refer to their official websites or customer service channels.
